1、AEROSPACE STANDARD HOSE ASSEMBLY, LINED SILICONE, 125 PSI, FIXED CAVITY COUPLING, POTABLE WATER,STRAIGHT MALE TO 45 FEMALE AS4802Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any mea
2、ns, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org I
3、SSUED 1993-06REAFFIRMED 2007-01 REVISED 2010-11THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3D REV.CFEDERAL SUPPLY CLASS 4720 AS4802SHEET 1 OF 2REV. CPROCUREMENT SPECIFICATION: AS4468 /2/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandeng
4、ineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirme
5、d, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4802CRATIONALE CORRECTED “MATES WITH” REFERENCE. FIGURE 1 - HOSE ASSEMBLY TABLE 1 - BASIC HOSE AND END FIT
6、TING DIMENSIONS BASIC NO. ANDSIZE CODE HOSE SIZE(REF) AMAXB(REF) CMAXDMINDMAXID(REF) OD MINOD MAXAS4802-08 .500 1.40 .425 1.81 .66 .74 .500 .65 .73 AS4802-10 .625 1.40 .550 1.93 .69 .76 .625 .81 .85 AS4802-12 .750 1.53 .654 2.45 .87 .94 .750 .94 .98 AS4802-16 1.000 1.73 .909 2.60 .96 1.04 1.000 1.19
7、 1.23 TABLE 2 - LENGTH TOLERANCE HOSE ASSEMBLY LENGTH PREFERRED INCREMENTS TOLERANCE UNDER 18 IN (NOT LESS THAN) .125 +.125/-.125 18 TO 36 IN EXCLUSIVE (NOT LESS THAN) .250 +.250/-.250 36 TO 100 IN EXCLUSIVE (NOT LESS THAN) .500 +.375/-.375 100 IN AND OVER (NOT LESS THAN) 1.000 +.5%/-.500 TABLE 3 -
8、HOSE ASSEMBLY WEIGHT INFORMATION HOSE SIZECODE HOSE LB/INNOM (REF) END FITTING LB/EASTRAIGHT NOM (REF) END FITTING LB/EA45 NOM (REF) HOSE LENGTH CORRECTION FACTOR, INCH /9/ STRAIGHT HOSE LENGTH CORRECTION FACTOR, INCH /9/ 45 08 .0081 .038 .066 .70 1.19 10 .0111 .047 .086 .70 1.30 12 .0137 .083 .139
9、.75 1.67 16 .0182 .118 .188 .80 1.81 AEROSPACE STANDARD AS4802SHEET 2 OF 2REV. CHOSE ASSEMBLY, LINED SILICONE, 125 PSI, FIXED CAVITY COUPLING, POTABLE WATER, STRAIGHT MALE TO 45 FEMALE NOTES: 1. MATERIAL AND FINISH: PER AS4468, TABLE 1. ALL FITTING COMPONENTS 300 SERIES CORROSION RESISTANT STEEL, PA
10、SSIVATED./2/ PROCUREMENT SPECIFICATION: AS4468 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED AND ASSEMBLED BY AN ACCREDITED MANUFACTURER OR ASSEMBLED BY AN ACCREDITED DISTRIBUTOR LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS
11、LIST (QPL) PRI QPL AS4468 FOR THIS STANDARD. SEE FOR CURRENT QPL ON LINE. 3. INTENDED USE: THESE HOSE ASSEMBLIES ARE INTENDED FOR USE IN POTABLE WATER SYSTEM INSTALLATIONS WHERE A HIGH DEGREE OF FLEXIBILITY IS REQUIRED. 4. IDENTIFICATION: PER AS4468. 5. OPERATING CHARACTERISTICS: a. OPERATING TEMPE
12、RATURE: -65 TO +160 F (-54 TO +71 C). b. OPERATING PRESSURE: 125 PSI MAX 6. FUNCTIONAL TEST AND CLEANING: PER AS4468. 7. CONSTRUCTION: PER AS4468. /8/ LENGTH “L” IS A FOUR-DIGIT NUMBER OF WHICH THE FIRST THREE DIGITS DESCRIBE THE HOSE ASSEMBLY LENGTH IN WHOLE INCHES, AND THE FOURTH DIGIT THE FRACTIO
13、N OF AN INCH IN EIGHTHS. LENGTH “L” IS MEASURED FROM “GAGE POINT” TO “GAGE POINT”. SEE TABLE 2 FOR LENGTH TOLERANCES. /9/ HOSE WEIGHT PLUS EACH END FITTING WEIGHT EQUALS HOSE ASSEMBLY WEIGHT. FOR DETERMINING HOSE WEIGHT, DEDUCT APPROPRIATE LENGTH CORRECTION FACTOR FROM EACH END OF THE ASSEMBLY LENGT
14、H. 10. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 11. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 2 DEGREES. 12. EXAMPLE OF PART NUMBER: AS4802 - 08 - 024 2FRACTIONAL LENGTH IN EIGHTHS OF AN INCH INCREMENTS (.25 IN) /8/ LENGTH IN WHOL
15、E INCHES (24 IN) /8/ BASIC HOSE ASSEMBLY SIZE CODE (.5 IN HOSE SIZE) (SEE TABLE 1) BASIC PART NUMBER 13. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
