1、 AEROSPACE STANDARD BOLT, MACHINE HEXAGON HEAD, PD SHANK UNS NO7718, 185 KSI MIN, .3750-24 UNJF-3A (STRESS RUPTURE RESISTANT) AS3416Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any
2、means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.or
3、g ISSUED1985-12REVISED2017-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.B FEDERAL SUPPLY CLASS 5306 AS3416 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS7467 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneering sciences. The useof this repo
4、rt is entirely voluntary, and its applicability and suitability for any particularuse, includingany patent infringement arisingtherefrom,is thesole responsibility of thHXVHU SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled.
5、SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS3416B RATIONALE UPDATE STRAIGHTNESS FCF, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING. ADD AS3062, ADD SURFACE TEXTURE REQUIREMENT TO WRENCH F
6、LATS, ADD RUNOUT REQUIREMENT TO EDGE OF BEARING SURFACE, ADD EXISTING INVENTORY USE NOTE, UPDATE FPI REQUIREMENT, FIGURE 1 RE-DRAWN, GENERAL EDITORIAL UPDATE. FIGURE 1 BOLT AEROSPACE STANDARD AS3416 SHEET 2 OF 3 REV. B BOLT, MACHINE HEXAGON HEAD, PD SHANK UNS NO7718, 185 KSI MIN, .3750-24 UNJF-3A (S
7、TRESS RUPTURE RESISTANT) TABLE 1 - DIMENSIONS L, G, K, AND APPROX. MASS PART NUMBER L G MIN K MAX APPROX MASS LBS/100 AS3416-03 AS3416-04 AS3416-05 AS3416-06 AS3416-07 AS3416-08 AS3416-09 AS3416-10 AS3416-11 AS3416-12 AS3416-13 AS3416-14 AS3416-15 AS3416-16 AS3416-17 AS3416-18 AS3416-19 AS3416-20 AS
8、3416-21 AS3416-22 AS3416-23 AS3416-24 AS3416-25 AS3416-26 AS3416-27 AS3416-28 AS3416-29 AS3416-30 AS3416-31 AS3416-32 AS3416-33 AS3416-34 AS3416-35 AS3416-36 AS3416-37 AS3416-38 AS3416-39 AS3416-40 AS3416-41 AS3416-42 .552- .572 .615- .635 .678- .698 .740- .760 .802- .822 .865- .885 .928- .948 .990-
9、1.010 1.052-1.072 1.115-1.135 1.178-1.198 1.240-1.260 1.302-1.322 1.365-1.385 1.428-1.448 1.490-1.510 1.552-1.572 1.615-1.635 1.678-1.698 1.740-1.760 1.802-1.822 1.865-1.885 1.928-1.948 1.990-2.010 2.115-2.135 2.240-2.260 2.365-2.385 2.490-2.510 2.615-2.635 2.740-2.760 2.865-2.885 2.990-3.010 3.115-
10、3.135 3.240-3.260 3.365-3.385 3.490-3.510 3.615-3.635 3.740-3.760 3.865-3.885 3.990-4.010 .025 .025 .025 .025 .025 .025 .025 .025 .025 .025 .045 .107 .169 .232 .295 .357 .419 .482 .545 .607 .669 .732 .795 .857 .982 1.107 1.232 1.357 1.482 1.607 1.732 1.857 1.982 2.107 2.232 2.357 2.482 2.607 2.732 2
11、857 .108 .108 .108 .108 .108 .108 .108 .108 .108 .125 .188 .250 .312 .375 .438 .500 .562 .625 .688 .750 .812 .875 .938 1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.05 3.23 3.40 3.58 3.76 3.93 4.11 4.28 4.46 4.64 4.81 4.99 5.17 5.35 5.53 5.7
12、0 5.88 6.05 6.23 6.41 6.58 6.76 6.93 7.11 7.46 7.81 8.18 8.53 8.88 9.23 9.58 9.94 10.29 10.64 11.00 11.35 11.70 12.06 12.41 12.76 AEROSPACE STANDARD AS3416 SHEET 3 OF 3 REV. B BOLT, MACHINE HEXAGON HEAD, PD SHANK UNS NO7718, 185 KSI MIN, .3750-24 UNJF-3A (STRESS RUPTURE RESISTANT) TABLE 1 - DIMENSIO
13、NS L, G, K, AND APPROX. MASS (CONTINUED) PART NUMBER L G MIN K MAX APPROX MASS LBS/100 AS3416-43 AS3416-44 AS3416-45 AS3416-46 AS3416-47 AS3416-48 AS3416-49 AS3416-50 AS3416-51 AS3416-52 4.115-4.135 4.240-4.260 4.365-4.385 4.490-4.510 4.615-4.635 4.740-4.760 4.865-4.885 4.990-5.010 5.115-5.135 5.240
14、5.260 2.982 3.107 3.232 3.357 3.482 3.607 3.732 3.857 3.982 4.107 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 13.11 13.46 13.83 14.18 14.53 14.88 15.23 15.59 15.94 16.29 AS3416-53 AS3416-54 AS3416-55 AS3416-56 AS3416-57 AS3416-58 5.365-5.385 5.490-5.510 5.615-5.635 5.740-5.760 5.865
15、5.885 5.990-6.010 4.232 4.357 4.482 4.607 4.732 4.857 4.375 4.500 4.625 4.750 4.875 5.000 16.65 17.00 17.36 17.71 18.06 18.41 NOTES 1. FOR PART NUMBERS AS3416-03 THROUGH AS3416-21 DATUM A SHALL REPLACE DATUM B. 2. MATERIAL: CORROSION AND HEAT RESISTANT NICKEL ALLOY AMS5662 (UNS N07718). 3. PROCUREM
16、ENT SPECIFICATION: AS7467 EXCEPT ROLL THREAD AND COLD WORK FILLET RADIUS AFTER PRECIPITATION HARDENING. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E 1417/E1417M TYPE 1, SENSITIVITY LEVEL 2 MINIMUM. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1 UNLESS OTHERWISE SPECIFIED
17、 SURFACES TO BE 125 MICROINCHES Ra EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE STATED. 7. DIMENSIONS ARE IN INCHES. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED
18、TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISION
19、S, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL REVISIONS ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
