1、 AEROSPACE STANDARD SLEEVING, FOR IDENTIFICATION MARKING HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE AS85848/1Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanica
2、l, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2002-02REAFFIRMED 2
3、012-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8D FEDERAL SUPPLY CLASS 5940 AS85848/1SHEET 1 OF 5 SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and
4、suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE
5、 values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85848/1 RATIONALE AS85848/1 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-S-858
6、48/1, AMENDMENT 1 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-S-85848/1, AMENDMENT 1. ANY PART NUMBERS ESTABLISHED BY THE ORIGIN
7、AL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A
8、) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND
9、ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction
10、or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85848/1SHEET 2 OF 5 SLEEVING, FOR IDENTIFICATION MARKING HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE THIS SPECIFICATION IS APPROVED FOR USE WITHIN THE NAVAL AIR SYSTEMS COMMAND, DEPARTMENT OF THE NAVY, AND IS AVAILABLE FOR USE BY AL
11、L DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE.THE COMPLETE REQUIREMENTS FOR PROCURING THE SLEEVING DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE ISSUE IN EFFECT OF MIL-S-85848(AS).REQUIREMENTS:CONTINUOUS OPERATING TEMPERATURE RANGE: TYPE I: -40C TO +105C (-40F TO +221F)TYPE II: -
12、40C TO +105C (-40F TO +221F)CLASSIFICATION: THE HEAT SHRINKABLE IDENTIFICATION SLEEVING SHALL BE FURNISHED IN THE FOLLOWING TYPES, AND CLASSES, AS SPECIFIED:TYPES.TYPE I - FLATWEB FORMATTYPE II - SLEEVING FORMATCLASSES.CLASS 1 - FLAME RESISTANTCLASS 2 - FLAMMABLECOLOR: THE STANDARD COLOR SHALL BE WH
13、ITE. OTHER COLORS ARE AVAILABLE. ALL COLORS SHALL CONFORM TO THE REQUIREMENTS OF CLASS 1 OF MIL-STD-104.MILITARY PART NUMBER: THE MILITARY PART NUMBER SHALL CONSIST OF THE BASIC NUMBER OF THIS SPECIFICATION SHEET AND DASH NUMBERS AS SHOWN BELOW:PART NUMBER EXAMPLE: WHITE, TYPE I, CLASS 1, .500 WIDTH
14、 1,000 LENGTH IDENTIFICATION SLEEVING SHALL BE IDENTIFIED AS M85848/1-1104-9.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85848/1SHEET 3 OF 5 SLEEVING, FOR IDENTIFICATION MAR
15、KING HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE TABLE I - CONSTRUCTION DETAILS FOR TYPE I (FLATWEB) (INCHES)Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85848/1SHEET 4 OF 5 SLEEVIN
16、G, FOR IDENTIFICATION MARKING HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE TABLE II CONSTRUCTION DETAILS FOR TYPE II SLEEVINGTABLE III - PHYSICAL PROPERTIES 1/Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,
17、AEROSPACE STANDARD AS85848/1SHEET 5 OF 5 SLEEVING, FOR IDENTIFICATION MARKING HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE TABLE III - PHYSICAL PROPERTIES (CONTINUED) 1/RESTRICTED SHRINKAGE: TEST METHOD 4.6.3, 149 2C (300 4F) FOR 3 TO 5 MINUTES UNTIL THE SLEEVE IS SNUG.UNRESTRICTED SHRINKAGE: 4.5.1, 149 2
18、C (300 4F) FOR 5 MINUTES.SHELF LIFE CONDITIONS: SUPPLIER SHALL CERTIFY TO STORAGE AT AMBIENT STORAGE CONDITIONS FOR TWO YEARS FOLLOWED BY CONFORMANCE TO THE CONSTRUCTION DETAILS OF EITHER TABLE I OR TABLE II.SHELF LIFE EXTENSION: 4.6.13INTENDED USE. HEAT SHRINKABLE POLYOLEFIN IDENTIFICATION SLEEVING
19、 IS USED AS A SNUG FITTING NON-INSULATING MATERIAL TO IDENTIFY WIRES, WIRE BUNDLES, CABLES AND CABLE HARNESSES.NOTICE1. FLAMMABILITY - CLASS 2 HEAT SHRINKABLE IDENTIFICATION SLEEVING DESCRIBED IN THIS SPECIFICATION SHEET HAS NOT BEEN FLAME RETARDED AND WILL BURN READILY. CLASS 2 SLEEVING SHALL NOT BE CONSIDERED FOR PROCUREMENT WHEN FLAME RESISTANCE IS REQUIRED.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
