1、 AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE I AND II, CLASS 2, COMPOSITION B AS81969/10Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any mea
2、ns, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org I
3、SSUED 2015-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/10 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport
4、is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE in
5、vites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/10 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/10 WITH THIS DOC
6、UMENT, TO IMPROVE DRAWING LEGIBILITY, TO UPDATE QUALIFICATION INFORMATION, TO REMOVE GOVERNMENT JARGON AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. INSTALLING TOOL (-01) REMOVAL T
7、OOL (-02) FIGURE 1 - INSTALLING AND REMOVAL TOOL CONFIGURATIONS/DIMENSIONS AEROSPACE STANDARD AS81969/10 SHEET 2 OF 2 INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE I AND II, CLASS 2, COMPOSITION B TABLE 1 - METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETE
8、RS INCHES MILLIMETERS.007 0.18 .040 1.02 .14 3.56 .50 12.70 .010 0.025 .060 1.52 .25 6.35 2.00 50.80.02 0.51 .075 1.91 .28 7.11 .025 0.64 .087 2.21 .31 7.87 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TOOL SHALL BE DESIGNED IN ACCORDA
9、NCE WITH FIGURE 1. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .015 INCH (0.38 MILLIMETERS). 2. MATERIAL AND FINISHES: MATERIAL-ACETAL RESIN (FORMULATION OPTIONAL)
10、3. PART NUMBER/MARKING: INSTALLING TOOL- M81969/10-01 REMOVAL TOOL-M81969/10-02 EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED WITH THE MANUFACTURERS IDENTIFICATION AND PART NUMBER IN ACCORDANCE WITH MIL-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. TOOL COLOR: INSTA
11、LLING TOOL-GREEN, REMOVAL TOOL-WHITE 4. CONTACT INSTALLATION AND REMOVAL: TO INSTALL CONTACT, PLACE INSTALLING TOOL AROUND WIRE AND AGAINST SHOULDER BEFORE INSTALLING CONTACT. A “CLICKING” SOUND, FOLLOWED BY INCREASED RESISTANCE TO FURTHER FORWARD MOTION INDICATES A FULLY INSTALLED CONTACT. CHECK TH
12、E CONTACT RETENTION BY EXERTING A LIGHT PULL (APPROXIMATELY 1 POUND) ON THE WIRE. TO REMOVE CONTACT, INSERT REMOVAL TOOL STRAIGHT INTO THE CONTACT CAVITY UNTIL BOTTOMED TO RELEASE CONTACT. USE A ROD .040 TO .041 INCH (1.02 TO 1.04 MILLIMETERS), EITHER ROUND ENDED OR FLAT ENDED WITH NO SHARP EDGES TO
13、 PUSH CONTACT AND TOOL OUT THE REAR OF THE RECEPTACLE INSERT. 5. QUALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS81969 WITH THE FOLLOWING EXCEPTIONS: PLUNGER FORCE - NOT APPLICABLE ALTERNATIVE QUALIFICATION REQUIREMENTS SUCH AS CERTIFICATION, FIRST ARTICLE OR QC TESTING MAY BE IMPOSED BY
14、THE QUALIFYING ACTIVITY (QA). THE QA SHALL SUBMIT A WRITTEN REQUEST TO THE AE-8C2 COMMITTEE FOR REVIEW AND APPROVAL OF THE ALTERNATIVE QUALIFICATION TESTING PROGRAM PRIOR TO IMPLEMENTATION OF THE REQUIREMENT. APPLICATION NOTES: 1. THESE TOOLS SHALL BE USED TO INSTALL AND REMOVE CONTACTS SPECIFIED IN
15、 MIL-DTL-55302/82. 2. THIS DOCUMENT SUPERSEDES MIL-I-81969/10A DATED 11 JANUARY 1979 AND MIL-C-55302/86 DATED 25 OCT 1973. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
