1、 AEROSPACE STANDARD FITTING, TEE, FLARED TUBE, INTERNAL THREAD ON RUN, FOR SEAL RING AS4310Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyi
2、ng, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1993-08REAFFIRMED 2007-09REVISED
3、 2015-03THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730AS4310 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: /4/ KSC-F-124SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis
4、report is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled.
5、 SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4310A 04 .250 .4375-20UNJF .4375-20UNJF 1.797 .797 1.235 .75006 .375 .5625-18UNJF .5625-18UNJF 2.047 .860 1.297 .87508 .500 .7500-
6、16UNJF .7500-16UNJF 2.203 1.047 1.485 1.06310 .625 .8750-14UNJF .8750-14UNJF 2.422 1.203 1.672 1.18812 .750 1.0625-12UNJ 1.0625-12UNJ 2.672 1.391 1.860 1.43816 1.000 1.3125-12UNJ 1.3125-12UNJ 2.891 1.578 2.110 1.68820 1.250 1.6250-12UNJ 1.6250-12UNJ 3.078 1.766 2.297 2.000T2 THREAD PER AS8879 CLASS
7、3BA +.000 -.047DBASIC NUMBER AS4310 /17/ SIZE CODE(NOMINAL TUBE SIZE)T1 THREAD PER AS8879 CLASS 3AB +.000 -.047C +.000 -.047RATIONALE CORRECTED END 1 TO STYLE “S” AND END 2 TO STYLE “E” IN FIGURE 1. ADDED NOTES /14/ AND /15/, UPDATED NOTE /4/ TO INCLUDE THE NADCAP SCOPE AC7112, AC7112/2. ADDED “FITT
8、ING” TO TITLE BLOCK. FIGURE 1 - TEE, FLARED TUBE, INTERNAL THREAD ON RUN TABLE 1 - DIMENSIONS AEROSPACE STANDARD AS4310 SHEET 2 OF 3 REV. A FITTING, TEE, FLARED TUBE, INTERNAL THREAD ON RUN, FOR SEAL RING 04 .250 .906 1.188 .750 .101 .28006 .375 1.031 1.281 .875 .143 .39508 .500 1.250 1.469 1.063 .2
9、35 .65210 .625 1.469 1.750 1.063 .253 .70212 .750 1.750 1.875 1.313 .417 1.16016 1.000 2.063 2.094 1.625 .663 1.84020 1.250 2.313 2.250 1.875 .906 2.510LB/EA APPROX REF ALUMBASIC NUMBER AS4310 /17/ SIZE CODE(NOMINAL TUBE SIZE)LB/EA APPROX REF CRESJ +.047 -.000 V /8/ K +.047 -.000 TABLE 2 - DIMENSION
10、S AND WEIGHTS NOTES: /1/ MATERIAL: a. CODE LETTER D: TYPE 2014-T6 ALUMINUM ALLOY FORGING PER AMS4133 OR AMS-QQ-A-367; OR 2024-T6 OR 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS-QQ-S-763. b. CODE LETTER J: 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS5639. c. CODE LET
11、TER K: 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS5648. d. CODE LETTER R: 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS5645. e. CODE LETTER S: 347 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS5646. 2. HEAT TREAT PER PROCUREMENT SPECI
12、FICATION. 3. FINISH: a. MATERIAL CODE LETTER D: ANODIZE PER AMS2472 OR MIL-A-8625 TYPE II, CLASS 2, COLOR BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. b. CORROSION RESISTANT STEEL: PASSIVATE PER AMS2700, TYPE 6 OR 7. 4. PROCUREMENT SPECIFICATION: KSC-F-124 - JOHN F KENNEDY SPACE CENTER, NASA, SP
13、ECIFICATION FOR FITTINGS (PRESSURE CONNECTIONS), FLARED TUBE. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) QUALIFIED MANUFACTURERS LIST (QML) AC7112, AC7112/2 FOR SIM
14、ILAR FLARED FITTINGS. THE QML IS AVAILABLE AT www.eAuditN. /5/ IDENTIFICATION: MARK PER AS478-7A3, -15A3, -15B, CLASS C OR CLASS D a. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER. b. FOR SIZES 08 (.500 OD TUBE SIZE) A
15、ND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. /6/ .125 MINIMUM DIMENSION APPLIES ONLY WHEN D IS GREATER THAN THE V DIMENSION. /7/ THE SEAL RING IS ORDERED SEPARATELY AS AN AS1097. AEROSPACE STANDARD AS4310 SHEET 3 OF 3 REV. A FITTING, TEE, FLARED
16、TUBE, INTERNAL THREAD ON RUN, FOR SEAL RING /8/ WHEN MACHINING FROM BAR STOCK OR OVERSIZED FORGING, THE CENTER BODY DIMENSION SHALL CONFORM TO AS1376, TABLE 2. 9. INTERPRETATION OF DRAWING PER AS4296. 10. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIF
17、IED, MACHINED SURFACES ARE TO BE 125 MICROINCHES Ra. 11. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 12. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982 13. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 030. 14. INVENTORIED PARTS CON
18、FORMING TO PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION. 15. THE SHOULDER IS NOT NEEDED BECAUSE THE FORGING BODY SIZE IS DESIGNED TO ACCOMMODATE THE INTERNAL BOSS PORT END, WHICH REQUIRES A LARGER BODY AND WALL THICKNESS. TO SEE HOW THE SHOULDER IS USED REFER TO AS1033 AS1038 AND AS1040. 16. A CH
19、ANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 17. EXAMPLE OF PART NUMBER: AS4310 K 08 BASIC PART NUMBER MATERIAL CODE LETTER /1/ TUBE SIZE IN .062 INCHES INCREMENTS (08 = .500)
