1、 AEROSPACE STANDARD BOLT, MACHINE,DOUBLE HEX, EXT WASHER HEAD, CLOSE TOL. SHANK, UNS N07718, 185 KSI MIN .3125-24 UNJF-3A (STRESS RUPTURE RESISTANT) AS3419Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted,
2、 in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB AD
3、DRESS: http:/www.sae.org ISSUED1985-12REAFFIRMED 2006-05REVISED2017-04THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.C FEDERAL SUPPLY CLASS 5306 AS3419 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: AS7467 /3/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance th
4、estate of technicaland engineering sciences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at wh
5、ichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS3419C RATIONALE DELETE RADIUS AT TRANSITION OF WRENCH FLATS AND BASE FLANGE,
6、UPDATE FEATURE CONTROL FRAME FOR STRAIGHTNESS, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING, ADD SURFACE TEXTURE REQUIREMENTS FOR HEAD, WRENCH FLATS AND BOLT END, ADD NEW NOTE FOR DISPOSITION OF EXISTING INVENTORY, UPDATE FPI REFERENCE AND ADD STANDARD SENSITIVITY REQUIREMENT, FIGURE 1 RE-DRAWN, AND
7、 GENERAL EDITORIAL CHANGES. FIGURE 1 - BOLT AEROSPACE STANDARD AS3419 SHEET 2 OF 3 REV. C BOLT, MACHINE,DOUBLE HEX, EXT WASHER HEAD, CLOSE TOL. SHANK, UNS N07718, 185 KSI MIN .3125-24 UNJF-3A (STRESS RUPTURE RESISTANT) TABLE 1 - PART NUMBERS, DIMENSIONS L, G, K, AND APPROX MASS PART NUMBER L .010 G
8、MIN K MAX APPROX MASS LB/100 PART NUMBER L .010 G MIN K MAX APPROX MASS LB/100 AS3419-03 AS3419-04 AS3419-05 AS3419-06 AS3419-07 AS3419-08 AS3419-09 AS3419-10 AS3419-11 AS3419-12 AS3419-13 AS3419-14 AS3419-15 AS3419-16 AS3419-17 AS3419-18 AS3419-19 AS3419-20 AS3419-21 AS3419-22 AS3419-23 AS3419-24 A
9、S3419-25 AS3419-26 AS3419-27 AS3419-28 AS3419-29 AS3419-30 AS3419-31 AS3419-32 AS3419-33 AS3419-34 AS3419-35 AS3419-36 AS3419-37 AS3419-38 AS3419-39 AS3419-40 AS3419-41 AS3419-42 AS3419-43 AS3419-44 AS3419-45 AS3419-46 AS3419-47 AS3419-48 AS3419-49 AS3419-50 AS3419-51 AS3419-52 .751 .813 .875 .938 1
10、001 1.063 1.125 1.188 1.251 1.313 1.375 1.438 1.501 1.563 1.625 1.688 1.751 1.813 1.875 1.938 2.001 2.063 2.125 2.188 2.251 2.313 2.375 2.438 2.501 2.563 2.625 2.688 2.751 2.813 2.875 2.938 3.001 3.063 3.125 3.188 3.251 3.313 3.375 3.438 3.501 3.563 3.625 3.688 3.751 3.813 .105 .167 .229 .292 .355
11、417 .479 .542 .605 .667 .729 .792 .855 .917 .979 1.042 1.105 1.167 1.229 1.292 1.355 1.417 1.479 1.542 1.605 1.667 1.729 1.792 1.855 1.917 1.979 2.042 2.105 2.167 2.229 2.292 2.355 2.417 2.479 2.542 2.605 2.667 2.729 2.792 2.855 2.917 2.979 3.042 3.105 3.167 .198 .260 .322 .385 .448 .510 .572 .635
12、698 .760 .822 .885 .948 1.010 1.072 1.135 1.198 1.260 1.322 1.385 1.448 1.510 1.572 1.635 1.698 1.760 1.822 1.885 1.948 2.010 2.072 2.135 2.198 2.260 2.322 2.385 2.448 2.510 2.572 2.635 2.698 2.760 2.822 2.885 2.948 3.010 3.072 3.135 3.198 3.260 2.69 2.83 2.97 3.11 3.25 3.40 3.53 3.68 3.82 3.96 4.1
13、0 4.24 4.38 4.52 4.66 4.80 4.95 5.08 5.22 5.37 5.51 5.65 5.79 5.93 6.07 6.21 6.35 6.49 6.64 6.78 6.92 7.06 7.20 7.34 7.48 7.62 7.76 7.91 8.04 8.19 8.33 8.47 8.61 8.75 8.89 9.03 9.17 9.32 9.46 9.60 AS3419-53 AS3419-54 AS3419-55 AS3419-56 AS3419-57 AS3419-58 AS3419-59 AS3419-60 AS3419-61 AS3419-62 AS3
14、419-63 AS3419-64 AS3419-65 AS3419-66 AS3419-67 AS3419-68 AS3419-69 AS3419-70 AS3419-71 AS3419-72 AS3419-73 AS3419-74 AS3419-75 AS3419-76 AS3419-77 AS3419-78 AS3419-79 AS3419-80 AS3419-81 AS3419-82 3.875 3.938 4.001 4.063 4.125 4.188 4.251 4.313 4.375 4.438 4.501 4.563 4.625 4.688 4.751 4.813 4.875 4
15、938 5.001 5.063 5.125 5.188 5.251 5.313 5.375 5.438 5.501 5.563 5.625 5.688 3.229 3.292 3.355 3.417 3.479 3.542 3.605 3.667 3.729 3.792 3.855 3.917 3.979 4.042 4.105 4.167 4.229 4.292 4.355 4.417 4.479 4.542 4.605 4.667 4.729 4.792 4.855 4.917 4.979 5.042 3.322 3.385 3.448 3.510 3.572 3.635 3.698 3
16、760 3.822 3.885 3.948 4.010 4.072 4.135 4.198 4.260 4.322 4.385 4.448 4.510 4.572 4.635 4.698 4.760 4.822 4.885 4.948 5.010 5.072 5.135 9.74 9.88 10.02 10.16 10.30 10.44 10.58 10.72 10.86 11.00 11.15 11.29 11.43 11.57 11.71 11.85 11.99 12.13 12.28 12.42 12.56 12.70 12.84 12.98 13.12 13.26 13.40 13.
17、54 13.68 13.83 AEROSPACE STANDARD AS3419 SHEET 3 OF 3 REV. C BOLT, MACHINE,DOUBLE HEX, EXT WASHER HEAD, CLOSE TOL. SHANK, UNS N07718, 185 KSI MIN .3125-24 UNJF-3A (STRESS RUPTURE RESISTANT) NOTES /1/ FOR PART NUMBERS AS3419-03 THROUGH AS3419-08, DATUM A SHALL REPLACE DATUM B. 2. MATERIAL: CORROSION
18、AND HEAT RESISTANT NICKEL ALLOY AMS5662 (UNS N07718). /3/ PROCUREMENT SPECIFICATION: AS7467, EXCEPT ROLL THREAD AND COLD WORK FILLET RADIUS AFTER PRECIPITATION HARDENING. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M.
19、 REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra, EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS ARE IN INCHES. 8. DIMENSIONS AND TOLERANCING ANSI Y14.5M-1982 (ASME PUBLICATION). 9. U
20、NLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING, OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENC
21、E OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
