1、AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, AMS4967 (UNS R56400), 160 KSI, .5000-20 UNJF-3AAS3152Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any
2、 form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS:
3、http:/www.sae.org ISSUED 1976-11REAFFIRMED 2004-07 REVISED 2013-06THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5306 AS3152SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: AS7461 /8/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of
4、technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time it
5、may berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3152ARATIONALE REVISE THREAD SPECIFICATION TO AS8879. REVISE LIGHTENING HOLE CO
6、NFIGURATION (ADD SECTION VIEW) TO ALLOW OPTIONAL SHAPE AT BOTTOM OF HOLE, DELETE .015 MAX RADIUS AT BASE OF WRENCH PAD, UPDATE FPI REQUIREMENTS, ADD SURFACE FINISH REQUIREMENTS TO BOLT HEAD, ADD AS3062 FOR THREAD RUNOUT, UPDATE TO ANSI Y14.5M-1982, DELETE METRIC DIMENSIONS, UPDATE ANSI Y14.5-1973 TO
7、 ANSI Y14.5M- 1982, GENERAL EDITORIAL UPDATE, REFERENCES UDATED AND FIGURE 1 REDRAWN. FIGURE 1 - BOLT AEROSPACE STANDARD AS3152SHEET 2 OF 3REV. ABOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, AMS4967 (UNS R56400), 160 KSI, .5000-20 UNJF-3A TABLE 1 - PART NUMBERS AND DIME
8、NSIONS PART NO. L GMINKMAXAPPROX. MASSLB/100 PART NO. L GMINKMAXAPPROX. MASSLB/100 AS3152-03 .974- .994 .088 .198 4.88 AS3152-45 3.598-3.618 2.712 2.822 13.25 AS3152-04 1.036-1.056 .150 .260 5.09 AS3152-46 3.661-3.681 2.775 2.885 13.46 AS3152-05 1.098-1.118 .212 .322 5.27 AS3152-47 3.724-3.744 2.838
9、 2.948 13.65 AS3152-06 1.161-1.181 .275 .385 5.48 AS3152-48 3.786-3.806 2.900 3.010 13.86 AS3152-07 1.224-1.244 .338 .448 5.68 AS3152-49 3.848-3.868 2.962 3.072 14.06 AS3152-08 1.286-1.306 .400 .510 5.88 AS3152-50 3.911-3.931 3.025 3.135 14.25 AS3152-09 1.348-1.368 .462 .572 6.07 AS3152-51 3.974-3.9
10、94 3.088 3.198 14.46 AS3152-10 1.411-1.431 .525 .635 6.28 AS3152-52 4.036-4.056 3.150 3.260 14.65 AS3152-11 1.474-1.494 .588 .698 6.48 AS3152-53 4.098-4.118 3.212 3.322 14.84 AS3152-12 1.534-1.554 .650 .760 6.68 AS3152-54 4.161-4.181 3.275 3.385 15.05 AS3152-13 1.598-1.618 .712 .822 6.88 AS3152-55 4
11、.224-4.244 3.338 3.448 15.26 AS3152-14 1.661-1.681 .775 .885 7.08 AS3152-56 4.286-4.306 3.400 3.510 15.45 AS3152-15 1.724-1.744 .838 .948 7.28 AS3152-57 4.348-4.368 3.462 3.572 15.65 AS3152-16 1.786-1.806 .900 1.010 7.48 AS3152-58 4.411-4.431 3.525 3.635 15.85 AS3152-17 1.848-1.868 .962 1.072 7.68 A
12、S3152-59 4.474-4.494 3.588 3.698 16.05 AS3152-18 1.911-1.931 1.025 1.135 7.87 AS3152-60 4.536-4.556 3.650 3.760 16.25 AS3152-19 1.974-1.994 1.088 1.198 8.08 AS3152-61 4.598-4.618 3.712 3.822 16.45 AS3152-20 2.036-2.056 1.150 1.260 8.27 AS3152-62 4.661-4.681 3.775 3.885 16.65 AS3152-21 2.098-2.118 1.
13、212 1.322 8.47 AS3152-63 4.724-4.744 3.838 3.948 16.85 AS3152-22 2.161-2.181 1.275 1.385 8.67 AS3152-64 4.786-4.806 3.900 4.010 17.04 AS3152-23 2.224-2.244 1.338 1.448 8.87 AS3152-65 4.848-4.868 3.962 4.072 17.25 AS3152-24 2.286-2.306 1.400 1.510 9.07 AS3152-66 4.911-4.931 4.025 4.135 17.44 AS3152-2
14、5 2.348-2.368 1.462 1.572 9.27 AS3152-67 4.974-4.994 4.088 4.198 17.65 AS3152-26 2.411-2.431 1.525 1.635 9.48 AS3152-68 5.036-5.056 4.150 4.260 17.85 AS3152-27 2.474-2.494 1.588 1.698 9.67 AS3152-69 5.098-5.118 4.212 4.322 18.04 AS3152-28 2.534-2.554 1.650 1.760 9.86 AS3152-70 5.161-5.181 4.275 4.38
15、5 18.25 AS3152-29 2.598-2.618 1.712 1.822 10.07 AS3152-71 5.224-5.244 4.338 4.448 18.44 AS3152-30 2.661-2.681 1.775 1.885 10.27 AS3152-72 5.286-5.306 4.400 4.510 18.63 AS3152-31 2.724-2.744 1.838 1.948 10.47 AS3152-73 5.348-5.368 4.462 4.572 18.84 AS3152-32 2.786-2.806 1.900 2.010 10.67 AS3152-74 5.
16、411-5.431 4.525 4.635 19.05 AS3152-33 2.848-2.868 1.962 2.072 10.86 AS3152-75 5.474-5.494 4.588 4.698 19.24 AS3152-34 2.911-2.931 2.025 2.135 11.07 AS3152-76 5.536-5.556 4.650 4.760 19.44 AS3152-35 2.974-2.994 2.088 2.198 11.27 AS3152-36 3.034-3.054 2.150 2.260 11.46 AS3152-37 3.098-3.118 2.212 2.32
17、2 11.66 AS3152-38 3.161-3.181 2.275 2.385 11.86 AS3152-39 3.224-3.244 2.338 2.448 12.06 AS3152-40 3.286-3.306 2.400 2.510 12.26 AS3152-41 3.348-3.368 2.462 2.572 12.46 AS3152-42 3.411-3.431 2.525 2.635 12.66 AS3152-43 3.474-3.494 2.588 2.698 12.86 AS3152-44 3.534-3.554 2.650 2.760 13.06 AEROSPACE ST
18、ANDARD AS3152SHEET 3 OF 3REV. ABOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, AMS4967 (UNS R56400), 160 KSI, .5000-20 UNJF-3A NOTES: /1/ FOR PART NUMBERS AS3152-03 THRU AS3152-13 THE THREAD PD SHALL REPLACE DATUM B. 2. MATERIAL: TITANIUM ALLOY AMS4967 (SIMILAR TO UNS R56
19、400) 3. PROCUREMENT SPECIFICATION: AS7461. 4. FLUORESCENT PENETRANT INSPECTION PER E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .01
20、5 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. /8/ HEAD TO SHANK FILLET SHALL BE COLD ROLLED PER AS7461 AFTER HEAT TREATMENT. THE COLD ROLLING SHALL BE SUFFICIENT TO REMOVE ALL VISUAL EVIDENCE OF GRINDING OR TOOL MARKS EXCEPT THAT DISTORTIONS AT “A” IN FIGURE 2 OF THE SPECIFICATION SHALL NOT
21、 BE PERMITTED ON THE HEAD BEARING AREA AND SHALL BE PERMITTED ON THE SHANK DIAMETER ONLY IF THE DISTORTION DOES NOT CAUSE THE SHANK DIAMETER TO EXCEED .5000 DIAMETER. 9. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982 (ASME PUBLICATION). 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. A CHANGE BAR (l) LO
22、CATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION
