1、AEROSPACE STANDARD PIN, EXPANSION - CRES, 416 OR 416SE, SHORT, UNS S41600/UNS S41623 AS3128Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyi
2、ng, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1981-02REAFFIRMED 2006-05 REVISE
3、D 2014-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5315 AS3128SHEET 1 OF 2REV. BPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entir
4、ely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites
5、 yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3128BRATIONALE THIS IS A LIMITED SCOPE REVISION. REVISED CLEANING REQUIREMENTS (NOTE 3) FOR CONFORMANCE TO AMS2700 OR ASTM A967/A967M. FIGURE
6、1 TABLE 1 - PART NUMBERS AND DIMENSIONS AEROSPACE STANDARD PART NUMBER /8/MANUFACTURERSPART NUMBER /8/ANOM B NOM C MAXD NOM ENOM F NOM APPROX MASSLB/100 AS3128-01 PLGA0934020A .062 .069 .020 .0417 30 .056 .006 AS3128-02 PLGA1254020 A .086 .095 .020 .0417 10 .087 .015 AS3128-03 PLGA1564020 A .078 .11
7、6 .032 .0417 13 .106 .020 AS3128-04 PLGA1874020 A .114 .154 .040 .0417 10 .139 .054 AS3128-05 PLGA2184020 A .145 .179 .040 .0417 (a) (a) .094 AS3128-06 PLGA2504020 A .160 .212 .040 .0417 10 .196 .146 AS3128-07 PLGA2814020 A .193 .245 .040 .0313 10 .233 .241 AS3128-08 PLGA3434020 A .216 .305 .060 .01
8、56 10 .289 .415 AS3128-09 PLGA4064020 A .255 .363 .060 .0208 10 .350 .699 AS3128-10 PLGA4684020 A .285 .436 .060 .0208 10 .420 1.141 AS3128-11 PLGA5314020 A .375 .494 .060 .0156 10 .479 1.937AS3128-12 PLGA6564020 A .390 .598 .060 .0182 10 .581 2.967 (a) AS3128-05 HAS A .01-.02 RADIUS INSTEAD OF A CH
9、AMFER. AEROSPACE STANDARD AS3128SHEET 2 OF 2REV. BPIN, EXPANSION - CRES, 416 OR 416SE, SHORT, UNS S41600/UNS S41623 NOTES: 1. MATERIAL: AMS5610 (416 OR 416SE CRES BAR), UNS S41600 OR UNS S41623. 2. HEAT TREAT: ROCKWE,LL 20-34 HRC PER ASTM E140. 3. CLEANING: FINISHED PARTS SHALL BE DEGREASED AND PASS
10、IVATED PER ASTM A967/A967M OR AMS2700. A SOLUTION CONTAINING SODIUM DICHROMATE AND NOT LESS THAN 20% BY VOLUME OF NITRIC ACID MUST BE USED. A CITRIC ACID METHOD MAY BE USED AS AN ALTERNATIVE IF REQUESTED BY THE PROCURING ACTIVITY AND THE SUPPLIER AGREES. 4. PINS ARE PREWAXED TO AID DRIVING. 5. SURFA
11、CE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 250 MICROINCHES Ra. 6. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCE: ANGULAR DIMENSIONS 2 DEGREES. DIMENSIONS APPLY AFT
12、ER FINISH. /8/ MARK AS3128-( ) PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE IN ACCORDANCE WITH AS478, METHOD 37. 9. USE WITH AS3127 PLUGS. SEE AIR3277 INSTALLATION PROCEDURES. 10. DIMENSIONING AND TOLERANCING: PER ASME Y14.5M-1994. 11. DO NOT USE UNASSIGNED PART NUMBERS. 12. SEE AS3585 FOR P
13、LUG AND PIN SET OF PARTS. 13. AS, AIR, AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION. 14. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TE
14、CHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS T
15、HAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDENT
16、IFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING.
