1、 AEROSPACE STANDARD CABLE, ELECTRIC, FILTER LINE, COMPONENT WIRE, SILVER-COATED HIGH-STRENGTH COPPER ALLOY CONDUCTOR, RADIO FREQUENCY ABSORPTIVE, 150C, 600-VOLT AS85485/10 Copyright 2004 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval syste
2、m or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE
3、WEB ADDRESS: http:/www.sae.org ISSUED 2004-06THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8D FEDERAL SUPPLY CLASS6145 AS85485/10SHEET 1 OF 4 PROCUREMENT SPECIFICATION: MIL-C-85485SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andeng
4、ineering sciences. Theuse of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffir
5、med, revised, orcancelled.SAE invites yourwritten commentsandsuggestions. NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-C-85485/10A AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE T
6、ECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-C-85485/10A. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (
7、TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE E
8、XISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AN
9、D IS NOT PART OF THIS TECHNICAL REPORT. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD CABLE, ELECTRIC, FILTER LINE, COMPONENT WIRE, SILVER- COATED HIGH-STRENGTH COPPER ALLOY COND
10、UCTOR, RADIO FREQUENCY ABSORPTIVE, 150C, 600-VOLT AS85485/10 AS85485/10SHEET 2 OF 4 FIGURE 1. GENERAL CONFIGURATION TABLE I. CONSTRUCTION DETAILS TABLE II. PERFORMANCE DETAILS Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted with
11、out license from IHS-,-,-AEROSPACE STANDARD CABLE, ELECTRIC, FILTER LINE, COMPONENT WIRE, SILVER- COATED HIGH-STRENGTH COPPER ALLOY CONDUCTOR, RADIO FREQUENCY ABSORPTIVE, 150C, 600-VOLT AS85485/10 AS85485/10SHEET 3 OF 4 RATINGS: TEMPERATURE RATING: 150C (302F) MAXIMUM CONTINUOUS CONDUCTOR TEMPERATUR
12、E. VOLTAGE RATING: 600 VOLTS (RMS) AT SEA LEVEL. ADDITIONAL REQUIREMENTS: ATTENUATION (INSERTION LOSS): THE WIRE OF THIS SPECIFICATION SHEET, WHEN SHIELDED IN ACCORDANCE WITH M85485/12-*1*, SHALL MEET THE ATTENUATION REQUIREMENTS OF TABLE III AS SPECIFIED FOR THE APPLICABLE SIZE OF WIRE. BLOCKING: 2
13、00 3C (392 5F) FOR 6 HOURS COLOR: PRIMARY INSULATION - NATURAL FILTER LAYER - BLACK PRIMARY JACKET - LIGHT VIOLET COLOR STRIPING DURABILITY: 125 CYCLES (250 STROKES) (MIN), 500 GRAMS WEIGHT. CONCENTRICITY: PRIMARY INSULATION - 50% (MIN); FINISHED WIRE - 70% (MIN). CROSSLINKING PROOF TEST: 7 HOURS AT
14、 300 3C (572 5F). FLAMMABILITY: 3 SECONDS (MAX); 3 INCHES (MAX). HUMIDITY RESISTANCE: INSULATION RESISTANCE, 5000 MEGOHMS FOR 1000 FEET (MIN). IDENTIFICATION DURABILITY: 125 CYCLES (250 STROKES) (MIN), 500 GRAMS WEIGHT. IMMERSION: DIAMETER INCREASE 5% (MAX); NO CRACKING, NO DIELECTRIC BREAKDOWN. INS
15、ULATION ELONGATION AND TENSILE STRENGTH: PRIMARY INSULATION, FILTER LAYER AND PRIMARY JACKET PULLED TOGETHER. ELONGATION, 50% (MIN) TENSILE STRENGTH, 3000 LBF/IN2(MIN) INSULATION FLAWS: PRIMARY INSULATION ONLY SPARK TEST; 1.5 KILOVOLTS (RMS), 60 HZ IMPULSE DIELECTRIC TEST; 6.0 KILOVOLTS (PEAK) FINIS
16、HED WIRE SPARK TEST; 3.0 KILOVOLTS (RMS), 60 HZ IMPULSE DIELECTRIC TEST; 8.0 KILOVOLTS (PEAK) INSULATION RESISTANCE: 5000 MEGOHMS FOR 1000 FEET (MIN) INSULATION THICKNESS: PRIMARY INSULATION; 0.002 INCH (MIN) FILTER LAYER; AVERAGE 0.0025 INCH (MIN) PRIMARY JACKET; 0.0035 INCH (MIN) LIFE CYCLE: 168 H
17、OURS AT 200 3C (392 5F) LOW TEMPERATURE-COLD BEND: -65 2C (-85 4F) FOR 4 HOURS SHRINKAGE: 0.125 INCH (MAX) AT 200 3C (392 5F) SMOKE: 200 2C (392 4F); NO VISIBLE SMOKE. SURFACE RESISTANCE: 500 MEGOHM-INCHES (MIN), INITIAL AND FINAL READINGS. THERMAL SHOCK RESISTANCE: OVEN TEMPERATURE, 150 3C (302 5F)
18、 MAXIMUM CHANGE IN MEASUREMENT, 0.060 INCH THERMAL STABILITY: 1250 HOURS AT 180 3C (356 5F). THE WIRE OF THIS SPECIFICATION SHEET, WHEN SHIELDED IN ACCORDANCE WITH M85485/12-*1*, SHALL MEET THE VOLTAGE WITHSTAND (DIELECTRIC) OF 1500 VOLTS (RMS), 60 HZ, AND THE STOP BAND ATTENUATION REQUIREMENTS FOR
19、THE APPLICABLE SIZE OF WIRE AS SPECIFIED IN TABLE III. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD CABLE, ELECTRIC, FILTER LINE, COMPONENT WIRE, SILVER- COATED HIGH-STRENGTH CO
20、PPER ALLOY CONDUCTOR, RADIO FREQUENCY ABSORPTIVE, 150C, 600-VOLT AS85485/10 AS85485/10SHEET 4 OF 4 VOLTAGE WITHSTAND (POST-ENVIRONMENTAL): 1500 VOLTS (RMS), 60 HZ WRAP TEST: 6 HOURS AT 200 3C (392 5F); NO CRACKING. TABLE III. ATTENUATION (INSERTION LOSS) FIGURE 2. ATTENUATION (INSERTION LOSS) ENGINE
21、ERING REFERENCE CURVE APPLICATION NOTE: COMPONENT WIRE IS AN EFFECTIVE RADIO FREQUENCY ABSORPTIVE WIRE ONLY WHEN USED AS A COMPONENT IN A SHIELDED CABLE. QUALIFYING ACTIVITY: THE ACTIVITY RESPONSIBLE FOR THIS QUALIFIED PRODUCTS LIST IS THE NAVAL AIR SYSTEMS COMMAND, WASHINGTON, D.C. 20361. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
