SIS SS-EN 10 083-1-1991 Steels for quenching and tempering Part 1 Technical delivery conditions for special steels《钢的淬火，回火 第1部分：特种钢的技术交付条件》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 6349-2005 Three-jaw drill chucks - Technical delivery conditions《三爪钻夹 交货技术条件》.pdf

DIN 635-1-2010 Rolling bearings - Radial spherical roller bearings - Part 1 Single row with cylindrical and tapered bore (Barrel roller bearing)《滚动轴承 径向球形滚柱轴承 第1部分 圆柱形和圆锥孔的单排(鼓形滚柱轴.pdf

DIN 635-2-2009 Rolling bearings - Radial spherical roller bearings - Part 2 Double row with cylindrical and tapered bore《滚动轴承 径向球形滚柱轴承 第2部分 带圆柱形和锥形孔的双列轴承 n》.pdf

DIN 6350-1-2010 Lathe chucks hand-operated - Centric clamp - Part 1 Cylindrical mounting recess《手动中心夹件的车床夹盘 第1部分 圆柱形安装凹槽》.pdf

DIN 6350-2-2010 Lathe chucks hand-operated - Centric clamp - Part 2 Mounting recess with 1 4 taper《手动车床卡盘的中心夹件 第2部分 带1 4锥度安装凹座》.pdf

DIN 6351-1-2010 Lathe chucks hand-operated - Jaws with centrical clamping individually adjustable - Part 1 Cylindrical mounting recess《手动车床卡盘 带中心夹合自调整的钳口 第1部分 圆柱形安装槽》.pdf

DIN 6351-2-2010 Lathe chucks hand-operated - Jaws with centrical clamping individually adjustable - Part 2 Mounting recess with 1 4 taper《手动车床卡盘 非自定心卡盘 第2部分 带1 4锥度安装槽 n》.pdf

DIN 6352-1-1968 Chuck backplates with 1 4 Locating Taper Basic Flanges《带1 4 定心锥的卡盘座板 基准法兰》.pdf

DIN 6353-2010 Lathe chucks power-operated without trough-hole - Cross tenon type jaw mounting《无通孔动力操作车床卡盘 十字榫式颚支架 》.pdf