1、 AEROSPACE STANDARD CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, CRIMP CONTACTS, (QUADRUPLE INSERT, TYPE II, CLASS 1 (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) AS81659/43Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retriev
2、al system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: Customer
3、Servicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-05REVISED2017-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.B FEDERAL SUPPLY CLASS 5935 AS81659 /43 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS81659 SAE Technical Standards Board Rules provide that: “This report is published by
4、 SAEtoadvance thestate of technicaland engineering sciences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast ever
5、y fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS81659/43B RATIONALE REVISION IS REQUIRED TO UPDATE THE CONNE
6、CTOR INSERT AND INSTALLING/REMOVAL TOOL REFERENCES. INCH MM INCH MM INCHES MM INCHES MM INCHES MM .006 .040 .047 .050 .055 .060 .062 .065 0.15 1.016 1.19 1.27 1.40 1.52 1.57 1.65 .093 .117 .118 .122 .133 .178 .198 .281 2.36 2.97 3.00 3.10 3.38 4.52 5.03 7.14 .297 .521 .541 .928 .930 .948 1.367 1.387
7、 7.54 13.23 13.74 23.57 23.62 24.08 34.72 35.23 1.3915 1.427 1.447 1.634 1.648 1.860 2.413 2.485 2.505 35.34 36.25 36.75 41.50 41.86 47.24 61.21 63.12 63.62 2.783 3.060 3.090 3.296 3.595 3.625 3.645 3.845 3.875 70.69 77.72 78.49 83.72 91.31 92.08 92.58 97.66 98.42 FIGURE 1 SUGGESTED PANEL CUT-OUT DI
8、MENSIONS AEROSPACE STANDARD AS81659 /43 SHEET 2 OF 3 REV. B CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, CRIMP CONTACTS, (QUADRUPLE INSERT, TYPE II, CLASS 1 (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 CONNECTOR CONFIGURATIONS AND DIMENSIONS AEROSPACE STANDARD AS81659 /43 SHEET 3 OF
9、 3 REV. B CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, CRIMP CONTACTS, (QUADRUPLE INSERT, TYPE II, CLASS 1 (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 CONNECTOR CONFIGURATIONS AND DIMENSIONS (CONTINUED) REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST IS
10、SUE OF AS81659. 1. DESIGN: CONNECTOR ACCESSORIES SHALL BE DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM. NORMAL (01) POLARIZATION POSITION SHOWN, FOR ALTERNA
11、TE POSITIONS SEE AS81659. FOR LOCATION OF DATUMS G AND H, REFER TO AS81659 FIGURE 11. 2. INSERT ARRANGEMENTS SHALL BE IN ACCORDANCE WITH AS31571. 3. CONTACTS SHALL BE IN ACCORDANCE WITH AS39029/11 OR AS39029/12, AS APPLICABLE. 4. INSTALLING AND REMOVAL TOOLS SHALL BE IN ACCORDANCE WITH AS81969/1 OR
12、AS81969/14. SPECIFICATION NOTES: 1. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
