1、 INTERNATIONAL STANDARD IECCEINORME INTERNATIONALE60034-8Third editionTroisime dition2007-06Rotating electrical machines Part 8: Terminal markings and direction of rotation Machines lectriques tournantes Partie 8: Marques dextrmit et sens de rotation Reference number Numro de rfrence IEC/CEI 60034-8
2、2007 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permis
3、sion in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for
4、further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du
5、 Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, r
6、ue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC p
7、ublications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to sear
8、ch by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publica
9、tions released. Available on-line and also by email. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41
10、 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu techniq
11、ue des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des rech
12、erches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille
13、deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou conta
14、ctez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IECCEINORME INTERNATIONALE60034-8Third editionTroisime dition2007-06Rotating electrical machines Part 8: Terminal markings and direction of rotation Machines lectriques tournantes Partie 8: Marques dextrmi
15、t et sens de rotation V Commission Electrotechnique InternationaleInternational Electrotechnical Commission PRICE CODE CODE PRIX For price, see current cataloguePour prix, voir catalogue en vigueur 2 60034-8 IEC:2007 CONTENTS FOREWORD.5 INTRODUCTION.7 1 Scope.8 2 Normative references .8 3 Terms and
16、definitions .8 4 Symbols .10 4.1 General .10 4.2 DC and single-phase commutator machines 10 4.3 AC machines without commutators10 4.4 Auxiliary devices .11 5 Direction of rotation 11 6 Rules for terminal markings 11 6.1 General .11 6.2 Suffixes.12 6.3 Prefixes.13 6.4 Winding identification for categ
17、ories of machines 13 6.5 Synchronous machines .14 6.6 DC machines.14 6.7 Relation between terminal markings and direction of rotation 14 6.8 Terminal marking figures .15 7 Auxiliary terminal marking rules20 7.1 General .20 7.2 Marking .20 Annex A (normative) Connection diagrams for common applicatio
18、ns23 Figure 1 Single three-phase winding, three elements, open connection, six terminals .15 Figure 2 Single three-phase winding, delta connection, three terminals .16 Figure 3 Single three-phase winding, internal star connection with neutral conductor, four terminals16 Figure 4 Single three-phase w
19、inding, two elements per phase, open connection, twelve terminals16 Figure 5 Single three-phase winding, four elements per phase, open connection, twenty-four terminals 16 Figure 6 Single three-phase winding, two elements per phase with four tapping points per element, open connection, thirty-six te
20、rminals 17 Figure 7 Two separate three-phase windings with two independent functions, two elements per phase, open connection, twenty-four terminals 17 Figure 8 Two elements, internal connection, three terminals 17 Figure 9 Single three-phase winding, star connection, duplicate terminals for alterna
21、te connection, six terminals17 Figure 10 Single three-phase winding, star connection, parallel terminals for shared current, six terminals 18 60034-8 IEC:2007 3 Figure 11 Three-phase wound-rotor, star connections with neutral conductors, eight terminals.18 Figure 12 Main and auxiliary winding, two e
22、lements.18 Figure 13 Single-phase auxiliary winding, integrally connected capacitor, one element 18 Figure 14 Single-phase main winding, integrally connected thermal protector, one element 18 Figure 15 Six-phase winding, open connection, six elements .18 Figure 16 Armature winding, one element 19 Fi
23、gure 17 Commutating winding, one and two elements .19 Figure 18 Compensating winding, one and two elements .19 Figure 19 Series winding, one element, two tappings.19 Figure 20 Shunt excitation winding, one element .19 Figure 21 Separately excited excitation winding, one and two elements.19 Figure 22
24、 Direct-axis auxiliary winding, one element19 Figure 23 Quadrature-axis auxiliary winding, one element .19 Figure 24 Armature winding with commutating and compensating windings, one element 19 Figure 25 Single-phase, single voltage 20 Figure 26 Single-phase, dual voltage .20 Figure 27 Three-phase, s
25、ingle voltage .21 Figure 28 Three-phase, dual voltage21 Figure 29 Two-lead devices (except type R) 21 Figure 30 Two-lead devices of type R 21 Figure 31 Three-lead devices of type R22 Figure 32 Four-lead devices of type R .22 Figure 33 Switch connections 22 Figure A.1 Delta connection.23 Figure A.2 S
26、tar connection with or without neutral .23 Figure A.3 Dual voltage, six terminals (1:3)23 Figure A.4 Star-connected, dual voltage, nine terminals (1:2) 24 Figure A.5 Delta-connected, dual voltage, nine terminals (1:2).24 Figure A.6 Star-delta, single voltage, six terminals.24 Figure A.7 Star-delta,
27、dual voltage, twelve terminals (1:2) .25 Figure A.8 Part-winding, single voltage, six terminals 25 Figure A.9 Part-winding, dual voltage, nine terminals (1:2).26 Figure A.10 Variable-torque, six terminals .26 Figure A.11 Variable-torque, dual-voltage (1:3), nine terminals 27 Figure A.12 Constant-tor
28、que, six terminals 28 Figure A.13 Constant power, six terminals .28 Figure A.14 Variable-torque, six terminals .29 Figure A.15 Constant-torque, seven terminals29 Figure A.16 Constant-power, seven terminals 29 4 60034-8 IEC:2007 Figure A.17 Example of three-speed, constant torque motor using two sepa
29、rate windings, ten terminals .30 Figure A.18 Example of three-speed motor using three separate windings, ten terminals.30 Figure A.19 Example of four-speed, variable-torque motor using two separate windings, twelve terminals 31 Figure A.20 Split-phase or capacitor-start reversible motor 31 Figure A.
30、21 Reversible capacitor-start motor with four terminals with externally connected capacitor32 Figure A.22 Shunt motor or generator, four terminals.32 Figure A.23 Compound-motor or generator with compensating and commutating windings, six terminals32 Figure A.24 Series-wound motor, two terminals .33
31、60034-8 IEC:2007 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ROTATING ELECTRICAL MACHINES Part 8: Terminal markings and direction of rotation FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical com
32、mittees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technic
33、al Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmenta
34、l and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agre
35、ements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use
36、and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promot
37、e international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicat
38、ed in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to
39、 IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
40、 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9)
41、 Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60034-8 has been prepared by IEC technical committee 2: Rotating m
42、achinery. This third edition of IEC 60034-8 cancels and replaces the second edition published in 2002 and constitutes a technical revision. The main change with respect to the previous edition is listed below: changed terminal markings for d.c. machines in Clause A.4. 6 60034-8 IEC:2007 The text of
43、this standard is based on the following documents: FDIS Report on voting 2/1434/FDIS 2/1451/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directi
44、ves, Part 2. A list of all the parts of the IEC 60034 series, under the general title Rotating electrical machines, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site u
45、nder “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 60034-8 IEC:2007 7 INTRODUCTION The revision of this part of IEC 60034 provides worldwide uniformity in the electrica
46、l connections for rotating electrical machines and applies the recommendations of the basic safety publication IEC 60445 in specifying marking requirements. These standardized connections will then permit the safe interchange of electric machines with their control and protective devices using stand
47、ardized terminal markings. 8 60034-8 IEC:2007 ROTATING ELECTRICAL MACHINES Part 8: Terminal markings and direction of rotation 1 Scope This part of IEC 60034 applies to a.c. and d.c. machines and specifies a) rules for the identification of winding connection points; b) marking of winding terminals;
48、 c) direction of rotation; d) relationship between terminal markings and direction of rotation; e) terminal marking of auxiliary devices; f) connection diagrams of machines for common applications. Turbine-type synchronous machines are excluded from this standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60034-1, Rotating electrical m
