1、AEROSPACE STANDARDBOLT, MACHINE - HEXAGON HEAD, DRILLED, 1 HOLE,PD SHANK, STEEL, UNS K14675, DIFFUSED NICKEL-CADMIUM PLATE, 195 KSI MIN, .1900-32 UNJF-3AAS9685Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitt
2、ed, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB A
3、DDRESS: http:/www.sae.orgISSUED2000-08 REAFFIRMED2007-06 REVISED2016-06THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.BFEDERAL SUPPLY CLASS5306AS9685SHEET 1 OF 2REV.BPROCUREMENT SPECIFICATION: AS7459SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandeng
4、ineering sciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,isthe soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,st
5、abilized,orcancelled. SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9685BRATIONALEREVISE THREAD SPECIFICATION TO AS8879, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING, UPDATE MAGN
6、ETIC PARTICLE INSPECTION REFERENCE, ADD DATUM W, DATUM U, AND POSITIONAL REQUIREMENTS FOR DRILLED HOLE, CHANGE DRILLED HOLE LOCATION (FROM BEARING FACE) TO A BASIC DIMENSION, ADD NEW EXISTING INVENTORY USE NOTE, UPDATE ANSI Y14.5M-1983 SYMBOLS, UPDATE CADMIUM NOTICE, AND GENERAL EDITORIAL REVISION.N
7、OTICETHE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9685, NOTICE 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT.ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATOR
8、Y FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT.FIGURE 1 - BOLTAEROSPACE STANDARDAS9685SHEET 2 OF 2REV.BBOLT, MACHINE - HEXAGON HEAD, DRILLED, 1 HOLE,PD SHANK, STEEL, UNS K14675, DIFFUSED NICKEL-CADMIUM PLATE
9、 195 KSI MIN, .1900-32 UNJF-3ATABLE 1 - PART NUMBERS AND DIMENSIONSPART NO. L KAPPROX.MASSLB/100 PART NO. L KAPPROX.MASSLB/100MS9685-03MS9685-04MS9685-05.302 - .322.365 - .385.428 - .448.072 - .092.072 - .092.072 - .092.70.74.78MS9685-25MS9685-26MS9685-271.678 -1.6981.740 - 1.7601.802 - 1.822.998 -
10、 1.0581.060 - 1.1201.122 - 1.1821.581.621.66MS9685-06MS9685-07MS9685-08.490 - .510.552 - .572.615 - .635.072 - .092.072 - .092.072 - .092.82.86.90MS9685-28MS9685-29MS9685-301.865 - 1.8851.928 - 1.9481.990 - 2.0101.185 - 1.2451.248 - 1.3081.310 - 1.3701.701.741.78MS9685-09MS9685-10MS9685-11.678 - .69
11、8.740 - .760.802 - .822.072 - .092.072 - .120.122 - .182.94.981.02MS9685-31MS9685-32MS9685-332.115 - 2.1352.240 - 2.2602.365 - 2.3851.435 - 1.4951.560 - 1.6201.685 - 1.7451.861.942.02MS9685-12MS9685-13MS9685-14.865 - .885.928 - .948.990 - 1.010.185 - .245.248 - .308.310 - .3701.061.101.15MS9685-34MS
12、9685-35MS9685-362.490 - 2.5102.615 - 2.6352.740 - 2.7601.810 - 1.8701.935 - 1.9952.060 - 2.1202.102.182.26MS9685-15MS9685-16MS9685-171.052 - 1.0721.115 - 1.1351.178 - 1.198.372 - .432.435 - .495.498 - .5581.191.231.27MS9685-37MS9685-38MS9685-392.865 - 2.8852.990 - 3.0103.115 - 3.1352.185 - 2.2452.31
13、0 - 2.3702.435 - 2.4952.342.422.50MS9685-18MS9685-19MS9685-201.240 - 1.2601.302 - 1.3221.365 - 1.385.560 - .620.622 - .682.685 - .7451.311.351.38MS9685-40MS9685-41MS9685-423.240 - 3.2603.365 - 3.3853.490 - 3.5102.560 - 2.6202.685 - 2.7452.810 - 2.8702.582.662.74MS9685-21MS9685-22MS9685-231.428 - 1.4
14、481.490 - 1.5101.552 - 1.572.748 - .808.810 - .870.872 - .9321.421.461.50MS9685-43MS9685-44MS9685-453.615 - 3.6353.740 - 3.7603.865 - 3.8852.935 - 2.9953.060 - 3.1203.185 - 3.2452.822.902.98MS9685-24 1.615 - 1.635 .935 - .995 1.54NOTES:NOTICETHIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS
15、A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE./1/ FOR PART NUMBERS MS9685-03 THROUGH MS9685-14 DATUM Z SHALL REPLACE DATUM Y.2. MATERIAL: LOW ALLOY STEEL AMS6304 (UNS K14675).3. PROCUREMENT SPECIFICATION: AS7459.4. FINISH: DIFFUSED NICKEL-CADMIUM PLATE AMS
16、2416. DIMENSIONS APPLY AFTER PLATING. CONTACT POINTS PERMISSIBLE. PD MAY BE REDUCED .0012 MAXIMUM BEFORE PLATING.5. MAGNETIC PARTICLE INSPECTION PER ASTM E1444/E1444M BEFORE PLATING.6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED,SURFACES TO BE 1
17、25 MICROINCHES Ra.7. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED.8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION).9. DIMENSIONS IN INCHES.10. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION
18、 MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED.11. DO NOT USE UNASSIGNED PART NUMBERS.12. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF
19、THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
