1、AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, AMS4967 (UNS R56400), 160 KSI, .5625-18, UNJF-3AAS3153Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in an
2、y form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS:
3、 http:/www.sae.org ISSUED 1976-11REAFFIRMED 2006-10 REVISED 2013-06THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5306 AS3153SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: AS7461 /8/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of
4、 technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time i
5、tmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3153ARATIONALE REVISE THREAD SPECIFICATION TO AS8879. REVISE LIGHTENING HOLE C
6、ONFIGURATION (ADD SECTION VIEW) TO ALLOW OPTIONAL SHAPE AT BOTTOM OF HOLE, DELETE .015 MAX RADIUS AT BASE OF WRENCH PAD, UPDATE FPI REQUIREMENTS, ADD SURFACE FINISH REQUIREMENTS TO BOLT HEAD, ADD AS3062 FOR THREAD RUNOUT, UPDATE TO ANSI Y14.5M-1982, DELETE METRIC DIMENSIONS, UPDATE ANSI Y14.5-1973 T
7、O ANSI Y14.5M-1982, GENERAL EDITORIAL UPDATE, REFERENCES UDATED AND FIGURE 1 REDRAWN. FIGURE 1 - BOLT AEROSPACE STANDARD AS3153SHEET 2 OF 3REV. ABOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, AMS4967 (UNS R56400), 160 KSI, .5625-18, UNJF-3A TABLE 1 - PART NUMBERS AND DIM
8、ENSIONS PART NO. L GMINKMAXAPPROX. MASSLB/100 PART NO. L GMINKMAXAPPROX. MASSLB/100 AS3153-03 1.056-1.076 .077 .198 7.05 AS3153-45 3.680-3.700 2.701 2.822 17.64 AS3153-04 1.118-1.138 .139 .260 7.30 AS3153-46 3.743-3.763 2.764 2.885 17.89 AS3153-05 1.180-1.200 .201 .322 7.54 AS3153-47 3.806-3.826 2.8
9、27 2.948 18.15 AS3153-06 1.243-1.263 .264 .385 7.80 AS3153-48 3.868-3.888 2.889 3.010 18.40 AS3153-07 1.306-1.326 .327 .448 8.05 AS3153-49 3.930-3.950 2.951 3.072 18.65 AS3153-08 1.368-1.388 .389 .510 8.31 AS3153-50 3.993-4.013 3.014 3.135 18.91 AS3153-09 1.430-1.450 .451 .572 8.55 AS3153-51 4.056-4
10、076 3.077 3.198 19.17 AS3153-10 1.493-1.513 .514 .635 8.81 AS3153-52 4.118-4.138 3.139 3.260 19.41 AS3153-11 1.556-1.576 .577 .698 9.06 AS3153-53 4.180-4.200 3.201 3.322 19.65 AS3153-12 1.618-1.638 .639 .760 9.32 AS3153-54 4.243-4.263 3.264 3.385 19.92 AS3153-13 1.680-1.700 .701 .822 9.56 AS3153-55
11、 4.306-4.326 3.327 3.448 20.17 AS3153-14 1.743-1.763 .764 .885 9.82 AS3153-56 4.368-4.388 3.389 3.510 20.42 AS3153-15 1.806-1.826 .827 .948 10.08 AS3153-57 4.430-4.450 3.451 3.572 20.68 AS3153-16 1.868-1.888 .889 1.010 10.33 AS3153-58 4.493-4.513 3.514 3.635 20.93 AS3153-17 1.930-1.950 .951 1.072 10
12、58 AS3153-59 4.556-4.576 3.577 3.698 21.19 AS3153-18 1.993-2.013 1.014 1.135 10.84 AS3153-60 4.618-4.638 3.639 3.760 21.43 AS3153-19 2.056-2.076 1.077 1.198 11.09 AS3153-61 4.680-4.700 3.701 3.822 21.68 AS3153-20 2.118-2.138 1.139 1.260 11.33 AS3153-62 4.743-4.763 3.764 3.885 21.94 AS3153-21 2.180-
13、2.200 1.201 1.322 11.59 AS3153-63 4.806-4.826 3.827 3.948 22.19 AS3153-22 2.243-2.263 1.264 1.385 11.84 AS3153-64 4.868-4.888 3.889 4.010 22.44 AS3153-23 2.306-2.326 1.327 1.448 12.10 AS3153-65 4.930-4.950 3.951 4.072 22.69 AS3153-24 2.368-2.388 1.389 1.510 12.34 AS3153-66 4.993-5.013 4.014 4.135 22
14、95 AS3153-25 2.430-2.450 1.451 1.572 12.60 AS3153-67 5.056-5.076 4.077 4.198 23.20 AS3153-26 2.493-2.513 1.514 1.635 12.85 AS3153-68 5.118-5.138 4.139 4.260 23.45 AS3153-27 2.556-2.576 1.577 1.698 13.11 AS3153-69 5.180-5.200 4.201 4.322 23.70 AS3153-28 2.618-2.638 1.639 1.760 13.36 AS3153-70 5.243-
15、5.263 4.264 4.385 23.96 AS3153-29 2.680-2.700 1.701 1.822 13.61 AS3153-71 5.306-5.326 4.327 4.448 24.21 AS3153-30 2.743-2.763 1.764 1.885 13.86 AS3153-72 5.368-5.388 4.389 4.510 24.45 AS3153-31 2.806-2.826 1.827 1.948 14.12 AS3153-73 5.430-5.450 4.451 4.572 24.71 AS3153-32 2.868-2.888 1.889 2.010 14
16、36 AS3153-74 5.493-5.513 4.514 4.635 24.96 AS3153-33 2.930-2.950 1.951 2.072 14.61 AS3153-34 2.993-3.013 2.014 2.135 14.87 AS3153-35 3.056-3.076 2.077 2.198 15.12 AS3153-36 3.118-3.138 2.139 2.260 15.38 AS3153-37 3.180-3.200 2.201 2.322 15.62 AS3153-38 3.243-3.263 2.264 2.385 15.88 AS3153-39 3.306-
17、3.326 2.327 2.448 16.13 AS3153-40 3.368-3.388 2.389 2.510 16.39 AS3153-41 3.430-3.450 2.451 2.572 16.63 AS3153-42 3.493-3.513 2.514 2.635 16.89 AS3153-43 3.556-3.576 2.577 2.698 17.14 AS3153-44 3.618-3.638 2.639 2.760 17.40 AEROSPACE STANDARD AS3153SHEET 3 OF 3REV. ABOLT, MACHINE - DOUBLE HEXAGON EX
18、TENDED WASHER HEAD, CLOSE TOLERANCE SHANK, AMS4967 (UNS R56400), 160 KSI, .5625-18, UNJF-3A NOTES: /1/ FOR PART NUMBERS AS3153-03 THRU AS3153-15 THE THREAD PD SHALL REPLACE DATUM B. 2. MATERIAL: TITANIUM ALLOY AMS4967 (SIMILAR TO UNS R56400) 3. PROCUREMENT SPECIFICATION: AS7461 4. FLUORESCENT PENETR
19、ANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra . 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. /8/
20、 HEAD TO SHANK FILLET SHALL BE COLD ROLLED PER AS7461 AFTER HEAT TREATMENT. THE COLD ROLLING SHALL BE SUFFICIENT TO REMOVE ALL VISUAL EVIDENCE OF GRINDING OR TOOL MARKS EXCEPT THAT DISTORTIONS AT “A” IN FIGURE 2 OF THE SPECIFICATION SHALL NOT BE PERMITTED ON THE HEAD BEARING AREA AND SHALL BE PERMIT
21、TED ON THE SHANK DIAMETER ONLY IF THE DISTORTION DOES NOT CAUSE THE SHANK DIAMETER TO EXCEED .5625 DIAMETER. 9. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982 (ASME PUBLICATION) 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER
22、 IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION
