1、 IEC 62329-1 Edition 1.0 2005-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Heat shrinkable moulded shapes Part 1: Definitions and general requirements Profils thermortractables Partie 1: Dfinitions et exigences gnrales IEC 62329-1:2005-11(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 20
2、05 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Co
3、mmittee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf i
4、ndication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez d
5、es questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211
6、Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content o
7、f IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC I
8、nternational Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical
9、 committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedi
10、a - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Gl
11、ossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Serv
12、ice Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie
13、des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut
14、avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Rech
15、erche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - websto
16、re.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il
17、contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 55 000 entres terminologiques lectrotechniques
18、, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette
19、 publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62329-1 Edition 1.0 2005-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Heat shrinkable moulded shapes Part 1: Definitions and general requirements Profils thermortractables Partie 1: Dfinitions et exigences gnrales INTERNATIO
20、NAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 29.035.20 PRICE CODE CODE PRIX ISBN 978-2-8322-1598-2 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtai
21、ned this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 62329-1:2005 IEC 2005 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ HEAT SHRINKABLE MOULDED SHAPES Part 1: Definitions and general requirements FO
22、REWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the e
23、lectrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to
24、technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International
25、Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each tech
26、nical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publ
27、ications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their nat
28、ional and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to
29、be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Commit
30、tees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to
31、the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be he
32、ld responsible for identifying any or all such patent rights. This International Standard has been prepared by IEC technical committee 15: Standards on specifications for electrical insulating materials. This bilingual version (2014-05) corresponds to the English version, published in 2005-11. The t
33、ext of this standard is based on the following documents: FDIS Report on voting 15/233/FDIS 15/262/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. IEC
34、62329-1:2005 IEC 2005 3 The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirm
35、ed; withdrawn; replaced by a revised edition, or amended. 4 IEC 62329-1:2005 IEC 2005 INTRODUCTION This standard is one of a series which deals with heat shrinkable moulded shapes for electrical insulation purposes. The series will consist of three parts: Part 1: Definitions and general requirements
36、 Part 2: Methods of test Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance IEC 62329-1:2005 IEC 2005 5 HEAT SHRINKABLE MOULDED SHAPES Part 1: Definitions and general requirements 1 Scope This standard is applicable to heat shrinkable moulded
37、 shapes in a range of configurations and materials suitable for insulation, environmental sealing, mechanical protection and strain relief for connector/cable terminations and multi-way transitions. It specifies the design and dimensions, test methods, material requirements and compatibility perform
38、ance. The most commonly available shapes are as shown in Annex A. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performa
39、nce in that application and not based on this specification alone. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu
40、ment (including any amendments) applies. IEC 60050(212):1990, International Electrotechnical Vocabulary Chapter 212: Insulating solids, liquids and gases IEC 62329-2: Heat shrinkable moulded shapes Part 2: Methods of test 13 Terms and definitions For the purposes of this document, the terms and defi
41、nitions of the International Electrotechnical Vocabulary IEC 60050-212, Section 1 (Terms relating to electrical properties), apply as well as the following: 3.1 central value the middle result of an odd number of measurements or the mean of the two middle results of an even number of measurements wh
42、en arranged in order of magnitude 3.2 consignment all shapes of one size, type, grade and colour submitted for delivery at the same time _ 1To be published 6 IEC 62329-1:2005 IEC 2005 4 Specimens 4.1 Moulded shape material specimens Unless otherwise specified, specimens shall be cut from standard te
43、st sheets (2 0,15) mm thick, prepared from the same heat shrinkable material as is used to manufacture the heat shrinkable moulded shapes. The dimensions of the sheet shall be sufficient to enable any of the relevant tests in Part 3 to be performed. NOTE A suitable size has been found to be 150 mm x
44、 150 mm. 4.2 Moulded shape compatibility specimens Specimens for test of compatibility shall consist of a moulded shape, cable sheathed with heat shrink sleeves and metal adaptor. Also, adhesives when supplied as a separate component. The specimen configuration and sizes shall be as specified in Par
45、t 2. 5 Classification Moulded shapes are classified by style configuration as shown in Annex A. 6 Ordering When ordering heat shrinkable moulded shapes, purchasers shall include the description as detailed under designation given in the Part 3 sheets. 7 Dimensions Preferred types and sizes are given
46、 in Part 3 but may be subject to agreement between purchaser and supplier. 8 Colour The standard colour is black. Non standard colours may be subject to agreement between customer and supplier. 9 Finish The heat shrinkable moulded shapes shall be uniform in appearance, and free from internal and ext
47、ernal irregularities. There shall be no defects capable of affecting the characteristics specified in Part 3. 10 Packaging Heat shrinkable moulded shapes shall be supplied in a way which ensures adequate protection during transport, handling and storage. IEC 62329-1:2005 IEC 2005 7 11 Labelling Each
48、 unit pack shall have the designation information clearly and indelibly marked on it as given in the IEC 62329-3 sheets and the following information unless otherwise agreed between purchaser and supplier. a) Manufacturers or suppliers name or identification mark b) Batch number c) Use by date d) Qu
49、antity 12 Qualification approval requirements 12.1 When agreed between purchaser and supplier, the supplier shall provide third party certification by an approved National or International Approval Agency. 12.2 Where agreed between the purchaser and supplier, the supplier shall provide details of material composition, agreed techniques and evidence to the satisfaction of the approving Authority that the heat shrin
