1、 AEROSPACE STANDARD CONNECTOR, PLUG, ELECTRIC, SOLDER CONTACT, UTILITY AS34361Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording
2、 or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-06REVISED REAFFIRMED 2017-03THIRD ANGLE P
3、ROJECTION CUSTODIAN: AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935 AS34361 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: AS50151 SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportisentirely voluntary, a
4、nd its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleastevery five years at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your written c
5、omments and suggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS34361A RATIONALE AS34361A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST
6、 OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS50151. FIGURE 1 CONNECTOR CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS34361 SHEET 2 OF 2 REV. A CONNECTOR, PLUG, ELECTRIC, SOLDER CONTACT, UTILITY REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE
7、OF AS50151. 1. DESIGN CONNECTORS AND ACCESSORIES SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1. DIMENSIONS ARE IN INCHES. TOLERANCES IN ACCORDANCE WITH ASME-Y14.5 -DIMENSIONING AND TOLERANCING. THERE SHALL BE A MINIMUM OF 8 GROUNDING SPRINGS PER INCH. THE GROUNDING LUG SHALL BE INSTALLED ADJACENT TO
8、 PIN “D”. THE CONNECTOR SHALL MEET ALL REQUIREMENTS OF AS50151 EXCEPT WHERE MODIFIED FOR SPECIAL GROUNDING FUNCTIONS. THE CABLE CLAMP SHALL COMFORM TO AS85049/41-12A. 2. MATERIAL GROUNDING SPRINGS-BERYLIUM COPPER. 3. FINISH SHELL AND ACCESSORIES-OLIVE DRAB CHROMATE COATING OVER CADMIUM PLATE. 4. THE
9、 PART NUMBER SHALL BE AS SHOWN IN THE EXAMPLE BELOW: CONNECTOR PART NUMBER: MS3436 A 20 - 4 S BASIC PART NUMBER CLASS SIZE INSERT ARRANGEMENT CONTACT STYLE (P OR S) NOTES NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTION
10、S CONCERNING CADMIUMS USE. APPLICATION NOTES AS34361 IS NOT RECOMMENDED FOR NEW DESIGN AND IS NO LONGER RECOMMEDED FOR USE, EXCEPT FOR REPLACEMENT PURPOSES. SPECIFICATION NOTES A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS,
11、 NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
