UL 2040-2015 UL Standard for Safety Folding Rollaway Tables (Second Edition)《折叠桌的UL安全标准 (第二版)》.pdf

上传人:wealthynice100 文档编号:1067783 上传时间:2019-04-02 格式:PDF 页数:14 大小:565.86KB
下载 相关 举报
UL 2040-2015 UL Standard for Safety Folding Rollaway Tables (Second Edition)《折叠桌的UL安全标准 (第二版)》.pdf_第1页
第1页 / 共14页
UL 2040-2015 UL Standard for Safety Folding Rollaway Tables (Second Edition)《折叠桌的UL安全标准 (第二版)》.pdf_第2页
第2页 / 共14页
UL 2040-2015 UL Standard for Safety Folding Rollaway Tables (Second Edition)《折叠桌的UL安全标准 (第二版)》.pdf_第3页
第3页 / 共14页
UL 2040-2015 UL Standard for Safety Folding Rollaway Tables (Second Edition)《折叠桌的UL安全标准 (第二版)》.pdf_第4页
第4页 / 共14页
UL 2040-2015 UL Standard for Safety Folding Rollaway Tables (Second Edition)《折叠桌的UL安全标准 (第二版)》.pdf_第5页
第5页 / 共14页
点击查看更多>>
资源描述

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 2040 Folding Rollaway TablesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRO

2、DUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Folding Rollaway Tables, UL 2040 Second Edition, Dated February 11, 2015 SUMMARY OF TOPICS This new edition of ANSI/UL 2040 is being issued to reect the rst time ANSI approval of the Standard. No changes in the requirement

3、s are involved. The requirements are substantially in accordance with Proposal(s) on this subject dated July 11, 2014. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recor

4、ding, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, c

5、onsequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall UL

6、s liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (inclu

7、ding reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of th

8、e Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. FEBRUARY 11, 2015 UL 2040

9、tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 11, 2015 UL 2040 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 11, 2015 1 UL 2040 Stand

10、ard for Folding Rollaway Tables First Edition October, 2000 Second Edition February 11, 2015 This ANSI/UL Standard for Safety consists of the Second Edition. The most recent designation of ANSI/UL 2040 as an American National Standard (ANSI) occurred on February 10, 2015. ANSI approval for a standar

11、d does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development

12、 System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. CO

13、PYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 2040-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 11, 2015 FOLDING ROLLAWAY TABLES - UL 2040 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODU

14、CTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 Units of Measurement .4 3 Undated References 4 4 Terminology 4 CONSTRUCTION 5 General 4 6 Materials .5 PERFORMANCE 7 Tip Over Test .5 8 Tip Stability Test 6 9 Endurance Test .6 10 Load Stability Test .7 11 Bench Stre

15、ngth Test .7 12 Seat Strength Test .7 13 Wheel, Roller, or Caster Securement Test 7 14 Radiant Panel Flame Spread Test .7 14.1 Test criteria .7 14.2 Test specimens .8 MARKINGS 15 General .8 FEBRUARY 11, 2015 FOLDING ROLLAWAY TABLES - UL 2040 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPROD

16、UCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements apply to folding rollaway tables. The folding tables may have integral benches or stool seating. 1.2 These requirements do not apply to any electrical circuitry integral to or provided with a folding rollaw

17、ay table. The requirements of the standard covering the intended electrical product to be used with a folding rollaway table shall be applicable to any electrical circuits in the folding rollaway table. Electrical devices shall comply with the requirements for such devices. For example, attachment p

18、lugs and receptacles shall comply with the requirements in the Standard for Attachment Plugs and Receptacles, UL 498. Where the requirements of more than one standard are applicable, the most severe requirements shall apply. 2 Units of Measurement 2.1 Values stated without parentheses are the requir

19、ement. Values in parentheses are explanatory or approximate information. 3 Undated References 3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 4 Terminology 4.1 The phrase

20、table or tables , where used in this Standard, generally references any product considered under the scope of these requirements. CONSTRUCTION 5 General 5.1 A folding rollaway table shall be constructed so that: a) User assembly and normal use do not result in a risk of re or injury to persons; and

21、b) The materials and components are used within their mechanical and ammability limits. 5.2 Sharp edges shall not be accessible during user assembly or normal use. An accessible edge shall be smooth and well rounded to reduce the risk of a cut-type injury when contacted during user assembly or norma

22、l use. FEBRUARY 11, 2015 FOLDING ROLLAWAY TABLES - UL 2040 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 6 Materials 6.1 Polymeric material used for seats and/or edging in the construction of a folding rollaway table shall have a minimum

23、ammability classication of HB. The ammability classication is to be determined by tests described in the Standard for Tests for Flammability of Plastic Materials for Parts in Devices and Appliances, UL 94. A material classied using 1/8-inch (3.2-mm) thick bar specimens is not prohibited from being u

24、sed in thicknesses less than 1/8 inch in the folding rollaway table. Exception: The following materials are exempt from the requirements of 6.1: a) Wheels, casters, and caster inserts. b) External accessories that are not permanently attached to the folding rollaway table, such as a screwdriver, con

25、tainer of lubricating oil, and similar accessories. c) Small parts that satisfy all of the following: 1) The maximum volume does not exceed 0.122 inch 3 (2 cm 3 ); and 2) The maximum dimension does not exceed 1.18 inches (3 cm). d) Polymeric material of maximum 0.010 inch (0.254 mm) thickness. PERFO

26、RMANCE 7 Tip Over Test 7.1 When the folding rollaway table is folded in the upright storage position a force shall be applied at a position 5 ft. (1.52 m) above the oor or at the topmost edge, whichever is lower. The minimum force to tip the table over shall be one-fth of the total weight of the tab

27、le or 56 lb (25.4 kg), whichever is less. Exception: Folding rollaway tables intended to be secured to the oor, walls or other xed structural parts of a building are not required to comply with this requirement. 7.2 The test is to be conducted on a fully assembled table including benches, seats, sto

28、ols, backrests, and other table parts, under the following conditions: a) With the legs, wheels, casters, or similar means of support arranged in the position most likely to result in tip-over such as turning the caster so that the caster axle is under the table frame versus outside of the frame are

29、a. b) With the legs, wheels, casters, or similar means of support blocked by means of a steel bar 1/4 inch (6.4 mm) thick, 1 inch (25.4 mm) wide, that extends 2 inches (50.8 mm) beyond each leg and/or caster placed under the wheel. The steel bar shall be placed under one or more wheels to prevent th

30、e table from rolling. c) When the folding rollaway table is provided with a locking means to keep it folded in the storage or transport position and the lock can be disengaged without the use of tools to close the table tighter, the lock shall be disengaged and the table shall be closed to its tight

31、est upright position possible when evaluated. FEBRUARY 11, 2015 FOLDING ROLLAWAY TABLES - UL 2040 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 8 Tip Stability Test 8.1 When the folding rollaway table is folded in the upright storage posi

32、tion and placed at the center of a plane inclined to make an angle of 10 degrees with the horizontal, it shall not tip over. Exception: Folding rollaway tables intended to be secured to the oor, walls or other xed structural parts of a building are not required to comply with this requirement. 8.2 T

33、he test shall be conducted on a fully assembled table including benches, seats, stools, backrests, and other table parts, under the following conditions: a) With the legs, wheels, casters, or similar means of support arranged in the position most likely to result in tip-over such as turning the cast

34、er so that the caster axle is under the table frame versus outside of the frame area. b) With the legs, wheels, casters, or similar means of support blocked by means of a steel bar 1/4 inch (6.4 mm) thick, 1 inch (25.4 mm) wide, that extends 2 inches (50.8 mm) beyond each leg and/or caster placed un

35、der one or more of the wheels so that the folding rollaway table does not roll or slide on the inclined plane. c) When the folding rollaway table is provided with a locking means to keep it folded in the storage or transport position and the lock can be disengaged without the use of tools to close t

36、he table tighter, the lock shall be disengaged and the table shall be closed to its tightest upright position possible when evaluated. 9 Endurance Test 9.1 A sample of the fully assembled folding table including benches, seats, stools, backrests, and other table parts is to be subjected to 6000 cycl

37、es of normal operation of the hinge and locking mechanism. The hinge and lock mechanism shall remain operable at the conclusion of the cycling. 9.2 The folding table is to be assembled and operated in accordance with the manufacturers instructions. 9.3 The table is to be in the fully opened position

38、 and all locks, if provided, fully engaged. The locks are to be unlocked and the folding rollaway table is to be folded into the upright storage position. If a lock is provided to keep the table in the folded position, it is to be fully engaged. The locks are to then to be unlocked and the folding r

39、ollaway table is to be unfolded and placed into the open position. This is one cycle. 9.4 The cycle test may be conducted manually or automated. FEBRUARY 11, 2015 FOLDING ROLLAWAY TABLES - UL 2040 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FRO

40、M UL 10 Load Stability Test 10.1 A sample of each type of fully assembled table is to be subjected to a 300-lb (136-kg) load concentrated in a 1 square ft (0.09 square m) area of the table. The load is to be moved slowly over the entire surface of the table. The table shall not overturn or have any

41、visible damage to the structure. 11 Bench Strength Test 11.1 When a table is provided with benches, each size, style and type of bench is to be subjected to a distributed load. The load will be based on 250-lb (114-kg) load times the number of people intended to t on each bench. The bench shall with

42、stand the load without visible damage for one minute. 12 Seat Strength Test 12.1 When a table is provided with seats, each size, style and type of seat is to be subjected to a 250-lb (114-kg) distributed load. The seat shall withstand the load without visible damage for one minute. 13 Wheel, Roller,

43、 or Caster Securement Test 13.1 A wheel, roller, or caster shall be capable of withstanding a 5-lbf (22-N) pull applied as described in 13.2. 13.2 The 5-lbf (22-N) pull is to be applied by a weight or a steady pull for a period of 1 minute in any direction permitted by the construction of the parts.

44、 The force is to be applied with the specimen at room temperature. The wheel, roller, or caster shall not pull free from its securing means. 14 Radiant Panel Flame Spread Test 14.1 Test criteria 14.1.1 The ame spread index of a table top and bench material shall be determined in accordance with the

45、Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source, ASTM E162. 14.1.2 The ame spread index shall be less than 200. 14.1.3 This method provides a laboratory test procedure for measuring and comparing the surface ammability of materials when exposed to a pres

46、cribed level of radiant heat energy. This method is intended to measure surface burning characteristics when exposed to re. FEBRUARY 11, 2015 FOLDING ROLLAWAY TABLES - UL 2040 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 14.2 Test specim

47、ens 14.2.1 Four test specimens, 18 inches (45.7 cm) in length by 6 inches (15.2 cm) in width, in the minimum and maximum thicknesses, are to be tested covering the thickness range to be considered. Specimens in intermediate thicknesses are also to be provided and shall be tested when the results obt

48、ained on the minimum or maximum thicknesses indicate inconsistent test results. 14.2.2 Material Ranges When a material is to be considered in a range of colors, densities, melt ows, or reinforcement, four specimens representing these ranges are also to be provided. 14.2.3 Four specimens in the natur

49、al and in the most heavily pigmented dark color are to be provided and considered representative of the color range, when the burning characteristics are essentially the same. In addition, a set of specimens is to be provided in the heaviest organic pigment loading, unless the most heavily pigmented dark color includes the highest organic pigment level. When certain color pigments (for example, red, yellow, or other color types) are known to affect ammability characteristics, they are also to be provided. 1

展开阅读全文
相关资源
猜你喜欢
  • EN ISO 4048-2008 en Leather - Chemical tests - Determination of matter soluble in dichloromethane and free fatty acid content《皮革 化学试验 二氯甲烷中可溶物质和游离脂肪酸含量的测定》.pdf EN ISO 4048-2008 en Leather - Chemical tests - Determination of matter soluble in dichloromethane and free fatty acid content《皮革 化学试验 二氯甲烷中可溶物质和游离脂肪酸含量的测定》.pdf
  • EN ISO 4049-2009 en Dentistry - Polymer-based restorative materials《牙科学 聚合物基修复材料》.pdf EN ISO 4049-2009 en Dentistry - Polymer-based restorative materials《牙科学 聚合物基修复材料》.pdf
  • EN ISO 4063-2010 en Welding and allied processes - Nomenclature of processes and reference numbers《环境管理 环境传播 导则和实例》.pdf EN ISO 4063-2010 en Welding and allied processes - Nomenclature of processes and reference numbers《环境管理 环境传播 导则和实例》.pdf
  • EN ISO 4064-1-2014 en Water meters for cold potable water and hot water - Part 1 Metrological and technical requirements《冷饮用水表和热水表 第1部分 计量和技术要求(ISO 4064-1 2014)》.pdf EN ISO 4064-1-2014 en Water meters for cold potable water and hot water - Part 1 Metrological and technical requirements《冷饮用水表和热水表 第1部分 计量和技术要求(ISO 4064-1 2014)》.pdf
  • EN ISO 4064-1-2017 en Water meters for cold potable water and hot water - Part 1 Metrological and technical requirements.pdf EN ISO 4064-1-2017 en Water meters for cold potable water and hot water - Part 1 Metrological and technical requirements.pdf
  • EN ISO 4064-2-2014 en Water meters for cold potable water and hot water - Part 2 Test methods (ISO 4064-2 2014)《冷饮用水表和热水表 第2部分 测试方法(ISO 4064-2 2014)》.pdf EN ISO 4064-2-2014 en Water meters for cold potable water and hot water - Part 2 Test methods (ISO 4064-2 2014)《冷饮用水表和热水表 第2部分 测试方法(ISO 4064-2 2014)》.pdf
  • EN ISO 4064-2-2017 en Water meters for cold potable water and hot water - Part 2 Test methods.pdf EN ISO 4064-2-2017 en Water meters for cold potable water and hot water - Part 2 Test methods.pdf
  • EN ISO 4064-3-2014 en Water meters for cold potable water and hot water - Part 3 Test report format《冷饮用水表和热水表 第3部分 试验报告格式(ISO 4064-3 2014)》.pdf EN ISO 4064-3-2014 en Water meters for cold potable water and hot water - Part 3 Test report format《冷饮用水表和热水表 第3部分 试验报告格式(ISO 4064-3 2014)》.pdf
  • EN ISO 4064-4-2014 en Water meters for cold potable water and hot water - Part 4 Nonmetrological requirements not covered in ISO 4064-1《冷饮用水表和热水表 第4部分 不包括在ISO 4064-1中的非计量要求(ISO 406.pdf EN ISO 4064-4-2014 en Water meters for cold potable water and hot water - Part 4 Nonmetrological requirements not covered in ISO 4064-1《冷饮用水表和热水表 第4部分 不包括在ISO 4064-1中的非计量要求(ISO 406.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1