SIS SS 14 80 10-1983 Powder metallurgy - Sintered steel《粉末冶金 SS 烧结钢80 10》.pdf

相关资源

YB T 5308-2006 粉末冶金用还原铁粉.pdf

JIS Z2503-2000 粉末冶金用粉末.取样.pdf

FZ T 92050-1995 粉末冶金轴承.pdf

HB 5441.1-1989 粉末冶金制品和粉末的性能测试测定金属粉末粒度的筛分法.pdf

HB 5441.7-1989 粉末冶金制品和粉末的性能测试渗透性烧结金属材料密度和开孔度的测试方法.pdf

HB 5441.8-1989 粉末冶金制品和粉末的性能测试烧结金属衬套径向压溃强度的测定.pdf

HB 5458-1990 粉末冶金铜基多孔轴承.pdf

JB T 10310-2001 摩托车离合器用粉末冶金从动齿轮技术条件.pdf

JB T 10310-2011 摩托车离合器用粉末冶金从动齿轮 技术条件.pdf

JB T 2798-1999 铁基粉末冶金烧结制品金相标准.pdf

猜你喜欢

NASA-TN-D-4983-1969 Full-scale wind-tunnel investigation of static longtudinal and lateral characteristics of a light twin-engine airplane《轻型双发动机飞机静态纵向和横向特性的全比例风洞研究》.pdf

NASA-TN-D-5054-1969 Experimental pressure distributions on a 120 degrees cone at Mach numbers from 2 96 to 4 63 and angles of attack from 0 degrees to 20 degrees《当马赫数为2 96至4 63且攻角为.pdf

NASA-TN-D-5095-1969 Noncavitating and cavitating performance of several low area ratio water jet pumps having throat lengths of 3 54 diameters《带有3 54直径咽喉区长度的若干低面积比的喷水泵不成穴和成穴性能》.pdf

NASA-TN-D-5102-1969 Large-scale tests of an airplane model with a double-delta wing including longitudinal and lateral characteristics and ground effects《带有双三角形机翼飞机模型的大型试验(包括纵向和横向特.pdf

NASA-TN-D-5153-1969 The use of pilot rating in the evaluation of aircraft handling qualities《飞机飞行品质评估对飞行员评级的使用》.pdf

NASA-TN-D-5204-1999 Pressure distributions on 140 degrees 160 degrees and 180 degrees cones at Mach numbers from 2 30 to 4 63 and angles of attack from 0 degrees to 20 degrees《当马赫数.pdf

NASA-TN-D-523-1960 Investigation of the flow in a rectangular cavity in a flat plate at a mach number of 3 55《当马赫数为3 55时 平板中举行空腔中气流的研究》.pdf

NASA-TN-D-5361-1969 Analysis of lateral-directional stability characteristics of a twin-jet fighter airplane at high angles of attack《在高攻角时 双喷气战斗机的横向航向稳定特性的分析》.pdf

NASA-TN-D-5364-1969 Wind-tunnel investigation of an STOL aircraft configuration equipped with an external-flow jet flap《装配有外流喷气襟翼的短距离起落飞机结构的风洞研究》.pdf