1、AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE III, CLASS 2, COMPOSITION BAS81969/39Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elec
2、tronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 20
3、14-03THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS81969/39SHEET 1 OF 2PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entire
4、ly voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites
5、yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/39RATIONALE AS81969/39 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/39 WITH THIS DOCUMENT. IT INCLUDES ENGINEERING POSITION L
6、ETTERS, MILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED REFLECTING THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF
7、 AS81969. INSERTION TIP DETAILS REMOVAL TIP DETAIL FIGURE 1 - M81969/39-01 INSTALLING AND REMOVAL TOOL AEROSPACE STANDARD AS81969/39SHEET 2 OF 2INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE III, CLASS 2, COMPOSITION B REQUIREMENTS: ALL COMPLETE REQUIREMENTS SHALL CONSIST OF THIS D
8、OCUMENT AND THE LATEST ISSUE OF AS81969. 1. CONFIGURATION: CONFIGURATION SHALL BE IN ACCORDANCE WITH FIGURE 1. UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. PLASTIC TIPS SHALL SEPARATE AT THE TOOL CENTER SECTION. PLASTIC TIPS SHALL BE SMOOTH AND FREE OF BURRS AND SHARP EDGES. 2. MARKING: EAC
9、H TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON TOOL BODY WITH MANUFACTURER IDENTIFICATION AND THE SAE PART NUMBER IN ACCORDANCE WITH MIL-STD-130 (LOCATION OPTIONAL). MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. INSTALLING TIP SHALL BE GREEN AND REMOVAL TIP SHALL BE WHITE. 3.
10、 MATERIALS (SEE AS81969): TOOL MATERIAL SHALL BE ACETAL RESIN (FORMULATION OPTIONAL). 4. QUALIFICATION AND QUALITY CONFORMANCE: SLIT SHALL BE MEASURED WITH A MAXIMUM DIAMETER (.069 INCH) GAGE PIN INSERTED IN THE END OF EACH TIP. 5. PART NUMBER M81969 /39 -01 I I I I I I_ DASH NUMBER I I_ DETAIL SPEC
11、IFICATION NUMBER I_ BASIC SPECIFICATION NUMBER APPLICATION NOTES: 1. TOOL IS USED TO INSTALL AND REMOVE SIZE 20 CONTACTS FROM MIL-DTL-24308 AND AS81659 CONNECTORS. 2. AS81969/39 SUPERSEDES MIL-I-81969/39B. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF
12、THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
