SIS SS-EN 284-1992 Swap bodies of dass C Dimensions and general requirements《可折卸货厢 尺寸和一般要求》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D692-A2-1989 THERMOPLASTIC POLYESTER- ETHER ELASTOMER (TEEE) 55 DUROMETER D HARDNESS HEAT STABILIZED EXTRUSION MOLDING COMPOUND (Shown on WSK-M4D692-A1)《硬度为55 D的热塑性聚酯-乙醚.pdf

FORD WSK-M4D693-A1-2011 THERMOPLASTIC POLYESTER-ETHER ELASTOMER (TEEE) 55 DUROMETER D HARDNESS INJECTION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《硬度计显示硬度为D55的乙醚弹性体(T.pdf

FORD WSK-M4D693-A2-2011 THERMOPLASTIC POLYESTER-ETHER ELASTOMER (TEEE) 55 DUROMETER D HARDNESS BLACK INJECTION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD.pdf

FORD WSK-M4D694-A-2011 THERMOPLASTIC POLYESTER-ETHER ELASTOMER (TEEE) 63 DUROMETER D HARDNESS MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《硬度计显示硬度为D63的乙醚弹性体(TEEE)模塑材料热塑性.pdf

FORD WSK-M4D695-A-2010 POLYETHYLENE (PE) MOLDING COMPOUND HIGH DENSITY LOW MELT FLOW RATE TO BE USED WITH FORD WSS-M99P1111-A 《高密度低熔态流动性聚乙烯(PE)模塑材料 与福特WSS-M99P1111-A 一起使用》.pdf

FORD WSK-M4D696-A-2010 POLYETHYLENE (PE) MOLDING COMPOUND HIGH DENSITY OIL IMPREGNATED TO BE USED WITH FORD WSS-M99P1111-A 《油浸渍的高密度聚乙烯（PE）成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSK-M4D697-A1-2008 ABS POLYCARBONATE BLEND (ABS+PC) HIGH IMPACT STRENGTH HIGH HEAT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用丙烯腈-丁二烯-苯乙烯共聚物(ABS) 聚碳酸酯混合物(ABS.pdf

FORD WSK-M4D697-A2-2008 ABS POLYCARBONATE BLEND (ABS+PC) HIGH IMPACT STRENGTH HIGH HEAT MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M4D697-A1.pdf

FORD WSK-M4D697-A3-2008 ABS + POLYCARBONATE BLEND (ABS+PC) HIGH IMPACT STRENGTH HIGH HEAT MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯(ABS)+聚碳酸酯(ABS.pdf