1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22404-2 SANS 51395-4:2009 Edition 1 EN 1395-4:2007 Edition 1SOUTH AFRICAN NATIONAL STANDARD Thermal spraying Acceptance inspection of ther
4、mal spraying equipment Part 4: Plasma spraying This national standard is the identical implementation of EN 1395-4:2007 and is adopted with the permission of CEN, rue de Strassart 36, B-1050 Brussels. WARNING Can only be used in conjunction with SANS 51395-1. Published by SABS Standards Division 1 D
5、r Lategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 51395-4:2009 Edition 1 EN 1395-4:2007 Edition 1 Table of changes Change
6、No. Date Scope National foreword This South African standard was approved by National Committee SABS TC 107, Metallic and other inorganic coatings, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in A
7、pril 2009. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN13954 January2007 ICS25.220.20 SupersedesEN1395:1996 EnglishVersion ThermalsprayingAcceptanceinspectionofthermalspraying equipmentPart4:
8、Plasmaspraying ProjectionthermiqueContrledacceptationdumatriel deprojectionthermiquePartie4:Projectionauplasma ThermischesSpritzenAbnahmeprfungenfrAnlagen zumthermischenSpritzenTeil4:Plasmaspritzen ThisEuropeanStandardwasapprovedbyCENon23December2006. CENmembersareboundtocomplywiththeCEN/CENELECInte
9、rnalRegulationswhichstipulatetheconditionsforgivingthisEuropean Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcerningsuchnational standardsmaybeobtainedonapplicationtotheCENManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeoffic
10、ialversions(English,French,German).Aversioninanyotherlanguagemadebytranslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCENManagementCentrehasthesamestatusasthe officialversions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Bulgaria,Cyprus,CzechRepublic,Denmark
11、,Estonia,Finland, France,Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Romania,Slovakia,Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG
12、ManagementCentre:ruedeStassart,36B1050Brussels 2007CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN13954:2007:EThis standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-4:2007 (E) 2 Contents Page
13、 Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principles of acceptance inspection4 5 Procedure of acceptance inspection.5 6 Designation 6 7 Inspection report6 Annex A (informative) Inspection report for plasma spraying equipment (initial test/retest).7 Bibliography 9 Thi
14、s standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-4:2007 (E) 3 Foreword This document (EN 1395-4:2007) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by
15、 DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2007, and conflicting national standards shall be withdrawn at the latest by July 2007. This document together with EN 1395-1, 1395-2, 13
16、95-3, 1395-5, 1395-6 and 1395-7 supersedes EN 1395:1996. EN 1395 consists of the following Parts, under the general title Thermal spraying Acceptance inspection of thermal spraying equipment: Part 1: General requirements; Part 2: Flame spraying including HVOF; Part 3: Arc spraying; Part 4: Plasma sp
17、raying; Part 5: Plasma spraying in chambers; Part 6: Manipulator systems; Part 7: Powder feed systems. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus,
18、 Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. This standard may only be used and printed b
19、y approved subscription and freemailing clients of the SABS. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-4:2007 (E) 4 1 Scope This European Standard specifies requirements for the acceptance inspection of thermal spraying equipment,
20、 in this case plasma spraying, used in spray jobs to produce thermally sprayed coatings of reproducible quality. This part should be used in conjunction with EN 1395-1, which includes general requirements and explanations of procedures. 2 Normative references The following referenced documents are i
21、ndispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 657:2005, Thermal spraying Terminology, classification EN 1274:2004, Thermal spraying
22、Powders Composition, technical supply conditions EN 1395-7, Thermal spraying Acceptance inspection of thermal spraying equipment Part 7: Powder feed systems 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 657:2005 and the following apply. 3.1 high vol
23、tage ignition device unit that generates a high voltage (kV) and low current (mA) between the electrodes of the plasma spraying torch in order to ignite the arc 4 Principles of acceptance inspection 4.1 General The following clauses reveal state of the art technology in thermal spray equipment and t
24、he minimum requirements concerning a stable parameter setting and maintenance according to the classes given in Annex A. 4.2 High-voltage ignition device Other components and functions of the spraying equipment and other machines and/or equipment operated near by to the spraying equipment shall not
25、be affected by operation of the high-voltage ignition device. 4.3 Plasma gases The plasma spraying equipment shall be designed and installed in such a manner, that safe operation with plasma gases specified by the user will be achieved. 4.4 Plasma spray nozzle Processing of the spraying powder shall
26、 be possible without producing any disturbing deposits on and/or in the nozzle. Nozzles with different shapes and powder ports (internal or external) may be used for special applications. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-
27、4:2007 (E) 5 4.5 Spraying powder feed unit The powder feed unit shall be suitable for operation with the spraying equipment to be taken. The unit shall permit uniform processing of the powder required. It shall be possible to adjust the powder feed rate. The set points shall be constant and reproduc
28、ible, which is a precondition for this being adequate and constant carrier gas pressure and flow. 5 Procedure of acceptance inspection 5.1 General Spraying equipment shall be deemed properly supplied for all suitable spraying applications and for use with all suitable spraying materials required for
29、 the spraying process if it complies with the following requirements: 5.2 Electrical power Proof of the power rating required shall be given by 20 min of spraying with the parameters for aluminium oxide according to EN 1274:2004, 12.1 as recommended by the equipment manufacturer. During the test, th
30、e following items will be examined: electrical control; gas control; cooling water temperature. Limits of deviation: see Annex A; Class A and Class B. After stabilisation of arc and plasma, the deviation of the voltage (variable parameter) from the set point shall not exceed 3 % (Class A) and 12 % (
31、Class B). 5.3 High-voltage ignition device The high-voltage ignition device shall be deemed to meet the requirements given in 4.2 if it does not interfere with any appliances and functions of the spraying equipment during the test as specified in 5.2. There should be no excessive erosion wear visibl
32、e on the nozzle (spark). 5.4 Plasma gases The system shall be deemed to comply with the specified requirements if the following requirements are satisfied by the acceptance inspection. The values of gas pressure and gas flow shall not deviate by more than 1,5 % (Class A) and 5 % (Class B) from the s
33、et points over a 20 min period of spraying. If the secondary gas is the variable parameter, the deviations from the set point shall not exceed 3 % (Class A) and 12 % (Class B) after stabilisation. Setting the primary gas pressure and/or flow rate shall not affect the corresponding values of the seco
34、ndary gas and carrier gas and vice versa. 5.5 Plasma spray nozzle The nozzle shall be deemed to comply with the requirements specified in 4.4 if there are no disturbing deposits of spraying material on or in the nozzle when testing as specified in 5.2. This standard may only be used and printed by a
35、pproved subscription and freemailing clients of the SABS.EN 1395-4:2007 (E) 6 5.6 Powder feed unit The suitability of the system to process powders as specified in 4.5 shall be tested according to EN 1395-7. 6 Designation Acceptance inspection of the thermal spraying equipment for plasma spraying sh
36、all be designated as follows: Acceptance inspection according to EN 1395-4. 7 Inspection report An example for the inspection report is given in Annex A. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-4:2007 (E) 7 Annex A (informative)
37、 Inspection report for plasma spraying equipment (initial test/retest) The initial test/retest fulfils the requirements of the acceptance inspection according to EN 1395-4. User: . Manufacturer: Year of manufacture: Type of equipment:. Type of spraying gun: . Powder used for testing:. Type of powder
38、 feed unit: . Size range: CE-documentation complete: yes / no Change after 20 minute continuous testing Limit Evaluation actual value in % Item tested, where applicable Full scale Set point min. max. maximum deviation in % Class A Class B passed failed current A 1,5 5 Electrical power voltage V 1,5
39、5 pressure bar 1,5 5 Primary gas flow Nl/min 1 ) 1,5 5 pressure bar 1,5 5 Secondary gas flow Nl/min 1) 1,5 5 pressure bar 1,5 5 Carrier gas flow Nl/min 1) 1,5 5 flow l/min 5 10 Cooling water inlet temperature to spray gun C 5 C 10 C 1)Referred to temperature 0 C and normal pressure (1 013,25 hPa). T
40、his standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-4:2007 (E) 8 High-voltage ignition device (interferes with other devices or functions): yes / no Deposits: yes / no Nozzle disturbance: yes / no Time needed for stabilisation: . Automatic e
41、nergy shutdown: Lack of gas: yes / no Lack of cooling water: yes / no Limits of error of measuring instruments: % of set point (max. 5 %) Class 2,5 2) : yes / no Comments:. . . . . . The thermal spraying equipment has been accepted: yes / no Date: Inspectors signature:. Date: Customers signature: Da
42、te: Suppliers signature:. 2)Maximum permissible error expressed by percentage of measuring span. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-4:2007 (E) 9 Bibliography 1 EN 1395-1, Thermal spraying Acceptance inspection of thermal sp
43、raying equipment Part 1: General requirements SABSThis standard may only be used and printed by approved subscription and freemailing clients of the SABS. SABS Standards Division The objective of the SABS Standards Division is to develop, promote and maintain South African National Standards. This o
44、bjective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008). Amendments and Revisions South African National Standards are updated by amendment or revision. Users of South African National Standards should ensure that they possess the latest amendments or editions. The SABS continuously
45、strives to improve the quality of its products and services and would therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would inform the secretary of the technical committee responsible, the identity of which can be found in the foreword. Tel: +27 (0) 12 42
46、8 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual notification service, which ensures that subscribers automatically receive notification regarding amendments and revisions to South African National Standards. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za Buyi
47、ng Standards Contact the Sales Office for South African and international standards, which are available in both electronic and hardcopy format. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za South African National Standards are also available online from the SABS website
48、http:/www.sabs.co.za Information on Standards The Standards Information Centre provides a wide range of standards-related information on both national and international standards, and is the official WTO/TBT enquiry point for South Africa. The Centre also offers an individual updating service called INFOPLUS, which ensures that subscribers automatically receive notification regarding amendments to, and revisions of, international standards. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za Copyright
