TCVN 7699-2-5-2011 Environmental testing Part 2-5 Tests Test Sa Simulated solar radiation at ground level and guidance for solar radiation testing《环境试验 第2-5部分 试验 试验Sa 地面上模拟太阳辐射和太阳辐.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D718-A-2010 POLYCARBONATE (PC) FILM TRANSLUCENT TO BE USED WITH FORD WSS-M99P1111-A 《透明的聚碳酸酯(PC)膜 与福特WSS-M99P1111-A 一起使用[使用 福特WSS-M4D1053-A1 福特WSS-M4D1053-A2]》.pdf

FORD WSK-M4D718-A4-2010 POLYCARBONATE + POLYBUTYLENE THEREPHTALATE (PC+PBT) BLEND FILM TRANSLUCENT TO BE USED WITH FORD WSS-M99P1111-A 《聚碳酸酯+聚对苯二甲酸丁二醇酯混合物(PC+PBT)混合物半透明薄膜 与标准FOR.pdf

FORD WSK-M4D719-A-2006 POLYAMIDE (PA) 66 38% GLASS FIBER MINERAL REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A (Use WSK-M4D823-A)《38%玻璃纤维 矿物增强的聚酰胺66成型料 与标准FORD.pdf

FORD WSK-M4D720-A-2005 THERMOPLASTIC POLYETHER ESTER ELASTOMER (TEEE) 50 DUROMETER D HARDNESS MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《硬度为50 D的热塑性聚醚酯弹性体(TEEE)成型料 与标.pdf

FORD WSK-M4D721-A-2013 POLYETHYLENE (PE) MOLDING COMPOUND HIGH DENSITY MEDIUM MELT FLOW RATE TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSK-M4D722-A-2008 ABS 16% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯 16%玻璃纤维增强模塑料(和FORD WSS-M99P1111-A一起使用)(使用 FORD ESB-M4D483-.pdf

FORD WSK-M4D722-A2-2008 ABS 7 % GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《ABS 7%强化玻璃纤维模压塑料(与FORD WSS-M99P1111-A一起使用) (使用 FORD ESB-M4D483-A1 FOR.pdf

FORD WSK-M4D724-A1-2013 STYRENE MALEIC ANHYDRIDE (SMA) COPOLYMER RUBBER MODIFIED 20% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSK-M4D724-A2-2013 STYRENE MALEIC ANHYDRIDE (SMA) COPOLYMER RUBBER MODIFIED 20% GLASS FIBER 10% ACRYLIC REGRIND REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-.pdf