SIS 65 00 51-1960 Method for the determination of shrinkage of fabrics when washed at 60 C《在60 ℃织物洗涤的收缩测定方法》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN ISO 293-2005 en Plastics - Compression moulding of test specimens of thermoplastic materials《塑料 热塑性材料试样的压模铸造 ISO 293-2004》.pdf

EN ISO 2931-2010 en Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of admittance《铝和铝合金 阳极氧化用导纳或阻抗测量法评定阳极氧化膜的封孔质量[代.pdf

EN ISO 2931-2018 en Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of admittance.pdf

EN ISO 294-1-1998 en Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 1 General Principles and Moulding of Multipurpose and Bar Test Specimens (Inc.pdf

EN ISO 294-1-2017 en Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1 General principles and moulding of multipurpose and bar test specimens.pdf

EN ISO 294-2-1998 en Plastics Injection moulding of test specimens of thermoplastic materials Part 2 Small tensile bars (Incorporates Amendment A1 2005)《塑料 热塑材料试样的注塑 第2部分 小拉伸棒 包含修改.pdf

EN ISO 294-3-2003 en Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 3 Small Plates《塑料 热塑性塑料材料试样的注入模制 第3部分 小型厚板材》.pdf

EN ISO 294-4-2003 en Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 Determination of moulding shrinkage《塑料 热塑性材料试样的注模塑法 第4部分 模塑收缩率的测定》.pdf

EN ISO 294-5-2013 en Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5 Preparation of standard specimens for investigating anisotropy《塑料 热塑材料试样的注塑.pdf