1、 AEROSPACE STANDARD FITTING, ELBOW, 45, EXTERNAL THREAD, BEAM SEAL TO INTEGRAL WELD RING AS4230Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoc
2、opying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1996-05REVISED 2007-09 REAFF
3、IRMED 2015-04THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730AS4230 SHEET 1 OF 4 REV. C PROCUREMENT SPECIFICATION: /5/ AS4510SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofth
4、isreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelle
5、d. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4230C RATIONALE AS4230C HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 - FITTING, ELBOW, 45 AEROSP
6、ACE STANDARD AS4230 SHEET 2 OF 4 REV. C FITTING, ELBOW, 45, EXTERNAL THREAD, BEAM SEAL TO INTEGRAL WELD RING TABLE 1A - DIMENSIONS BASIC NO. AS4230 /16/ SIZE AND TUBE WALL CODES RANGE OF NOMINAL TUBE WALL FOR PORT #2 /7/ /16/ (NOMINALTUBE SIZE) PORT #1STYLE /10/ T THREAD PER AS8879 CLASS 3A A B C D
7、/10/ 03-018 03-022 04-022 05-022 05-028 06-022 06-028 06-032 08-022 08-043 10-028 10-043 10-055 12-028 12-055 12-065 14-032 14-065 16-043 16-078 16-089 20-055 20-089 24-055 .016-.018 .019-.022 .019-.022 .019-.022 .023-.028 .019-.022 .023-.028 .029-.032 .019-.022 .033-.043 .023-.028 .033-.043 .044-.0
8、55 .023-.028 .044-.055 .056-.065 .029-.032 .056-.065 .033-.043 .066-.078 .079-.089 .044-.055 .079-.089 .044-.055 .188 .188 .250 .312 .312 .375 .375 .375 .500 .500 .625 .625 .625 .750 .750 .750 .875 .875 1.000 1.000 1.000 1.250 1.250 1.500 A A B B B B B B B B B B A B A A B A B A A B A B .3750-28 UNJS
9、.3750-28 UNJS.4375-24 UNJS.5000-24 UNJS.5000-24 UNJS.5625-20 UNJS.5625-20 UNJS.5625-20 UNJS.7188-20 UNJS.7188-20 UNJS.8438-18 UNJS.8438-18 UNJS.8438-18 UNJS1.0000-16 UNJ 1.0000-16 UNJ 1.0000-16 UNJ 1.1250-16 UNJ 1.1250-16 UNJ 1.2500-14 UNJS1.2500-14 UNJS1.2500-14 UNJS1.5781-14 UNJS1.5781-14 UNJS1.84
10、38-14 UNJS.832.832.832.887.8871.0051.0051.0051.1801.1801.2431.2431.2431.3921.3921.3921.5621.5621.6171.6171.6171.7501.7501.900.378 .378 .420 .438 .438 .471 .471 .471 .528 .528 .619 .619 .619 .685 .685 .685 .753 .753 .783 .783 .783 .836 .836 1.003 .610 .610 .680 .650 .650 .740 .740 .740 .820 .820 .880
11、 .880 .880 .980 .980 .980 1.090 1.090 1.150 1.150 1.150 1.170 1.170 1.270 .146.138.200.262.250.325.313.305.450.408.563.533.509.688.634.614.805.739.908.838.8161.1341.0661.384AEROSPACE STANDARD AS4230 SHEET 3 OF 4 REV. C FITTING, ELBOW, 45, EXTERNAL THREAD, BEAM SEAL TO INTEGRAL WELD RING TABLE 1B - D
12、IMENSIONS AND WEIGHTS BASIC NO. AS4230 /16/ SIZE AND TUBE WALL CODES E /10/ F .005 G MIN V W RECOMMENDED MAXIMUM PRESSURE PSI /7/ LB/EA MAX CRES LB/EA MAX TI 03-018 03-022 04-022 05-022 05-028 06-022 06-028 06-032 08-022 08-043 10-028 10-043 10-055 12-028 12-055 12-065 14-032 14-065 16-043 16-078 16
13、-089 20-055 20-089 24-055 - - .184- .194 .232- .242 .232- .242 .297- .307 .297- .307 .297- .307 .398- .408 .398- .408 .512- .523 .512- .523 - .649- .660 - - .769- .780 - .862- .874 - - 1.115-1.128 - 1.324-1.337 .080 .080 .080 .080 .080 .090 .090 .090 .090 .090 .125 .125 .125 .125 .125 .125 .125 .125
14、 .125 .125 .125 .180 .180 .180 .285 .285 .329 .391 .391 .454 .454 .454 .547 .547 .673 .673 .673 .860 .860 .860 1.110 1.110 1.110 1.110 1.110 1.360 1.360 1.610 .360- .377 .360- .377 .360- .377 .423- .440 .423- .440 .485- .502 .485- .502 .485- .502 .547- .565 .547- .565 .673- .691 .673- .691 .673- .69
15、1 .860- .878 .860- .878 .860- .878 1.110-1.128 1.110-1.128 1.110-1.128 1.110-1.128 1.110-1.128 1.355-1.380 1.355-1.380 1.605-1.630 .055 .055 .060 .060 .060 .060 .060 .060 .065 .065 .070 .070 .070 .095 .095 .095 .105 .105 .110 .110 .110 .110 .110 .130 5000 5000 5000 4000 5000 3000 4000 5000 2000 5000
16、 2000 4000 5000 2000 4000 5000 2000 4000 2000 4000 5000 2000 4000 2000 .0175 .0175 .0204 .0300 .0300 .0388 .0388 .0388 .0592 .0592 .0874 .0874 .0874 .132 .132 .132 .234 .234 .239 .239 .239 .344 .344 .557 .0100 .0100 .0116 .0171 .0171 .0222 .0222 .0222 .0338 .0338 .0500 .0500 .0500 .0753 .0753 .0753
17、.134 .134 .136 .136 .136 .197 .197 .318 NOTES: /1/ MATERIAL: a. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR BAR PER AMS 4965. b. CODE LETTER P - TYPE 17-4PH CORROSION RESISTANT STEEL FORGING OR BAR PER AMS 5643. c. CODE LETTER V - TYPE 15-5PH CORROSION RESISTANT STEEL FORGING OR BAR PER AM
18、S 5659. 2. HEAT TREATMENT: a. MATERIAL CODE LETTER T - NONE. b. MATERIAL CODE LETTERS P AND V - HEAT TREAT TO CONDITION H 1075 PER AMS 2759/3. 3. FINISH: a. MATERIAL CODE LETTER T - NONE. b. MATERIAL CODE LETTER P AND V - PASSIVATE PER AMS 2700. AEROSPACE STANDARD AS4230 SHEET 4 OF 4 REV. C FITTING,
19、 ELBOW, 45, EXTERNAL THREAD, BEAM SEAL TO INTEGRAL WELD RING /4/ DRY FILM LUBRICANT: APPLY DRY FILM LUBRICANT PER AS5272, TYPE I TO THE SEALING SURFACE OF THE AS4207 FITTING END. OVERSPRAY IN BORE IS NOT PERMITTED. /5/ PROCUREMENT SPECIFICATION: AS4510 EXCEPT AS SPECIFIED ON THIS STANDARD. THIS PART
20、 SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE ASSEMBLY. THE AS4207 FITTING END SHALL HAVE BEEN QUALIFIED TO THE APPLICABLE REQUIREMENTS OF AS85421 OR AS85720. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS. /6/
21、 IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3, OR 15B. MANUFACTURERS IDENTIFICATION, CAGE CODE NUMBER OR TRADEMARK, BASIC NUMBER, MATERIAL CODE LETTER, AND TUBE WALL CODE. /7/ THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES SHOWN IN TAB
22、LE 1 WITH THE RECOMMENDATION THAT THE MINIMUM WALL THICKNESS OF THE TUBING WELDED TO THE AS4697 FITTING END OF PORT #2 BE THE VALUE SHOWN FOR THE APPROPRIATE OPERATING PRESSURE IN ARP4698. THINNER WALL THICKNESSES MAY BE USED. 8. WHEN MACHINED FROM BAR OR OVERSIZED FORGINGS, THE CENTER BODY SECTION
23、SHALL CONFORM TO AS1376, TABLE 4. /9/ .030 TO .125 RADIUS UNLESS QUALIFICATION OF SPECIAL PROCESS WITH SMALLER RADIUS. APPLICABLE FOR TITANIUM ALLOY PARTS ONLY. /10/ IF PORT #1 IS STYLE A, D WILL EXTEND THE ID LENGTH AND E WILL NOT APPLY. 11. INTERPRETATION OF DRAWING PER ARP4296. 12. SURFACE TEXTUR
24、E: SYMBOLS PER ANSI Y14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra. 13. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 14. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994 15. DIMENSIONS IN INCHES. UNLESS
25、OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .015, ANGULAR DIMENSIONS 2. /16/ EXAMPLE OF PART NUMBER: 17. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.
