SNI 3538-2011 Leather - Sheep goat wet blue leather - Specification《皮革 羊 山羊蓝湿革 产品规范》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

STAS SR ISO 806-1994 Aluminium oxide primarily uaed for the production of aluminium -Determination of loss of mass at 1000 degrees C and 1200 degrees C《主要用于生产铝的氧化铝．在1000摄氏度和1200摄氏度.pdf

STAS SR ISO 815+A1-1995 Rubber vulcanized or thermoplastic - Determination of compression set at ambient elevated or low temperatures《橡胶，硫化或热塑性．在常温，高温或低温下测定压定 》.pdf

STAS SR ISO 835-1-1996 Laboratory glassware - Graduated pipettes Part 1 General requirements《实验室玻璃器皿．分度滴管．第1部分：一般要求》.pdf

STAS SR ISO 857-1994 Welding brazing and soldering proceses Vocabulary《焊，硬钎焊和软焊过程．词汇表》.pdf

STAS SR ISO 868-1995 Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness)《塑料和硬橡胶．通过硬度计测定压痕硬度（肖氏硬度）》.pdf

STAS SR ISO 883-1994 Indexable harmetal (carbide) inserts with rounded corners without fixing hole - Dimensions《带圆角，没有固定孔的可加索引的硬金属 （硬质合金）刀片．尺寸 》.pdf

STAS SR ISO 900-1996 Aluminium oxide primarily used for the production of aluminium -Determination of titanium content - Diantipyrylmethane photometric method《主要用于铝制品生产的三氧化二铝．钛含量的测.pdf

STAS SR ISO 918-1994 Volatile organic liquids for industrial use - Determination of distillation characteristics《工业用挥发性有机化合物的液体．测定蒸馏特性 》.pdf

STAS SR ISO 928-1995 Spices and condiments — Determination of total ash《香料和调味品．总灰分测定 》.pdf