1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefro
2、m, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243TO PLACE A DOCUMENT
3、 ORDER; (724) 776-4970 FAX: (724) 776-0790SAE WEB ADDRESS http:/www.sae.orgCopyright 1976 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.S.A.SURFACEVEHICLE400 Commonwealth Drive, Warrendale, PA 15096-0001INFORMATIONREPORTSubmitted for recognition as an American National Stand
4、ardJ470cREV.JUL76Issued 1946-01Revised 1976-07Superseding J470bWROUGHT NICKEL AND NICKEL-RELATED ALLOYSForewordThis Reaffirmed Document has been changed only to reflect the new SAE Technical Standards BoardFormat.1. ScopeThis Report presents general information on over 50 alloys in which nickel eith
5、er predominates or is asignificant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Valuesgiven are in most cases average or nominal, and if more precise values are required the producer(s) should becontacted. This report does not cover the so-called “su
6、peralloys,“ or the iron base stainless steels. Refer toSAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels,respectively, for data on these alloys.2. References2.1 Applicable PublicationsThe following publications form a part of the specification to t
7、he extent specifiedherein. Unless otherwise indicated the lastest revision of SAE publications shall apply.2.1.1 SAE PUBLICATIONSAvailable from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.SAE J467Special Purpose AlloysSAE J405Chemical Compositions of SAE Wrought Stainless SteelsSAE J470c
8、Revised JUL76-2-TABLE 1SAE J470c Revised JUL76-3-TABLE 1 (CONTINUED)SAE J470c Revised JUL76-4-TABLE 1 (CONTINUED)SAE J470c Revised JUL76-5-TABLE 1 (CONTINUED)SAE J470c Revised JUL76-6-TABLE 1 (CONTINUED)SAE J470c Revised JUL76-7-TABLE 1 (CONTINUED)SAE J470c Revised JUL76-8-TABLE 2NOMINAL CHEMICAL CO
9、MPOSITIONSKey(1)No.1. See Key Number in each table for complete information on each alloy.Percent by WeightNi(2)2. Includes a small amount of cobalt which is counted as nickel.Cu Cr Fe Mn Si C Other1A 99.4 0.1 0.15 0.18 0.18 0.05 0.005 S1B 93.7 0.13 0.35 0.3 0.5 0.17 4.4 Al, 0.005 S, 0.63 Ti1C 99.98
10、 325(42) (85) (28.5) (240)11I A,B,C,D,E,F 241862 5171035 60-10 120130 197 (35125) (75150) (28.5) 11J A,C,E 2071000 4831035 35-0.5 B80 (30145) (70150) 12A A,C,D,E,F 3621242 6521476 52-13 152 (52.5180) (94.5214) (22) 12B A,C,D,E 276966 5171035 30-0.5 B82-100 (40140) (75150) 13A A,B,C,D,E,F 462 925 51
11、B96 215 81 (67) (134) (31.1) (60) 13B A,B,C,D,E,F 504 987 51 217 240(73) (143) (31.4) (177)14A A,B,C,D,E,F 414 766 52 B90 212 (60) (111) (30.8) KeyNo.AvailableForms(2)YieldStrength0.2%Offset106Pa(103psi)TensileStrength106Pa(103psi)Elongationin 50 mm(2 in)%Reductionof Area%HardnessModulusofElasticity
12、109Pa(106psi)EnduranceLimit108Cycles106Pa(103psi)Impactat R.T.Brinell3000 kg RockwellStandardIzodJ(ftlb)StandardCharpyJ(ftlb)(3) X6.9 X6.9 X6.9 X6.9 X1.356 X1.356SAE J470c Revised JUL76-15-14B A,B,C,D,E,F 462828 7591000 2460 B90-105 206 2831(67120) (110115) (29.8) (2123)14C A,B,C,D,E,F 462828 759100
13、0 2460 B90105 206 2831(67120) (110145) (29.8) (2123)14D A,B,C,D,E,F 380 780 50 65 192 B88 196 121 119-73(55) (113) (28.5) (89) (8854)14E A,B,C,D,E 345 690 50 57 160202 B82-92 193 150(50) (100) (28) (110)14F A,B,C,D,E,F 317 704 61 52 B84 (46) (102) 14G A,B,C,D,E,F 310 628 45 67 160 B84-90 193 (45) (9
14、1) (28) 15A A,B,C,D,E,F,G 179497 373545 43 B35-90 (2672) (5479) 15B A,B,C,D,E,F,G 186586 414690 40 124 (2785) (60100) (18) 15C A,B,C,D,E,F,G 152-566(22-82)380-662(55-96)40 1 Consult producers for more specific values.2 ARods and bars over 1/2 in dia.BForgingsCWire 1/2 in dia. max.DSheetEStripFTubing
15、GCastings3 Metric values shown were computed by use of these conversion factors.KeyNo.AvailableForms(2)YieldStrength0.2%Offset106Pa(103psi)TensileStrength106Pa(103psi)Elongationin 50 mm(2 in)%Reductionof Area%HardnessModulusofElasticity109Pa(106psi)EnduranceLimit108Cycles106Pa(103psi)Impactat R.T.Br
16、inell3000 kg RockwellStandardIzodJ(ftlb)StandardCharpyJ(ftlb)(3) X6.9 X6.9 X6.9 X6.9 X1.356 X1.356SAE J470c Revised JUL76-16-TABLE 5AVAILABLE SPECIFICATIONSAE J470c Revised JUL76-17-TABLE 6PRODUCERS3. Notes3.1 Marginial IndiciaThe change bar (l) located in the left margin is for the convenience of t
17、he user in locatingareas where technical revisions have been made to the previous issue of the report. An (R) symbol to the leftof the document title indicates a complete revision of the report.PREPARED BY THE SAE NONFERROUS METALS COMMITTEESuper-scriptNumeral(1)1. As shown in Table 1.Name and Addre
18、ss1 Huntington Alloys Inc., Huntington, WV 257202 Hoskins Manufacturing Co., 4445 Lawton Ave., Detroit, MI 482083 Wilber B. Driver Co., 1875 McCarter Highway, Newark, NJ 071044 Simonds Steel, Wallace Murray Corp., Lockport, NY 140945 Driver-Harris, Harrison, NJ 070296 Cyclops Corp., 650 Washington R
19、d., Pittsburgh, PA 152287 Carpenter Technology, Reading, PA 196038 Rolled Alloys, Inc., 5311 Concord Ave., Detroit, MI 482119 Kawecki Berylco Industries, Inc., 220 East 42nd St., New York, NY 1001710 Cabot Corp., Stellite Div., 1020 West Park Ave., Kokoma, IN 4690111 Wolverine Tube Div., UOP, Box 22
20、02, 2100 Market St., N.E., Decatur, AL 3560112 H. M. Harper Co., Morton Grove, IL 6005313 Indiana General, 407 Elm St., Valparaiso, IN 4638314 Arnold Engineering Co., Railroad Ave. and West, Box G, Marengo, IL 6015215 Colt Industries, Crucible Magnetic Div., Box 100, Elizabethtown, KY 42701SAE J470c
21、 Revised JUL76RationaleNot applicable.Relationship of SAE Standard to ISO StandardNot applicable.ApplicationThis Report presents general information on over 50 alloys in which nickel either predominatesor is a significant alloying element. It covers primarily wrought materials, and is not necessaril
22、y allinclusive. Values given are in most cases average or nominal, and if more precise values are requiredthe producer(s) should be contacted. This report does not cover the so-called “superalloys,“ or the ironbase stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, ChemicalCompositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.Reference SectionSAE J467Special Purpose AlloysSAE J405Chemical Compositions of SAE Wrought Stainless SteelsDeveloped by the SAE Nonferrous Metals Committee
