1、AEROSPACE STANDARDTUBING, PLASTIC, LIGHTWEIGHT, ZERO HALOGEN, EXTRA FLEXIBLE, CONVOLUTED, HELICAL, CLOSECONVOLUTION, POLYETHERETHERKEYTONE (PEEK)AS81914/11Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted,
2、in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRE
3、SS: http:/www.sae.orgISSUED2011-01REVISED2016-05THIRD ANGLE PROJECTIONCUSTODIAN: AE-8/AE-8C1REV.BFEDERAL SUPPLY CLASS9330AS81914/11SHEET 1 OF 4REV.BPROCUREMENT SPECIFICATION: AS81914SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sc
4、iences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,o
5、rcancelled.SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81914/11BRATIONALEREVISION IS REQUIRED TO MODIFY THE REQUIREMENTS AND PART NUMBER TO ALLOW FOR THE OPTION OF AN ADDITIONA
6、L MATERIAL COLOR.NOTICETHE REQUIREMENTS FOR ACQUIRING THE TUBING DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE IN EFFECT OF AS81914.FIGURE 1 DIMENSIONS AND CONFIGURATIONAEROSPACE STANDARDAS81914/11SHEET 2 OF 4REV.BTUBING, PLASTIC, LIGHTWEIGHT, ZERO HALOGEN, EXTRA FLEXIBLE, CON
7、VOLUTED, HELICAL, CLOSECONVOLUTION, POLYETHERETHERKEYTONE (PEEK)TABLE 1 FIGURE 1 DIMENSIONSDASH NUMBERMAXINSIDEDIA. (I.D.)MININSIDEDIA. (I.D.)MAXOUTERDIA. (O.D.)MAXWALLTHICK-NESSCONVO-LUTIONS PER INCH(CPI) 1APPROX. WEIGHT LBS (KG) PER 100 FEET (30.5 M) REF.MINBENDRADIUS01.188 (4.78).181 (4.60).307 (
8、7.80) .010 (0.25) 8 0.6 (0.27).31 (7.9)02.281 (7.14).273 (6.93).405 (10.29) .010 (0.25) 8 0.8 (0.36).44 (11.2)03.312 (7.92).300 (7.62).440 (11.18) .010 (0.25) 8 1.4 (0.64).44 (11.2)04.375 (9.53) .364 (9.25).500 (12.70) .010 (0.25) 8 1.6 (0.73).50 (12.7)05.437 (11.10).427 (10.85).550 (13.97) .010 (0.
9、25) 8 1.8 (0.82).63 (16.0)06.500 (12.70).485 (12.32).630 (16.00) .010 (0.25) 8 2.0 (0.91).75 (19.1)07.625 (15.88).608 (15.44).750 (19.05) .010 (0.25) 8 2.4 (1.09).75 (19.1)08.750 (19.05).730 (18.54).890 (22.61) .011 (0.28) 8 3.0 (1.36).94 (23.9)09.875 (22.23).855 (21.72)1.060 (26.92) .011 (0.28) 8 3
10、8 (1.72)1.13 (28.7)101.000 (25.40).980 (24.89)1.195 (30.35) .012 (0.30) 7 5.2 (2.36)1.25 (31.8)111.125 (28.58)1.105 (28.07)1.350 (34.29) .012 (0.30) 7 6.4 (2.90)1.31 (33.3)121.250 (31.75)1.220 (30.99)1.500 (38.10) .012 (0.30) 7 9.8 (4.45)1.44 (36.6)131.500 (38.10)1.480 (37.59)1.780 (45.21) .014 (0.
11、36) 7 11.5 (5.22)1.75 (44.5)141.750 (44.45)1.730 (43.94)2.020 (51.31) .014 (0.36) 7 14.0 (6.35)2.00 (50.8)152.000 (50.80)1.980 (50.29)2.280 (57.91) .015 (0.38) 7 16.0 (7.26)2.25 (57.2)NOTES:1. DIMENSIONS ARE IN INCHES.2. UNLESS OTHERWISE SPECIFIED TOLERANCES SHALL BE: .XX = .010 (0.25 MM), .XXX = .0
12、05 (0.13 MM).3. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 25.4 MM = 1 INCH.4. METRIC DIMENSIONS IN PARENTHESES ARE SHWON IN MILLIMETERS.REQUIREMENTS:1. DIMENSIONS AND CONFIGURATION: SEE FIGURE 1 AND TABLE 1.2. CONVOLUTION TYPE: HELICAL, CLOSE CONVOLUTION (CLASS 0).3.
13、 LENGTHS SHALL BE SPECIFIED IN FEET BY THE PROCURING ACTIVITY AND DOES NOT FORM A PART OF THE IDENTIFYING PART NUMBER. MINIMUM ORDER LENGTH SHALL BE 3 FEET (0.914 M) AND THE TUBING ORDER LENGTH TOLERANCES SHALL BE AS SPECIFIED IN TABLE 2. TUBING SHALL BE PROCURED AS COILS.AEROSPACE STANDARDAS81914/1
14、1SHEET 3 OF 4REV.BTUBING, PLASTIC, LIGHTWEIGHT, ZERO HALOGEN, EXTRA FLEXIBLE, CONVOLUTED, HELICAL, CLOSECONVOLUTION, POLYETHERETHERKEYTONE (PEEK)TABLE 2 ORDER LENGTH TOLERANCEORDER LENGTH RANGELENGTH IN FEET (METERS) TOLERANCE IN INCHES (MM)3 - 12 (0.914 M 3.66 M) + 2.0 / - 0.0 (+ 50.8 MM / - 0.0 MM
15、)13 - 50 (3.96 M 15.24 M) + 4.0 / - 0.0 (+ 101.6 MM / - 0.0 MM)51 AND UP (15.55 M AND UP) + 6.0 / - 0.0 (+ 152.4 MM / - 0.0 MM)4. CONTINUOUS OPERATING TEMPERATURE: -55 C ( -67 F) TO 250 C (482 F).5. COLOR: COLOR SHALL BE BLACK OR CLEAR/NATURAL (SEE PART NUMBER EXAMPLE FOR APPROPRIATE DESIGNATOR).6.
16、PHYSICAL PROPERTIES: GENERAL PHYSICAL REQUIREMENT VALUES ALONG WITH ASSOCIATED TEST CONDITIONS ARE LOCATED IN TABLE 3.7. SHELF LIFE: THE STORAGE/SHELF LIFE SHALL BE 20 YEARS. TABLE 3 PHYSICAL PROPERTIESPROPERTY REQUIREMENTCONSTRUCTION DETAILS IN ACCORDANCE WITH TABLE 1STRESS IN PSI 10% STRAIN 250 TO
17、 900SPECIFIC GRAVITY 1.32 MAXCRUSH RESISTANCE, HORIZONTAL 10 LBS (4.54KG) MINHEAT SHOCK234/230C (454/446F) FOR 4 HOURS. 15% MAX LONGITUDINAL CHANGE. NO DRIPPING, FLOWING OR CRACKING HEAT AGINGSTRESS IN PSI 10% STRAIN, 80% OF INITIAL VALUE. 179/175 C (354/347 F) FOR 96 HOURSFLUID RESISTANCE STRESS IN
18、 PSI 10% STRAIN 80% OF INITIAL VALUEFLAMMABILITY NON-FLAMMABLE 1/FUNGUS RESISTANCE NON-NUTRIENT 1/HALOGEN ZERO HALOGEN 1/DIELECTRIC BREAKDOWN 12000 VOLTS, NO BREAKDOWN1/ PROPERTIES NOT TESTED FOR.PART NUMBER OR IDENTIFYING NUMBER (PIN).EXAMPLE : M81914 /11 1 0 06 D H CC = CLEAR/NATURAL, OMIT FOR BLA
19、CKHELIX WIRE, OMIT FOR NONE DRAIN HOLES, OMIT FOR NONE DASH NUMBER, (SEE TABLE 1)CLASS (SEE REQUIREMENTS)CONVOLUTION TYPE: 1 = HELICAL DETAIL SHEETBASIC PART NUMBERQUALIFICATION: SEE AS81914AEROSPACE STANDARDAS81914/11SHEET 4 OF 4REV.BTUBING, PLASTIC, LIGHTWEIGHT, ZERO HALOGEN, EXTRA FLEXIBLE, CONVO
20、LUTED, HELICAL, CLOSECONVOLUTION, POLYETHERETHERKEYTONE (PEEK)SPECIFICATION NOTES:1. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THISDOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
