1、 AEROSPACE STANDARD CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE,CRIMP CONTACTS, (QUADRUPLE INSERT, TYPE III, CLASS 1,(-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) AS81659/64Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retriev
2、al system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: Customer
3、Servicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-05REVISED2017-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.BFEDERAL SUPPLY CLASS 5935 AS81659/64 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS81659 SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advan
4、ce the state oftechnicaland engineering sciences.The use ofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe rev
5、ised,reaffirmed,stabilized,orcancelled.SAEinvitesyourwritten commentsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS81659/64B RATIONALE REVISION IS REQUIRED TO UPDATE THE CONNECTOR INSERT AND INSTALLING/REMOVAL TOOL REFERENC
6、ES. FIGURE 1 - CONNECTOR SUGGESTED PANEL CUTOUT/RECOMMENDED MATED POSITION TABLE 1 INCH MM INCH MM INCHES MM INCHES MM INCHES MM .006 .040 .047 .050 .055 .060 .062 .065 0.15 1.02 1.19 1.27 1.40 1.52 1.57 1.65 .093 .117 .118 .122 .133 .178 .198 .281 2.36 2.97 3.00 3.10 3.38 4.52 5.03 7.14 .297 .521 .
7、541 .928 .930 .948 1.326 1.367 1.387 7.54 13.23 13.74 23.57 23.62 24.08 33.68 34.72 35.23 1.3915 1.427 1.447 1.648 1.860 2.250 2.485 2.505 35.34 36.25 36.75 41.86 47.24 57.15 63.12 63.62 2.783 3.060 3.090 3.296 3.595 3.625 3.645 3.845 3.875 70.69 77.12 78.49 83.72 91.31 92.08 92.58 97.66 98.42 AEROS
8、PACE STANDARD AS81659/64 SHEET 2 OF 3 REV. B CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE,CRIMP CONTACTS, (QUADRUPLE INSERT, TYPE III, CLASS 1,(-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 - CONNECTOR CONFIGURATIONS AND DIMENSIONS AEROSPACE STANDARD AS81659/64 SHEET 3 OF 3 REV. B CONN
9、ECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE,CRIMP CONTACTS, (QUADRUPLE INSERT, TYPE III, CLASS 1,(-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 - CONNECTOR CONFIGURATIONS AND DIMENSIONS (CONTINUED) REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS816
10、59. 1. DESIGN: CONNECTOR ACCESSORIES SHALL BE DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. TOLERANCES: DECIMALS .010 UNLESS OTHERWISE SPECIFIED. METRIC EQUIVALENTS (TO THE NEAREST 0.01 MM) ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 I
11、NCH = 25.4 MM. NORMAL (01) POLARIZATION POSITION SHOWN, FOR ALTERNATE POSITIONS SEE AS81659. FOR LOCATION OF DATUMS G AND H REFER TO AS81659, FIGURE 11. THIS CONNECTOR DOES NOT HAVE A WIRE SEALING GROMMET. 2. INSERT ARRANGEMENTS SHALL BE IN ACCORDANCE WITH AS31571. 3. CONTACTS SHALL BE IN ACCORDANCE
12、 WITH AS39029/11 OR AS39029/12, AS APPLICABLE. 4. INSTALLING AND REMOVAL TOOLS SHALL BE IN ACCORDANCE WITH AS81969/1 OR AS81969/14. SPECIFICATION NOTES 1. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, N
13、OT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
