1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21567-5 SANS 1376-1:2008Edition 1.6SOUTH AFRICAN NATIONAL STANDARD Lights for motor vehicles Part 1: Incandescent lamps Published by Stand
4、ards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code +27 12 www.stansa.co.za Standards South Africa SANS 1376-1:2008 Edition 1.6 Table of changes Change No. Date Scope Amdt 1 1987 Amended to change the designation of cer
5、tain lamps. Amdt 2 1988 Amended to include an additional lamp category. Amdt 3 2001 Amended to include additional categories of lamp that are covered in SANS 20037. Amdt 4 2003 Amended to add information relating to the compulsory application of the standard, to add chromaticity coordinates for whit
6、e bulbs, and to change the definition of “acceptable”. Amdt 5 2006 Amended to include a conformity of production clause. Amdt 6 2008 Amended to add requirements for finished filament lamps emitting red light (3.6). Acknowledgement Standards South Africa wishes to acknowledge the valuable assistance
7、derived from publications of the following organizations: a) Deutsches Institut fr Normung; b) Economic Commission for Europe; and c) International Electrotechnical Commission. Foreword This South African standard was approved by National Committee StanSA TC 5120.71, Lighting and optics for traffic
8、and transport, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This document was published in June 2008. This document supersedes SANS 1376-1:2006 (edition 1.5). A vertical line in the margin shows where the text has been technically modi
9、fied by amendment No. 6. For the compulsory application of this standard the stringency level, the introduction date and any additional requirements, if needed, are published in the applicable compulsory specification in the Government Gazette. Amdt 4 SANS 1376 consists of the following parts, under
10、 the general title Lights for motor vehicles: Part 1: Incandescent lamps. Part 2: Headlights. Part 3: Secondary lights. SANS 1376-1:2008 Edition 1.6 1 Contents Page Acknowledgement Foreword 1 Scope. 3 2 Definitions 3 3 Requirements. 4 4 Marking 6 5 Sampling and compliance with part 1 of the specific
11、ation . 6 6 Inspection and methods of test 7 6.1 Inspection. 7 6.2 General conditions of testing 7 6.3 Measurement of dimensions 7 6.4 Aging test . 7 6.5 Colour test 7 6.6 Measurement of initial power and of initial luminous flux . 7 6.7 Life test. 8 Appendix A Applicable standards. 41 Appendix B Lu
12、minous centre and shape of lamp filaments 42 Appendix C Determination of internal dimensions of lamps . 43 SANS 1376-1:2008 Edition 1.6 2 This page is intentionally left blank SANS 1376-1:2008 Edition 1.6 3 Lights for motor vehicles Part 1: Incandescent lamps 1 Scope 1.1 This part of the specificati
13、on covers incandescent tungsten filament lamps of the following categories for use in motor vehicles and trailers: R2, H1, H2, H3, H4, P21W, P21/5W, R5W, R10W, C5W, C18W, C21W, T4W, W3W and W5W. Amdt 1; amdt 2 This specification also covers other categories of lamp that are covered in SANS 20037. Am
14、dt 3 NOTE The standards referred to in this part of the specification are listed in appendix A. 2 Definitions 2.1 For the purposes of this part of the specification the following definitions shall apply: acceptable acceptable to the authority administering this standard, or to the parties concluding
15、 the purchase contract, as relevant Amdt 4 aging operation of a new lamp for a period of one hour in order to stabilize its electrical characteristics before initial measurements are made category international designation describing the basic design of a standardized incandescent lamp, e.g. H1 or P
16、21/5W Amdt 1 defective lamp that fails in one or more respects to comply with the relevant requirements of this part of the specification dipped beam beam of light used to illuminate the road ahead of a vehicle without causing excessive glare or discomfort to other drivers (particularly oncoming dri
17、vers) and other road users initial luminous flux luminous flux emitted by a lamp and measured at the end of the aging period initial power power of a lamp measured at the end of the aging period SANS 1376-1:2008 Edition 1.6 4 life number of hours a lamp operates before the filament (or one of the fi
18、laments) “burns out“ light device that distributes, filters, or otherwise transforms the luminous flux from one or more lamps and that includes all the parts necessary for supporting, fixing, and protecting the lamp(s) lot not less than three and not more than 10 000 lamps of the same type, from the
19、 same manufacturer, and bearing the same marking, submitted at any one time for inspection and testing main beam beam of light used to illuminate the road over a long distance ahead of a vehicle reference axis axis defined with reference to a cap and to which the positions and dimensions of certain
20、parts of the lamp are referred reference luminous flux specified luminous flux to which a standard lamp is set when the lamp is used for the testing of a light reference plane plane defined with reference to a cap and to which the positions and dimensions of certain parts of the lamp are referred st
21、andard lamp lamp having an uncoloured bulb and reduced dimensional tolerances, used for the testing of lights test voltage voltage, measured at the lamp terminals, at which the electrical and photometric characteristics of a lamp are tested type of lamp type of lamp as determined by the category, th
22、e rated voltage, and the colour of the bulb 3 Requirements 3.1 Bulbs A lamp bulb shall be clean and free from defects such as scores or spots detrimental to service of the lamp (see 6.1). 3.2 Caps 3.2.1 Dimensions When measured in accordance with 6.3, a lamp shall be found to have a cap complying wi
23、th the relevant lamp cap data sheet of IEC 60061-1, as specified on the relevant lamp data sheet (see 3.9). 3.2.2 Securing of caps A cap shall be firmly secured to a bulb. SANS 1376-1:2008 Edition 1.6 5 3.3 Aging When tested in accordance with 6.4, a lamp shall not become inoperative during the agin
24、g period. 3.4 Filament shape and position When determined in accordance with 6.3 (see also appendices B and C), the geometric shape and orientation of a filament shall approximate to that in the drawing(s) given on the relevant data sheet. A filament shown on the data sheet to be straight shall fit
25、into an imaginary straight coaxial cylinder with diameter D = (1,2d + 0,1f), where d is the filament diameter and f is the filament length. 3.5 Lamp dimensions External and internal lamp dimensions, when determined in accordance with 6.3, shall conform to those given in the drawing and the table on
26、the relevant lamp data sheet(s) (see 3.9). NOTE Some guidelines for the measurement of lamp dimensions are given in appendices B and C. 3.6 Colour A lamp bulb shall be uncoloured (white). Amdt 4 When determined in accordance with 6.5, the chromaticity coordinates shall be within the area bounded by
27、the lines connecting the points on the CIE chromaticity diagram, having the following (xy) coordinates: (0,310 0,348); (0,310 0,283); (0,443 0,382); (0,500 0,440) and (0,453 0,440). Amdt 4 If a yellow bulb is allowed on the lamp data sheet, the chromaticity coordinates shall be within the area given
28、 by (0,543 0,455); (0,524 0,443); (0,465 0,500) and (0,480 0,518). Amdt 4 Limits of finished filament lamps emitting red light shall be as follows: a) Limit towards yellow: y 0,335 b) Limit towards purple: y 0,980 Amdt 6 3.7 Initial power and initial luminous flux When measured in accordance with 6.
29、6, the initial power and the initial luminous flux of a lamp shall conform to the appropriate values given on the relevant data sheet. 3.8 Life When tested in accordance with 6.7, the average life of a sample of lamps shall be not less than the appropriate value given on the relevant data sheet. 3.9
30、 Data sheets The basic design, dimensions, and the electrical and photometric characteristics of a lamp shall be as given in figures 1-14 and tables 2-29, as appropriate. Lamps not covered by these figures and tables, shall comply with the appropriate lamp data sheets of annex I of SANS 20037. Amdt
31、3 SANS 1376-1:2008 Edition 1.6 6 4 Marking 4.1 Each lamp shall be legibly and durably marked with the following information: a) the manufacturers name or registered trade name or registered trademark or any combination of these; b) the lamp category; c) the rated voltage; and d) the rated power or,
32、in the case of a dual filament lamp, the rated power of each filament in the sequence: principal filament, secondary filament. 5 Sampling and compliance with part 1 of the specification NOTE This section applies to the sampling for inspection and testing before acceptance or rejection of single lots
33、 (consignments) in cases where no information about the implementation of quality control or testing during manufacture is available to help in assessing the quality of the lot. 5.1 Sampling The following sampling procedure shall be applied in determining whether a lot complies with the relevant req
34、uirements of this part of the specification. The sample so taken shall be deemed to represent the lot. From the lot take at random the number of lamps given in column 2 of table 1 relative to the appropriate lot size given in column 1. Table 1 Sampling 1 2 3 4 Acceptance number Lot size, lamps Sampl
35、e size, lamps Inspection Testing (other than for the life test) 3 8 9 15 16 25 2 3 5 0 0 0 0 0 1 26 50 51 90 91 150 8 13 20 1 1 2 1 2 3 151 280 281 500 501 1 200 32 50 80 3 5 7 5 7 10 1 201 3 200 3 201 10 000 125 200 10 14 14 21 5.2 Compliance with part 1 of the specification The lot shall be deemed
36、 to comply with the requirements of this part of the specification if, on inspection and testing of the sample taken in accordance with 5.1, a) the number of defectives found on inspection (see 6.1) does not exceed the relevant acceptance number given in column 3 of table 1, SANS 1376-1:2008 Edition
37、 1.6 7 b) the number of defectives found in respect of the remaining requirements (other than that for life) considered together, does not exceed the relevant acceptance number given in column 4 of table 1, and c) the average life of the sample tested is not less than 90 % of the value given on the
38、relevant data sheet. 5.3 Conformity of production Amdt 5 Tests undertaken to check for conformity of production shall be conducted in accordance with the conformity of production clause of SANS 20037. Amdt 5 6 Inspection and methods of test 6.1 Inspection Visually examine the lamp for compliance wit
39、h the requirements of 3.1, and the relevant requirements of 3.6 and section 4. 6.2 General conditions of testing 6.2.1 Supply voltage stabilization Unless otherwise specified, maintain the test voltage within 0,2 %. 6.2.2 Accuracy of measuring instruments Carry out measurements with instruments of a
40、n accuracy appropriate to the requirements. (At least class 0.2, i.e. 0,2 % of full-scale deflection.) 6.3 Measurement of dimensions Using acceptable measuring instruments, check the dimensions of the lamp for compliance with the requirements of 3.2.1, 3.4, and 3.5. (See also appendices B and C.) 6.
41、4 Aging test Age the lamp in a horizontal position for a period of 1 h at the appropriate test voltage given on the relevant data sheet. Age each filament of a dual filament lamp separately. In the case of dual filament lamps for headlights, age the dipped beam filament first, and in the case of oth
42、er dual filament lamps, age the main filament first. Check for compliance with the requirement of 3.3. 6.5 Colour test Use a spectrophotometer or other equally suitable colour-measuring device to determine the chromaticity co-ordinates of the light emitted by a lamp with a yellow bulb, and check for
43、 compliance with the requirements of 3.6. 6.6 Measurement of initial power and of initial luminous flux Operate the lamp in a horizontal position at the appropriate test voltage given on the relevant data sheet, until the lamp has stabilized. Measure by means of suitable instruments, the initial pow
44、er and the initial luminous flux of the lamp and check for compliance with the requirements of 3.7. SANS 1376-1:2008 Edition 1.6 8 6.7 Life test Mount 15 lamps in a horizontal position with a spacing of at least 50 mm between lamps. (If the sample size is less than 15, use all the lamps in the sampl
45、e.) Operate the lamps at the appropriate test voltage given on the relevant data sheet, using a supply voltage which is regulated within 1 %. (If an a.c. supply is used, it must have a frequency in the range 40-60 Hz.) Operate the lamps according to the relevant switching cycle given below: a) R2 an
46、d H4 lamps. Operate the filaments alternately. Operate the dipped beam filament continuously for 15 h and the main beam filament for 7,5 h in each 24 h period with 45 min “off“-periods between operations. b) P21/5W lamps. Test the filaments separately. In each case switch the lamps off for 15 min tw
47、ice in every 24 h period. Amdt 1 c) P21W lamps. Switch the lamps on and off at a frequency of 1,5 Hz (“on“-time = “off“-time) for a period of 15 s. Leave them off for a further period of 15 s and repeat. =4testofdurationtotallampeachoflifeThe Amdt 1 d) All other lamps. Switch the lamps off for 15 mi
48、n twice in every 24 h period. Terminate the test after 1,25 times the life given on the relevant data sheet. Calculate the average life of the lamps in the test sample (omitting “off“ periods from the life of a lamp). Table 2 Dimensions, R2 lamps (See figure 1) 1 2 3 4 Tolerances mm Reference Dimens
49、ions mm Lamp of normal production Standard lamp a* b* c 0,6 0,2 0,5 0,35 0,35 0,30 0,15 0,15 0,15 d e f 0 28,5+1,8# 0,5 0,35 0,4 0,3 0,15 0,2 g lc* 0 5,5 0 0,5 1,5 1 30 0,3 0,5 0 30 * Q-Q15 0,75 (lc+ f) 1 30 0 30 Cap P45t-41 In accordance with IEC 60061-1 (Sheet 7004-95-3) * This dimension is determined at reference line AA. +28,8 for 24 V lamps. # 2,2 for 24 V lamps. The value for Q-Q applies to a standard lamp only. The dimensions of the shield shall be
