1、AEROSPACE STANDARD CRIMPING TOOL AND ACCESSORIES, INSPECTION GAGES, FOR AS5259 DIES AS5259/6Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopy
2、ing, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2012-02THIRD ANGLE PROJECTION C
3、USTODIAN: AE-8C2 FEDERAL SUPPLY CLASS 5120 AS5259/6SHEET 1 OF 4PROCUREMENT SPECIFICATION: AS5259SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability an
4、d suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, stabilized or cancelled.SAEinvites yourwrittencommentsandsuggestions. SAE
5、values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5259/6RATIONALE PROVIDE STANDARD INSPECTION GAGES TO REPLACE NONSTANDARD GAGES PROCURED BY USERS AND TO CONSOLIDATE ALL GAGES IN ONE SPECIFICATION. NOTICE THE REQUIREMENTS FOR PROCURI
6、NG THE TOOLS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF: SAE AS5259. FIGURE 1 INSPECTION GAGE FOR SINGLE INDENT DIE Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A
7、EROSPACE STANDARD AS5259/6SHEET 2 OF 4CRIMPING TOOL AND ACCESSORIES, INSPECTION GAGES, FOR AS5259 DIES TABLE 1 INSPECTION GAGE CONFIGURATION FOR FORM CRIMP DIES GAGE PART NOWIRESIZE(REF)AS5259/7 CRIMP DIES (REF)A+.0002 -.0000 B CHROME PLATE WITH ADEQUATE COVERAGE FOR CORROSION AND WEAR RESISTANCE PE
8、R AMS-QQ-C-320 PLATING CHROMIUM, CLASS I, TYPE II WITH A THICKNESS OF .00003 INCHES MINIMUM. GAGE HANDLE: ANODIZED IN ACCORDANCE WITH MIL-A-8625 OR EQUALIVALENT. 4. MARKING: STAMPING SHALL BE INDENTED. LASER ETCHING IS ACCEPTABLE. OTHER MARKINGS ARE PERMITTED. 5. STORAGE CONTAINER: EACH GAGE SHALL B
9、E FURNISHED WITH A SUITABLE CONTAINER. 6. PART NUMBER M5259/6 -001 I I_ GAGE DASH NUMBER (-001, -002, ETC.) I_ PART NUMBER DESIGNATION (M) AND DETAIL SPECIFICATION NUMBER (AS5259/) 1/ 1/ UNDER SAE GUIDELINES PREVIOUS MILITARY PART NUMBERS SHALL BE USED FOR MS25472, MS90486, AND MS23003 GAGES. APPLIC
10、ATION NOTES: 1. TOOL IS USED AS A GO/NO-GO VERIFICATION INSPECTION GAGE FOR VARIOUS AS5259 DIES SPECIFIED IN TABLE 1 AND 2. 2. MS25472, MS90486, AND MS23003 GAGES LISTED IN AS5259/1 HAVE BEEN MOVED TO THIS SPECIFICATION. PART NUMBERS REMAIN UNCHANGED. SPECIFICATION NOTES: 1. A CHANGE BAR (|) LOCATED
11、 IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
