1、AEROSPACE STANDARDFITTING ASSEMBLY, ADAPTERRING LOCKED PORT CONNECTION TO BEAM SEAL4000 PSI AND 5000 PSI /9/AS5986Copyright 2015 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic,
2、mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2005-07REVISED
3、2015-08THIRD ANGLE PROJECTIONCUSTODIAN: G-3/G-3BREV. DFEDERAL SUPPLY CLASS4730AS5986SHEET 1 OF 3REV.DPROCUREMENT SPECIFICATION: AS85720 /4/SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportisentir
4、ely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom,is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites y
5、our written comments and suggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5986DRATIONALEUPDATE OF MAXIMUM WEIGHT VALUES VERIFIED THROUGH CAD MODELING, AND UPDATE OF PASSIVATION AND DRAWING INTERPRETATION SPECIFICATIO
6、NS.FIGURE 1 - ADAPTER, ASSEMBLYTABLE 1A - DIMENSIONS A - FBASIC NO.AS5986/17/SIZE CODE(NOMINALTUBESIZE)ATHREADAS8879BTHREADAS8879 C D EF+.005/-.00202 .125 .3125-32UNJEF-3A .2160-28UNJF-3A .400 .265 - .271 .090 - .096 .15403 .188 .3750-28UNJS-3A .2500-28UNJF-3A .468 .323 - .329 .122 - .128 .18604 .25
7、0 .4375-24UNJS-3A .3125-24UNJF-3A .514 .377 - .383 .169 - .175 .23905 .312 .5000-24UNJS-3A .3750-24UNJF-3A .624 .440 - .446 .231 - .237 .30106 .375 .5625-20UNJS-3A .4375-20UNJF-3A .700 .490 - .497 .294 - .300 .36408 .500 .7188-20UNJS-3A .5625-18UNJF-3A .814 .646 - .654 .398 - .408 .48210 .625 .8438-
8、18UNJS-3A .6875-24UNJEF-3A 1.040 .763 - .772 .493 - .503 .62512 .750 1.0000-16UNJ-3A .8125-20UNJEF-3A 1.170 .910 - .919 .604 - .614 .73714 .875 1.1250-16UNJ-3A .9375-20UNJEF-3A 1.341 1.034 - 1.044 .729 - .739 .86816 1.000 1.2500-14UNJS-3A 1.1250-18UNJEF-3A 1.456 1.148 - 1.158 .839 - .851 1.00020 1.2
9、50 1.5781-14UNJS-3A 1.3125-18UNJEF-3A 1.782 1.476 - 1.486 1.073 - 1.086 1.22524 1.500 1.8438-14UNJS-3A 1.6250-18UNJEF-3A 2.031 1.741 - 1.751 1.307 - 1.320 1.502AEROSPACE STANDARD AS5986SHEET 2 OF 3REV.DFITTING ASSEMBLY, ADAPTERRING LOCKED PORT CONNECTION TO BEAM SEAL4000 PSI AND 5000 PSI /9/TABLE 1B
10、 - DIMENSIONS G - P AND WEIGHTBASIC NO.AS5986/17/SIZE CODEGMIN HJ+.010/-.005K.000/-.015L+.010/-.005M.007NMIN PWEIGHTLB/EAMAX02 .246 .317 .519 .300 .125 .192 .141 24 .00903 .278 .349 .550 .355 .125 .192 .164 26 .01204 .331 .400 .592 .355 .125 .192 .197 30 .01605 .393 .491 .592 .381 .125 .192 .197 36
11、.02106 .456 .544 .633 .395 .125 .210 .205 36 .02708 .574 .670 .646 .430 .125 .210 .218 40 .03810 .717 .824 .710 .465 .125 .210 .274 38 .06612 .891 .981 .760 .527 .157 .220 .303 40 .08814 1.022 1.118 .778 .572 .157 .220 .318 50 .11116 1.154 1.251 .808 .564 .157 .220 .338 36 .13720 1.379 1.466 .832 .5
12、69 .157 .240 .335 56 .19824 1.656 1.768 .917 .608 .157 .240 .420 81 .299NOTES:1. MATERIAL:a. FITTING: 6Al-4V TITANIUM ALLOY PER AMS4928, AMS4965, OR AMS4967.b. LOCKRING: A286 CORROSION RESISTANT STEEL PER AMS5731, AMS5732, AMS5734, AMS5737, OR AMS5853.2. HEAT TREATMENT:a. FITTING: 130 KSI UTS MIN.b.
13、 LOCKRING: 34-40 HRC.3. FINISH:a. FITTING: ANODIC TREATMENT PER AMS2488, TYPE 2. APPLY DRY FILM LUBRICANT PER AS5272, TYPE 1, TO SEALING SURFACE OF FITTING END AS85720/1 AND “A” THREAD ONLY. OVERSPRAY ON THREAD UNDERCUT PERMISSIBLE.b. LOCKRING: PASSIVATE PER AMS2700, TYPE 2 OR 8./4/ PROCUREMENT SPEC
14、IFICATION:a. AS85421 (SIZES 02, 03, 05, 14, 20, AND 24): PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS85421 FOR THIS STANDARD. SEE https:/www.eAuditN FOR CURRENT QP
15、L ONLINE.b. AS85720 (SIZES 04, 06, 08, 10, 12, AND 16): PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS85720 FOR THIS STANDARD. SEE https:/www.eAuditN FOR CURRENT QPL
16、 ONLINE./5/ SEALING SURFACE: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT./6/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT.AEROSPACE STANDARD AS5986SHEET 3 OF 3REV.DFITTING ASSEMBLY, ADAPTERRING LOCKED PORT CONNECTION TO BEAM SEAL4000 PSI AND 5000 PSI /9/7/ SEALING ANGLES:a. SIZES
17、 -02 AND -03: 3q00 TO 3q30b. SIZES -04 AND LARGER: 8q30 TO 9q00/8/ IDENTIFICATION: a. MARK AT LOCATION(S) SHOWN PER AS478 METHOD 2 OR 15, MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE.b. BAG AND TAG PER AS478, METHOD 35D, MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE AND PART NUMBER./9/ WORKING PRESSURE
18、: THIS PART IS DESIGNED FOR USE IN HYDRAULIC SYSTEMS COMPATIBLE WITH TITANIUM.a. SIZE -04, -06, -08, -10, -12, AND -16: 5000 PSI (20 000 PSI BURST PRESSURE) SYSTEMS.b. ALL OTHER SIZES: 4000 PSI (16 000 PSI BURST PRESSURE) SYSTEMS.10. ADAPTERS TO BE INSTALLED PER AS1301 INTO BOSS CAVITIES PER AS1300.
19、11. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT,
20、 INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.12. INTERPRETATION OF DRAWING PER AS4296.13. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SU
21、RFACES TO BE 125 MICROINCHES Ra AND SEALING SURFACE TO BE 63 MICROINCHES Ra.14. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.15. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.16. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 0q30./17/ EXAMPLE OF PART NUMBER:
