1、 AEROSPACE STANDARD SLEEVING, FOR IDENTIFICATION MARKING HEAT SHRINKABLE, POLYVINYLIDENE FLUORIDE, FLEXIBLE AS85848/2Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electron
2、ic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2002-0
3、2REAFFIRMED 2012-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8D FEDERAL SUPPLY CLASS 5940 AS85848/2SHEET 1 OF 5 SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applic
4、ability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsugges
5、tions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85848/2 RATIONALE AS85848/2 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION
6、 MIL-S-85848/2, AMENDMENT 1 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-S-85848/2, AMENDMENT 1. ANY PART NUMBERS ESTABLISHED BY
7、THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROV
8、IDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIRE
9、MENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo rep
10、roduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85848/2SHEET 2 OF 5 SLEEVING, FOR IDENTIFICATION MARKING HEAT SHRINKABLE, POLYVINYLIDENE FLUORIDE, FLEXIBLE THIS SPECIFICATION IS APPROVED FOR USE WITHIN THE NAVAL AIR SYSTEMS COMMAND, DEPARTMENT OF THE NAVY, AND IS
11、AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE.THE COMPLETE REQUIREMENTS FOR PROCURING THE SLEEVING DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE ISSUE IN EFFECT OF MIL-I-85848(AS).REQUIREMENTS:CONTINUOUS OPERATING TEMPERATURE RANGE: TYPE I: -40C TO +150C (-
12、40F TO +302F)TYPE II: -40C TO +150C (-40F TO +302F)CLASSIFICATION: THE HEAT SHRINKABLE IDENTIFICATION SLEEVING SHALL BE FURNISHED IN THE FOLLOWING TYPES, AS SPECIFIED:TYPE I - FLATWEB FORMATTYPE II - SLEEVING FORMATCOLOR: THE STANDARD COLOR SHALL BE WHITE. OTHER COLORS ARE AVAILABLE. ALL COLORS SHAL
13、L CONFORM TO THE REQUIREMENTS OF CLASS 1 OF MIL-STD-104.MILITARY PART NUMBER: THE MILITARY PART NUMBER SHALL CONSIST OF THE BASIC NUMBER OF THIS SPECIFICATION SHEET AND DASH NUMBERS AS SHOWN BELOW:PART NUMBER EXAMPLE: WHITE, TYPE II, .187 AS SUPPLIED DIAMETER, 1.62 INCH LENGTH SHALL BE IDENTIFIED AS
14、 : M85848/2-2004-9.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85848/2SHEET 3 OF 5 SLEEVING, FOR IDENTIFICATION MARKING HEAT SHRINKABLE, POLYVINYLIDENE FLUORIDE, FLEXIBLE TAB
15、LE I - CONSTRUCTION DETAILS FOR TYPE I FLATWEB (INCHES)TABLE II CONSTRUCTION DETAILS FOR TYPE II SLEEVING (INCH)Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85848/2SHEET 4 OF
16、5 SLEEVING, FOR IDENTIFICATION MARKING HEAT SHRINKABLE, POLYVINYLIDENE FLUORIDE, FLEXIBLE TABLE III - PHYSICAL PROPERTIES 1/RESTRICTED SHRINKAGE: TEST METHOD 4.6.3 AT 204 2C (400 4F) UNTIL SLEEVING IS SNUG AROUND THE WIRE.UNRESTRICTED SHRINKAGE: TEST METHOD 4.5.2. 200 2C (392 4F) FOR 5 MINUTES.Copyr
17、ight SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85848/2SHEET 5 OF 5 SLEEVING, FOR IDENTIFICATION MARKING HEAT SHRINKABLE, POLYVINYLIDENE FLUORIDE, FLEXIBLE SHELF LIFE CONDITIONS: SUPP
18、LIER SHALL CERTIFY TO STORAGE AT AMBIENT STORAGE CONDITIONS FOR TWO YEARS FOLLOWED BY CONFORMANCE TO THE CONSTRUCTION DETAILS OF EITHER TABLE I OR TABLE II.SHELF LIFE EXTENSION: 4.6.13INTENDED USE. HEAT SHRINKABLE FLEXIBLE POLYVINYLIDENE FLUORIDE IDENTIFICATION SLEEVING IS USED AS A SNUG FITTING NON-INSULATING IDENTIFIER TO MARK WIRES, WIRE BUNDLES, CABLES AND CABLE HARNESSES.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
