1、AEROSPACE STANDARDINSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, FLUOROELASTOMER, FLEXIBLEAS23053/13Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical,
2、photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2016-10THIRD ANGLE PROJECT
3、IONCUSTODIAN: AE-8/AE-8DFEDERAL SUPPLY CLASS5970AS23053/13SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS23053SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportis entirely voluntary, and its applicabili
4、ty and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your written comments and suggesti
5、ons.SAE values your input. To provide feedback on thisTechnical Report, please visit http:/standards.sae.org/AS23053/13RATIONALETHIS IS A CONVERSION OF AMS-DTL-23053/13 INTO AN AEROSPACE STANDARD WHICH INCLUDESQUALIFICATION AND REQUIREMENTS FOR A QUALIFIED PRODUCTS LIST.NOTICETHE COMPLETE REQUIREMEN
6、TS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LASTEST ISSUE OF AS23053.REQUIREMENTS1. DIMENSIONS AND PROPERTIES IN INCH/POUND UNITS AND THE FAHRENHEIT TEMPERATURES AREPRIMARY; DIMENSIONS AND PROPERTIES IN SI UNITS AND THE CELSIUS TEMPERATURES ARE SHOWN AS THE A
7、PPROXIMATE EQUIVALENTS OF THE PRIMARY UNITS AND ARE PRESENTED ONLY FOR INFORMATION.2. POLYMER TYPE: THE BASE ELASTOMER USED IN FORMULATING THIS SLEEVING SHALL BE FLUOROELASTOMER.3. CONTINUOUS OPERATING TEMPERATURE RANGE: -40 TO +392 F (-40 TO +200 C).4. COLOR: THE HEAT SHRINKABLE SLEEVING SHALL BE F
8、URNISHED IN THE COLOR SPECIFIED BY THE ACQUISITION ACTIVITY (SEE 7.3); HOWEVER, BLACK SHALL BE CONSIDERED STANDARD. COLORS SHALLCONFORM TO THE REQUIREMENTS OF CLASS II OF MIL-STD-104. (SEE 1.3 AND 3.3.3)5. LONGITUDINAL CHANGE: 20%.6. PART NUMBER: THE PART NUMBER SHALL BE AS LISTED BELOW:M23053/13 -
9、X XX - XEXAMPLE: BLACK, 0.500 INCH (12.7 MM) AS SUPPLIED ID SLEEVING SHALL BE IDENTIFIED AS M23053/13-004-0.7. DIMENSIONAL LIFE: THE DIMENSIONAL LIFE OF A PRODUCT APPLIES TO THE EXPANDED I.D., RECOVERED I.D., AND WALL THICKNESS DIMENSIONS OF THE PRODUCT AS SOLD BY THE MANUFACTURER, DISTRIBUTORS, AND
10、 REBRAND DISTRIBUTORS. AS23053/13 PRODUCTS CAN BE EXPECTED TO HAVE A MINIMUM DIMENSIONAL LIFE OF 2 YEARS WHEN STORED BETWEEN 32 TO 95 F (0 TO 35 C). PRODUCTSSTORED ABOVE THESE CONDITIONS MAY NOT MEET THE MINIMUM EXPANDED I.D. REQUIREMENTS OF THE DETAIL SPECIFICATION. A PRODUCT MAY BE USED BY THE FIN
11、AL PURCHASER BEYOND THE EXPECTEDMINIMUM DIMENSIONAL LIFE, AS LONG AS THE EXPANDED I.D., RECOVERED I.D., AND WALL THICKNESS OF THE PRODUCT MEET THE REQUIREMENTS OF THIS SPECIFICATION AT THE TIME OF USE.8. UNRESTRICTED SHRINKAGE: TEST METHOD 5.5; 392 F 9 F (200 C 5 C) FOR 10 MINUTES MAXIMUM.COLOR CODE
12、 DESIGNATOR (SEE 1.3)SIZE IDENTIFIER (SEE TABLE 1)CLASS (WHERE NO CLASSES ARE SPECIFIED IN THE SPECIFICATION SHEET, THE NUMERIC “0” IS USED)SPECIFICATION SHEETAEROSPACE STANDARD AS23053/13SHEET 2 OF 3INSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, FLUOROELASTOMER, FLEXIBLETABLE 1 - CONSTRUCTION DET
13、AILS, INCHES (MM) 1/PART NUMBER 3/AS SUPPLIEDID MINIMUMAFTER UNRESTRICTED SHRINKAGEID MAXIMUM WALL THICKNESS 2/M23053/13-001-* .187 (4.7) .094 (2.4) .035 .007 (0.9 0.2)M23053/13-002-* .250 (6.4) .125 (3.2) .035 .007 (0.9 0.2)M23053/13-003-* .375 (9.5) .187 (4.7) .035 .007 (0.9 0.2)M23053/13-004-* .5
14、00 (12.7) .250 (6.4) .035 .007 (0.9 0.2)M23053/13-005-* .625 (15.9) .312 (7.9) .042 .008 (1.1 0.2)M23053/13-006-* .750 (19.1) .375 (9.5) .042 .008 (1.1 0.2)M23053/13-007-* .875 (22.2) .437 (11.1) .049 .011 (1.2 0.3)M23053/13-008-* 1.000 (25.4) .500 (12.7) .049 .011 (1.2 0.3)M23053/13-009-* 1.250 (31
15、8) .625 (15.9) .055 .015 (1.4 0.4)M23053/13-010-* 1.500 (38.1) .750 (19.1) .055 .015 (1.4 0.4)M23053/13-011-* 2.000 (50.8) 1.000 (25.4) .065 .017 (1.7 0.4)M23053/13-012-* .125 (3.2) .063 (1.6) .030 .007 (0.8 0.2)1/ DIAMETER LIMITS FOR OBJECT TO BE ENCLOSED SHALL BE AS SPECIFIED INTECHNICAL DATA.2/
16、WALL THICKNESS VALUES ARE LESS WHEN SHRINKAGE IS RESTRICTED.3/ THE ASTERISK IN THE PART NUMBER SHALL BE REPLACED BY COLOR CODE DESIGNATIONS (SEE 1.3). BLACK IS THE STANDARD COLOR.TABLE 2 - PHYSICAL PROPERTIESCHARACTERISTIC REQUIREMENTTEST PROCEDURE AND CONDITION(SEE AS23053)AS SUPPLIED:ID, MINIMUM T
17、ABLE 1 5.3.1COLD IMPACT NO CRACKING 5.7.2; -40 F 1 F (-40 C 2 C)HEAT SHOCK NO CRACKS, FLOWING, OR DRIPPING 5.8; 572 F 9 F (300 C 5 C)RESTRICTED SHRINKAGE NO CRACKS 5.6; 392 F 4 F (200 C 2 C)VOLTAGE WITHSTAND PASS 5.6.2.CAFTER UNRESTRICTED SHRINKAGE:ID, MAXIMUM TABLE 1 5.3.2WALL THICKNESS TABLE 1 5.3
18、3TENSILE STRENGTH, PSI (MPa), MINIMUM1200 (8.2) 5.13; ASTM D412, 20 INCHES/MINUTEULTIMATE ELONGATION, PERCENT250 5.13; ASTM D412, 20 INCHES/MINUTETENSILE STRESS AT 200 PERCENT ELONGATION, PSI (MPa), MAXIMUM2000 (13.8) 5.12.2; ASTM D412DIELECTRIC STRENGTH, VOLTS/MIL, (KV/MM), MINIMUM200 (7.9) 5.2; A
19、STM D2671VOLUME RESISTIVITY, OHM-CM, MINIMUM1 X 109 5.2; ASTM D876AEROSPACE STANDARD AS23053/13SHEET 3 OF 3INSULATION SLEEVING, ELECTRICAL, HEATSHRINKABLE, FLUOROELASTOMER, FLEXIBLETABLE 2 - PHYSICAL PROPERTIES (CONTINUED)CHARACTERISTIC REQUIREMENTTEST PROCEDURE AND CONDITION(SEE AS23053)CORROSION N
20、O CORROSION OR PITTING 5.10.1 AND 5.10.2347 F 4 F (175 C 2 C) FOR 16 HOURS.HEAT RESISTANCE,PROPERTIES AFTER:5.9; 482 F 5.4 F (250 C 3 C) FOR 168 HOURSTENSILE STRENGTH, PSI (MPa), MINIMUM1200 (8.2)ULTIMATE ELONGATION, PERCENT, MINIMUM200WATER ABSORPTION,PERCENT, MAXIMUM0.5 5.2; ASTM D570, 24 HOURSAT
21、73 F (23 C)FLUID RESISTANCE,PROPERTIES AFTER:5.11TENSILE STRENGTH, PSI (MPa), MINIMUM1200 (8.2)ULTIMATE ELONGATION, PERCENT, MINIMUM250FLAMMABILITY SELF-EXTINGUISHING WITHIN 15 SECONDS5.14; PROCEDURE AASTM D2671FUNGUS RESISTANCEPROPERTIES AFTER:TENSILE STRENGTH, PSI (MPa), MINIMUMULTIMATE ELONGATION
22、PERCENT, MINIMUMDIELECTRIC STRENGTH,VOLTS/MIL (KV/MM), MINIMUMNO GROWTHOR1200 (8.2)250200 (7.9)5.17; ASTM G215.17; ISO 8465.2; ASTM D2671APPLICATION NOTES1. INTENDED USE: HEAT SHRINKABLE, FLEXIBLE, FLUOROELASTOMER SLEEVING IS USED IN HIGH TEMPERATURE APPLICATIONS OR WHERE EXPOSURE TO HIGH TEMPERATU
23、RE SOLVENTS IS EXPECTED.SPECIFICATION NOTES1. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
