1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 60730-2-9 Automatic Electrical Controls for Household and Similar Use Part 2-9: Particular Requirements for Temperature Sensing ControlsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REP
2、RODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Automatic Electrical Controls for Household and Similar Use Part 2-9: Particular Requirements for Temperature Sens
3、ing Controls, UL 60730-2-9 Third Edition, Dated October 13, 2010 Summary of Topics These revisions are being issued to adopt the requirements covered by Amendment No. 1 of IEC 60730-2-9 and to adopt the North American National Differences to this IEC Amendment. THE STANDARDS TECHNICAL PANEL FOR UL 6
4、0730-2-9 HAS DETERMINED THAT AS OF OCTOBER 19, 2018, THE FIRST EDITION OF UL 60730-2-9 AND THE TWELFTH EDITION OF UL 873 WILL BE WITHDRAWN AND MAY BE USED TO DETERMINE A NEWLY SUBMITTED PRODUCTS COMPLIANCE UNTIL THIS DATE. The revised requirements are substantially in accordance with Proposal(s) on
5、this subject dated March 8, 2013. For further information regarding Summary of Requirements, please visit https:/. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. All rights reserved. No part of this publication m
6、ay be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited t
7、o, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use th
8、is Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safet
9、y agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The
10、 requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the preface. The prior text for requirements that have been revised and that have a future effective date are lo
11、cated after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. The following table lists the future effective dates with the corresponding reference. AUGUST 16, 2013 UL 60730-2-9 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FR
12、OM UL Future Effective Date Reference October 19, 2018 Third Edition AUGUST 16, 2013 UL 60730-2-9 tr2UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 13, 2010 (Title Page Reprinted: August 16, 2013) 1 UL 60730-2-9 Standard for Automat
13、ic Electrical Controls for Household and Similar Use Part 2-9: Particular Requirements for Temperature Sensing Controls Prior to the rst edition of UL 60730-2-9, the requirements for the products covered by this Standard were included in UL 8730-2-9. First Edition January, 2003 Third Edition October
14、 13, 2010 This ANSI/UL Standard for Safety consists of the Third Edition including revisions through August 16, 2013. The most recent designation of ANSI/UL 60730-2-9 as an American National Standard (ANSI) occurred on August 16, 2013. ANSI approval for a standard does not include the Cover Page, Tr
15、ansmittal Pages, Title Page, Preface, or effective date information. The National Difference Page and IEC Foreword are also excluded from the ANSI approval of IEC-based standards. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be
16、submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and righ
17、ts regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2013 UNDERWRITERS LABORATORIES INC. ANSI/UL 60730-2-9-2013UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 16, 2013 UL 60730-2-9 2 No Text on Th
18、is PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface (UL) 8 NATIONAL DIFFERENCES .9 FOREWORD . 10 1 Scope and normative references .14 1.5 Normative references 14 2 Denitions 15 2.2 Denitions of types of control according
19、to purpose 15 2.3 Denitions relating to the function of controls .17 2.5 Denitions of types of control according to construction 17 3 General requirements 17 4 General notes on tests .17 4.1 Conditions of test 17 4.2 Samples required 18 5 Rating 18 6 Classication 18 6.4 According to features of auto
20、matic action .18 6.7 According to ambient temperature limits of the switch head .19 6.15 According to construction .19 7 Information 19 7.2 Methods of providing information 20 8 Protection against electric shock .21 9 Provision for protective earthing .21 10 Terminals and terminations 21 11 Construc
21、tional requirements 21 11.1 Materials 22 11.3 Actuation and operation .22 11.4 Actions 22 11.6 Mounting of controls 25 11.101 Time factor 26 12 Moisture and dust resistance .26 12.101 Refrigeration controls .26 13 Electric strength and insulation resistance .27 14 Heating 27 15 Manufacturing deviati
22、on and drift .30 15.5.6CDV.1 Fan/heat sequencer Initial time-calibration test I 31 15.5.6DDV.1 Fan/heat sequencer Initial time-calibration test II 32 15.5.6EDV.1 The following is applicable to controls classied under 6.7.103BDV. 32 16 Environmental stress 35 17 Endurance .35 17.15 Single operation d
23、evices .36 17.16 Test for particular purpose controls 37 17.101 Type 2.P cycling test .41 18 Mechanical strength .43 18.101 Push-and-turn or pull-and-turn actuation 43 18.102 Parts containing liquid metal .44 19 Threaded parts and connections 45 20 Creepage distances, clearances and distances throug
24、h solid insulation .45 AUGUST 16, 2013 UL 60730-2-9 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 21 Fire hazard testing 45 22 Resistance to corrosion 45 23 Electromagnetic compatibility (EMC) requirements emission 45 23.101.1 Test condit
25、ions .45 23.101.2 Test procedure .46 24 Components .46 25 Normal operation .46 26 Electromagnetic compatibility (EMC) requirements immunity .46 27 Abnormal operation .46 27.101DV.1 Overvoltage .46 27.102DV.1 Thermal Cycling .46 27.103DV.1 Short Circuit 47 28 Guidance on the use of electronic disconn
26、ection .49 Annexes Annex H (normative) Requirements for electronic controls H.6 Classication 51 H.6.18 According to software class 51 H.7 Information 51 H.11 Constructional requirements 52 H.11.12 Controls using software 52 H.23 Electromagnetic compatibility (EMC) requirements emission 52 H.26 Elect
27、romagnetic compatibility (EMC) requirements immunity .52 H.26.5 Voltage dips and voltage interruptions in the power supply network 53 H.26.8 Surge immunity test 54 H.26.9 Electrical fast transient/burst immunity test 54 H.26.10 Ring wave test 54 H.26.12 Radio-frequency electromagnetic eld immunity .
28、55 H.26.13 Test of inuence of supply frequency variations .55 H.26.14 Power frequency magnetic eld immunity test 55 H.26.15 Evaluation of compliance .56 H.27 Abnormal operation .56 Annex J (normative) Requirements for controls using thermistors J.4 General notes on tests 57 J.7 Information 57 OCTOBE
29、R 13, 2010 UL 60730-2-9 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Annex AA (informative) Maximum manufacturing deviation and drift a, b Annex BB (informative) Time factor BB.0 Introduction 60 BB.2 Two-bath method .60 BB.3 Gradient met
30、hod 60 Annex CC (informative) Number of cycles CC.1 Number of cycles for independently mounted and in-line cord controls 64 CC.2 Minimum number of cycles for independently mounted and in-line cord controls (Canada and the USA) 64 Annex DD (normative) Controls for use in agricultural connement buildi
31、ngs DD.1 Object .65 DD.2 Denitions .65 DD.3 Test apparatus .65 DD.4 Severities 65 DD.5 Pre-conditioning 65 DD.6 Initial measurements 65 DD.7 Testing 65 DD.7.1 Moist carbon dioxide sulfur dioxide air mixture .66 DD.7.2 Moist hydrogen sulde air mixture 66 DD.7.3 Moist ammonia air mixture 66 DD.7.4 Ure
32、a water vapour .67 DD.7.5 Warm humid air 67 DD.7.6 Disinfectant germicide water mixture exposure .67 DD.7.7 Dust exposure .67 DD.8 Recovery 67 DD.9 Evaluation .67 DD.9.1 General .67 OCTOBER 13, 2010 UL 60730-2-9 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT
33、 PERMISSION FROM UL Annex EE (informative) Guide to the application of temperature sensing controls within the scope of IEC 60730-2-9 EE.1 General .69 EE.1.2 Overview 69 EE.2 Selection of temperature sensing controls within the scope of IEC 60730-2-9 69 EE.3 Classications common to temperature sensi
34、ng controls 70 EE.3.1 Nature of supply .70 EE.3.2 Type of load .70 EE.3.3 Types of temperature sensing controls according to their purpose 71 EE.3.4 Features of automatic action 72 EE.3.5 Control pollution situation .73 EE.3.6 Method of connection .74 EE.3.7 Ambient temperature limits of the switch
35、head .74 EE.3.8 Protection against electric shock 75 EE.3.9 Circuit disconnection or interruption 75 EE.3.10 Number of cycles of actuation (M) of each manual action 76 EE.3.11 Number of automatic cycles (A) of each automatic action 77 EE.3.12 Temperature limits of the mounting surface of the control
36、 78 EE.3.13 Value of proof tracking index (PTI) for the insulation material used 78 EE.3.14 Period of electrical stress across insulating parts supporting live parts and between live parts and earthed metal 78 EE.3.15 Construction 79 EE.3.16 Ageing requirements of the equipment in which the control
37、is intended to be used .79 EE.4 Specic types of temperature sensing control 79 EE.4.1 Thermostats .79 EE.4.2 Temperature limiter .81 EE.4.3 Thermal cut-out 84 EE.4.4 Single operation device .86 Manufacturing and Production Tests (normative) OCTOBER 13, 2010 UL 60730-2-9 6UL COPYRIGHTED MATERIAL NOT
38、AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 13, 2010 UL 60730-2-9 7 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface (UL) This UL Standard Automatic Electrical Controls Fo
39、r Household and Similar Use; Part 2: Particular Requirements for Temperature Sensing Controls, 60730-2-9, is to be used in conjunction with the third edition of UL 60730-1. The requirements for temperature sensing controls are contained in this part 2 Standard and UL 60730-1. Requirements of this pa
40、rt 2 Standard, where stated, amend the requirements of UL 60730-1. Where a particular subclause of UL 60730-1 is not mentioned in UL 60730-2-9, the UL 60730-1 subclause applies. The text, gures and tables of the IEC Standard for Automatic Electrical Controls For Household and Similar Use; Part 2: Pa
41、rticular Requirements for Temperature Sensing Controls, 60730-2-9, copyright June 2008 issued in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted material has been reproduced with permission from ANSI. ANSI should be contacted regard
42、ing the reproduction of any portion of the IEC material. The IEC Foreword and Introduction are not a part of the requirements of this Standard but are included for information purposes only. Copies of IEC Publication 60730-2-2 may be purchased from ANSI, 25 West 43rd Street, 4th Floor, New York, NY
43、10036, (212) 642-4900. Note Although the intended primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose. These materials are subject to copyright claim
44、s of IEC and UL. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of UL. All requests pertaining to the UL 60730-2-9 standard should be submitted to UL. UL effective date The effective date for UL 60730-2-9, thi
45、rd edition, is October 19, 2018. A UL effective date is one established by Underwriters Laboratories Inc. and is not part of the ANSI approved standard. AUGUST 16, 2013 UL 60730-2-9 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NATIONAL D
46、IFFERENCES National Differences from the text of International Electrotechnical Commission (IEC) Publication IEC 60730-2-9 are indicated by notations (differences) and are presented in bold text. There are ve types of National Differences as noted below. The difference type is noted on the rst line
47、of the National Difference in the standard. The standard may not include all types of these National Differences. D1 These are National Differences which are based on basic safety principles and requirements, elimination of which would compromise safety for consumers and users of products. D2 These
48、are national differences from IEC requirements based on existing safety practices. These requirements reect national safety practices, where empirical substantiation (for the IEC or national requirement) is not available or the text has not been included in the IEC standard. DC These are National Di
49、fferences based on the component standards and will not be deleted until a particular component standard is harmonized with the IEC component standard. DE These are National Differences based on editorial comments or corrections. DR These are National Differences based on the national regulatory requirements. Each national difference contains a description of what the national difference entails. Typically one of the following words is used to explain how t
