1、 AEROSPACE STANDARD TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBACK TYPE, SERIES II AS81714/60Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by a
2、ny means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae
3、org ISSUED 2004-04REAFFIRMED 2012-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5940 AS81714/60SHEET 1 OF 6 SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirel
4、y voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites y
5、ourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81714/60 RATIONALE AS81714/60 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S
6、 MILITARY SPECIFICATION MIL-T-81714/60A, NOTICE 1 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-T-81714/60A, NOTICE 1. ANY PART N
7、UMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND ST
8、ANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, A
9、NY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT. AEROSPACE STANDARD AS81714/60SHEET 2 OF 6 TERMINAL JUNCTION SYSTEM,
10、 TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBACK TYPE, SERIES II THIS SPECIFICATION IS APPROVED FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE. THE COMPLETE REQUIREMENTS FOR ACQUIRING THE MODULE DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE
11、 OF SPECIFICATION MIL-T-81714. FIGURE 1. BLOCK SIZE 22, 20 AND 16. MIL-T-81714/60A, DATED 27 JUNE 1990, IS INACTIVE FOR NEW DESIGN AND IS NO LONGER USED, EXCEPT FOR REPLACEMENT PURPOSES. AEROSPACE STANDARD AS81714/60SHEET 3 OF 6 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING
12、MODULES, FEEDBACK TYPE, SERIES II FIGURE 2. BLOCK, SIZE 12. AEROSPACE STANDARD AS81714/60SHEET 4 OF 6 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBACK TYPE, SERIES II FIGURE 3. BUSSING ARRANGEMENTS. AEROSPACE STANDARD AS81714/60SHEET 5 OF 6 TERMINAL JUNCTION S
13、YSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBACK TYPE, SERIES II TABLE 1. DIMENSIONS. DIMENSIONS COMPONENT DESIGNATOR BUSSING DESIGNATOR BUS/CONTACT DESCRIPTION A MAX B MAX 22 01 1 20 PIN BUS .760 .730 22 02 2 10 PIN BUSES .760 .730 22 04 4 5 PIN BUSES .760 .730 22 05 5 4 PIN BU
14、SES .760 .730 22 06 2 2 PIN BUSES 4 4 PIN BUSES .760 .730 22 10 10 2 PIN BUSES .760 .730 20 01 1 12 PIN BUS .920 .890 20 02 2 6 PIN BUSES .920 .890 20 03 3 4 PIN BUSES .920 .890 20 04 4 3 PIN BUSES .920 .890 20 06 6 2 PIN BUSES .920 .890 16 01 1 6 PIN BUS .920 .890 16 02 2 3 PIN BUSES .920 .890 16 0
15、3 3 2 PIN BUSES .920 .890 12 01 1 6 PIN BUS 1.047 1.017 12 02 2 3 PIN BUSES 1.047 1.017 12 03 3 2 PIN BUSES 1.047 1.017 TABLE 2 COMPONENT DESIGNATOR CONTACT PART NOS. INSERTING/REMOVAL TOOL END SEALING PLUG BLOCK REMOVAL TOOL 22 M39029/22-191 M81969/14-01 MS27488-22 M81714/69-01 20 M39029/22-192 M81
16、969/14-10 M27488-20 M81714/69-01 16 M39029/22-193 M81969/14-03 M27488-16 M81714/69-01 12 M39029/22-605 M81969/16-03 M81969/8 -10 M27488-12 M81714/69-02 INCH MM INCH MM INCH MM INCH MM .005 .006 .007 .010 .012 .016 .018 .030 .035 0.13 0.15 0.18 0.25 0.30 0.41 0.46 0.76 0.89 .040 .051 .065 .083 .093 .
17、102 .110 .130 .180 1.02 1.30 1.65 2.11 2.36 2.59 2.79 3.30 4.57 .186 .225 .226 .250 .280 .315 .510 .518 .672 4.72 5.72 5.74 6.35 7.11 8.00 12.95 13.16 17.07 .730 .760 .890 .920 1.017 1.020 1.047 18.54 19.30 22.61 23.37 25.83 25.91 26.59 AEROSPACE STANDARD AS81714/60SHEET 6 OF 6 TERMINAL JUNCTION SYS
18、TEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBACK TYPE, SERIES II NOTES: 1. DIMENSIONS ARE IN INCHES. 2. METRIC EQUIVALENTS (TO THE NEAREST .01MM) ARE GIVEN TOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH - 25.4MM. 3. BLOCK IS DESIGNED FOR INSTALLATION IN MIL-T-81714/67 RACKS OR MIL-T-81714/68 BRACKETS. 4. THE PART NUMBER CONSISTS OF THE LETTER M, SPECIFICATION SHEET NUMBER, COMPONENT DESIGNATOR AND BUSSING DESIGNATOR (SEE FIGURE 3).
