TCVN 7556-3-2005 Health care solid waste incinerators Determination of the mass concentration of PCDD PCDF Part 3 Identification and quantification《医疗用固体废物焚化炉 PCDD PCDF的质量浓度测定 第3部分.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

NC 09-03-1968 Selection of metertela for dies《冲模材料选择》.pdf

NC 09-03-1984 Material Forming Selection of Materials for Dlea General Rules《材料成型 冲模材料选择 一般准则》.pdf

NC 09-04-10-1985 Unified Elements System of Molds Dies Stampers and Devices Machining Device Locknut with Fixed or Travelling Lever Main Dimensions《模具统一原理系统 冲模，压模和机械装置 模具 固定防松或控制杆 .pdf

NC 09-04-100-1988 Unified Element System of Moulds Dies Stampers and machining Devices Machining Devices Spheric Support Design Specifications《模具统一原理系统 冲模，压模和机械装置 机械装置 球状支撑 设计规格》.pdf

NC 09-04-101-1988 Unified Elements System of Moulds Dies Stampers and Macinig Devices Machining Device Milled Ring Nuts Design Specifications《模具统一原理系统 冲模，压模和机械装置 机械装置 滚花环螺母设计规格》.pdf

NC 09-04-102-1988 Unified Elements System of Moulds Dies Stampers and Machiníng Devices Machining Device Slotted Nut Design Specifications《模具统一原理系统 冲模，压模和机械装置 机械装置 带槽螺母 设计规格》.pdf

NC 09-04-104-1988 Unified Elements System of Moulds Dies Stampers and Machining Devices Devices Adjusting Slotted Screw Design Specifications《模具统一原理系统 冲模，压模和机械装置 机械装置 可调有槽螺丝钉 设计规格》.pdf

NC 09-04-109-1988 Unified Elements System of Moulds Dies Stampers and Machining Devices Devices Spheric ot Plain Flange Square Nut Design Specifications《模具统一原理系统 冲模，压模和机械装置 机械装置 凸方.pdf

NC 09-04-11-1985 Unified Elements System of Molds Dies Stampers and Devices Machining Device Locknut with Fixed or Travelling Lever Main Dimensions and Design Specifications《模具统一原理.pdf