SIS 74 13 43 E-1969 Core drilling equipment Double-tube core barrels type BT (riged or swivel type) Lower end of inner tube《钻芯设备双管岩芯桶，BT型（锁具型或旋转型），内部管子的底部》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

ONORM M 1156-1994 Testing methods for foundry sands - Sampling and Splitting of samples《铸造用砂测试方法 抽样和样品分解》.pdf

ONORM M 1157-1-1994 Testing methods for foundry sands - Determination of moisture《铸造用砂测试方法 水分测定》.pdf

ONORM M 1157-2-1994 Testing methods for foundry sands - Determination of fines content《铸造用砂测试方法 细粒含量的测定》.pdf

ONORM M 1157-3-1994 Testing methods for foundry sands - Determination of grain size distribution (sieve grading)《铸造用砂测试方法 粒度分布测定（筛分级）》.pdf

ONORM M 1302 Teil 4-1983 Tolerances and ts general tolerances and limits for dimensions from 3150 mm (o 10000 mm《公差配合 尺寸从3150 mm到10000 mm的一般公差极限》.pdf

ONORM M 1302 Teil 5-1986 Tolerances and flts general tolerances and limits for sizes above 10000 mm to 25000 mm《公差配合 尺寸从10000 mm到25000 mm的一般公差极限》.pdf

ONORM M 1310-1992 ISO-System of limits and fits - Selection of tolerance classes for dimensions up to 500 mm《 ISO公差与配合系统 尺寸达500毫米的公差等级选择》.pdf

ONORM M 1312-1992 ISO-System of limits and fits - Selection of fits in the hole basis and shaft basis system of fits for dimensions up to 500 mm《 ISO 公差与配合系统 尺寸达500毫米的基孔制配合和基轴制配合选择.pdf

ONORM M 1315-2001 Geometrical product specifications - Datum referencing and drawing indications in casting forging drawings and machining drawings《几何产品规格 在铸造 锻造图纸及加工图纸的基准参考和图样表示》.pdf