TCVN 7428-2004 Leather Physical and mechanical tests Determination of water resistance of heavy leathers《皮革 物理和机械试验 重皮革的耐水性测定》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN ISO 4543-1994 en Metallic and Other Non-Organic Coatings - General Rules for Corrosion Tests Applicable for Storage Conditions《金属和其他无机覆盖层 储存条件下腐蚀试验的一般规则(ISO 4543-1981)》.pdf

EN ISO 4545-1-2005 en Metallic materials Knoop hardness test Part 1 Test method《金属材料 努氏硬度试验 第1部分试验方法 ISO 4545-1-2005》.pdf

EN ISO 4545-1-2018 en Metallic materials - Knoop hardness test - Part 1 Test method.pdf

EN ISO 4545-2-2005 en Metallic materials Knoop hardness test Part 2 Verification and calibration of testing machines《金属材料 努氏硬度试验 第2部分 试验机的验证和校准 ISO 4545-2-2005》.pdf

EN ISO 4545-3-2005 en Metallic materials - Knoop hardness test - Part 3 Calibration of reference blocks《金属材料 努氏硬度试验 第3部分 参考块的校正 ISO 4545-3-2005》.pdf

EN ISO 4545-3-2018 en Metallic materials - Knoop hardness test - Part 3 Calibration of reference blocks.pdf

EN ISO 4545-4-2005 en Metallic materials - Knoop hardness test - Part 4 Table of hardness values《金属材料 努氏硬度试验 第4部分 硬度值表 ISO 4545-4-2005》.pdf

EN ISO 4566-1995 en Small Craft with Inboard Engine - Propeller Shaft Ends and Bosses with 1 10 Taper《舱内安装发动机的小型船舶 锥度为1-10螺旋浆轴端和尾轴毂(ISO 4566-1992)》.pdf

EN ISO 4577-1999 en Plastics - Polypropylene and Propylene-Copolymers - Determinations of Thermal Oxidative Stability in Air - Oven Method《塑料 聚丙烯和丙烯共聚物 空气中氧化热稳定性的测定 烘箱法》.pdf