TS 1057-1972 CREEPAGE DISTANCES AND CLEARANCES N AIR《空气中爬电距离和电气间隙》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN ISO 8734-1997 en Parallel Pins of Hardened Steel or Martensitic Stainless Steel (Dowel Pins)《淬硬钢和马氏体不锈钢(定位销)圆柱销 ISO 8734-1997 代替EN 28734-1992》.pdf

EN ISO 8735-1997 en Parrallel Pins with Internal Thread of Hardened Steel or Martensitic Stainless Steel《淬硬钢或马氏体不锈钢内螺纹圆柱销 ISO 8735-1997 代替EN 28735-1992》.pdf

EN ISO 8739-1997 en Grooved Pins - Full-Length Parallel Grooved with Pilot《槽销 带导杆及全长平行沟槽 ISO 8739-1997 代替EN 28739-1992》.pdf

EN ISO 8740-1997 en Grooved Pins - Full-Length Parallel Grooved with Chamfer《槽销 带倒角及全长平行沟槽 代替EN 28740-1992 ISO DIS 8740-1997》.pdf

EN ISO 8741-1997 en Grooved Pins - Half-Length Reverse-Taper Grooved《槽销 半长倒锥槽 ISO 8741-1997 代替EN 28741-1992》.pdf

EN ISO 8742-1997 en Grooved Pins - One-Third-Length Centre Grooved《槽销 中部槽长为1 3全长 ISO 8742-1997 代替EN 28742-1992》.pdf

EN ISO 8743-1997 en Grooved Pins - Half-Length Centre Grooved《槽销 中部槽长为1 2全长 代替EN 28743-1992》.pdf

EN ISO 8744-1997 en Grooved Pins - Full-Length Taper Grooved《槽销 全长锥槽 ISO 8744-1997 代替EN 28744-1992》.pdf

EN ISO 8745-1997 en Grooved Pins - Half-Length Taper Grooved《槽销 半长锥槽 ISO 8745-1997 代替EN 28745-1992》.pdf