1、AEROSPACE STANDARD NUT, SELF LOCKING - SPLINE DRIVE, EXTENDED WASHER, UNS G87400, CADMIUM PLATE, MJ THREAD, METRIC MA3353Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elec
2、tronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 19
3、87-07NONCURRENT 1996-11 REAFFIRMED NONCURRENT 2006-05 REVISED 210-08 THIRD ANGLE PROJECTION CUSTODIAN: SAE E-25 REV.BFEDERAL SUPPLY CLASS 5310 MA3353SHEET 1 OF 3REV. BPROCUREMENT SPECIFICATION:MA1573SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate o
4、f technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time
5、itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/MA3353BRATIONALE CADMIUM PLATE NOTICE REVISED AND MOVED TO THE CORRECT PLACE AND GENERAL UP
6、DATING OF THE STANDARD FIGURE 1 NUT Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD MA3353SHEET 2 OF 3REV. BNUT, SELF LOCKING - SPLINE DRIVE, EXTENDED WASHER, UNS G87400, CADMIUM PLATE, MJ THREAD, METRIC TABLE 1 - DIMENSIONS PARTNO
7、 THREADTXXSPLINEDASH NO. AMAXBMAXCDMINMA3353-05 MA3353-06 MA3353-07 MA3353-08 MA3353-10 MA3351-12 MJ5 X 0.8-4H6H MJ6 X 1-4H5H MJ7 X 1-4H5H MJ8 X 1-4H5H MJ10 X 1.25-4H5H MJ12 X 1.25-4H5H 0708091012159.1 10.612.113.616.719.97.22 8.26 9.31 10.36 12.44 15.54 5.2 - 5.8 6.3 - 7.1 7.3 - 8.1 8.3 - 9.1 10.3
8、 - 11.1 12.3 - 13.1 8.3 9.8 11.312.815.718.8TABLE 1 - DIMENSIONS (CONTINUED) PARTNO. EMINFG Hh14 1/KMAXLMINAPPROX MASSkg/100MA3353-05 MA3353-06 MA3353-07 MA3353-08 MA3353-10 MA3353-12 1.81.81.81.82.02.60.130.150.180.200.250.300.100.100.100.100.130.136.64 - 7.00 7.74 - 8.10 8.74 - 9.10 9.97 - 10.40 1
9、2.57 - 13.00 14.57 - 15.00 5.4 5.7 6.7 7.9 10.012.01.31.42.02.73.13.50.172 0.243 0.323 0.428 0.717 1.362 1/ TOLERANCE GRADE TO ANSI B4.2-1978 NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUMAS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE NOTE
10、S: 1. MATERIAL: STEEL, AMS6322 (UNS G87400) 2. HEAT TREATMENT: HARDEN AND TEMPER TO PRODUCE THE HARDNESS IN NOTE 3. 3. HARDNESS: 35-40 HRC OR EQUIVALENT. 4. FINISH: CADMIUM PLATE PER AMS2400. DIMENSIONS ARE AFTER PLATING. 5. MAGNETIC PARTICLE INSPECTION: AMS2640 AFTER PLATING. ACCEPTANCE CRITERIA PE
11、R MA1573. 6. PROCUREMENT SPECIFICATION: MA1573. 7. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1 UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 3.2 MICROMETERS Ra. 8. BREAK EDGES 0.1 TO 0.4 UNLESS OTHERWISE SPECIFIED. 9. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982. ASME PUBLI
12、CATION 10. ALL LINEAR DIMENSIONS IN SI MILLIMETERS. 11. PRODUCT QUALIFICATION: QUALIFICATION TESTS IN ACCORDANCE WITH MA1573 SHALL BE PERFORMED BY THE MANUFACTURER PRIOR TO FIRST SHIPMENT OF PARTS. 12. DO NOT USE UNASSIGNED PART NUMBERS. Provided by IHSNot for ResaleNo reproduction or networking per
13、mitted without license from IHS-,-,-AEROSPACE STANDARD MA3353SHEET 3 OF 3REV. BNUT, SELF LOCKING - SPLINE DRIVE, EXTENDED WASHER, UNS G87400, CADMIUM PLATE, MJ THREAD, METRIC 13. AFTER OCTOBER 1996 PARTS ARE CADMIUM PLATED. 14. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF TH
14、E USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL
15、PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS, MA & AMS ARE SAE INTERNATIONAL PUBLICATIONS ANS I IS AMERICAN NATIONAL STANDARDS INSTITUTE PUBLICATION ASME ARE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATIONS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
