UNE 7 084 《砾石和沙石的表面湿度的确定》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN EN ISO 293-2005 Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293 2004) English version of DIN EN ISO 293《塑料 热塑性材料试样的压模铸造》.pdf

DIN EN ISO 294-1-2017 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1 General principles and moulding of multipurpose and bar test specimens (IS.pdf

DIN EN ISO 294-2-2006 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2 Small tensile bars (ISO 294-2 1996 + Amd 1 2004) English version of DIN EN.pdf

DIN EN ISO 294-3-2003 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3 Small plates (ISO 294-3 2002) German version EN ISO 294-3 2003《塑料 热塑性材料试样的.pdf

DIN EN ISO 294-4 Berichtigung 1-2011 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 Determination of moulding shrinkage (ISO 294-4 2001) German.pdf

DIN EN ISO 294-4-2003 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 Determination of moulding shrinkage (ISO 294-4 2001) German version EN ISO.pdf

DIN EN ISO 295-2004 Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295 2004) German version EN ISO 295 2004《塑料 热固性材料试样的压模塑法》.pdf

DIN EN ISO 3001-1999 Plastics - Epoxide compounds - Determination of epoxide equivalent (ISO 3001 1999) German version EN ISO 3001 1999《塑料 环氧化合物 环氧基当量的测定》.pdf

DIN EN ISO 3035-2012 Corrugated fibreboard - Determination of flat crush resistance (ISO 3035 2011) German version EN ISO 3035 2011《瓦楞纤维板 抗平压强度的测定(ISO 3035-2011) 德文版本EN ISO 3035-20.pdf