1、 IEEE Standard Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and Cable Corrigendum 1 Sponsored by the Insulated Conductors Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy Society IEEE Std 1210-2004/Cor 1-2014 (Corrigendum to IEEE Std 1210-20
2、04) IEEE Std 1210-2004/Cor 1-2014 (Corrigendum to IEEE Std 1210-2004) IEEE Standard Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and Cable Corrigendum 1 Sponsor Insulated Conductors Committee of the IEEE Power and Energy Society Approved 27 March 2014 IEEE-SA Standards B
3、oard Abstract: Criteria and test methods for determining the compatibility of cable-pulling lubricants (compounds) with cable jacket or other exterior cable covering are described in this standard. Cable-pulling lubricants are used to lower the friction on cable as it is pulled into conduit, duct, o
4、r directionally bored holes. Compatibility is important because lubricants should not negatively interact with the cables they lubricate. Compatibility of lubricants with a variety of common cable coverings is considered. This Corrigendum is to replace equations in 4.3 and 5.3 and to correct the leg
5、end in Table 4 in 4.5. Keywords: cable, cable covering, cable jacket, cable pulling, compatibility, compound, dielectric withstand, IEEE 1210, immersion testing, lubricants, physical properties, volume resistance measurement, wire The Institute of Electrical and Electronics Engineers, Inc. 3 Park Av
6、enue, New York, NY 10016-5997, USA Copyright 2014 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 4 April 2014. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement;
7、 and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existen
8、ce of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change broug
9、ht about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform a
10、ny duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining t
11、he appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEV
12、ER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS F
13、ORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or
14、oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, sem
15、inars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents
16、are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with approp
17、riate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committ
18、ees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome t
19、o join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance
20、with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urg
21、e action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both
22、public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE
23、does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. T
24、o arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clear
25、ance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE docum
26、ent at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is
27、 reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whe
28、ther it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE
29、-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the
30、possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applican
31、t has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rig
32、hts without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not re
33、sponsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in
34、any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE St
35、andards Association. Copyright 2014 IEEE. All rights reserved. viParticipants At the time this IEEE standard was completed, the A8W (Compatibility of Cable Jackets and Pulling Lubricants) Working Group had the following membership: Joseph W. McAullife, Chair Don Smith, Vice Chair Ariel Conde David E
36、lliott Sean Foley Robert DeMain Juan Gutierrez, Jr. John Hans Richard Harp Jeffrey Helzer Jim Hunt Paul Jakob Albert Kong Leo Martinez T. J. Quinn Brian Sides Albert Spear The following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disap
37、proval, or abstention. Saleman Alibhay Earle Bascom III William Bloethe Kenneth Bow Chris Brooks Thomas Campbell John Cancelosi David Crotty Gary Donner Steven Graham Randall Groves Ajit Gwal Richard Harp Jeffrey Helzer Lee Herron Lauri Hiivala Werner Hoelzl Dennis Johnson A. Jones Albert Kong Jim K
38、ulchisky Chung-Yiu Lam Michael Lauxman Arturo Maldonado William McBride John Merando Michael Newman Lorraine Padden Robert Resuali Michael Roberts Stephen Sandberg Bartien Sayogo Michael Smalley Jerry Smith Gregory Stano Gary Stoedter Peter Tirinzoni John Vergis Daniel Ward Yingli Wen Kenneth White
39、Dawn Zhao When the IEEE-SA Standards Board approved this standard on 27 March 2014, it had the following membership: John Kulick, Chair Jon Walter Rosdahl, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Peter Balma Farooq Bari Ted Burse Clint Chaplin Stephen Dukes Jean-
40、Philippe Faure Gary Hoffman Michael Janezic Jeffrey Katz Joseph L. Koepfinger* David J. Law Hung Ling Oleg Logvinov Ted Olsen Glenn Parsons Ron Petersen Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Don Wright Yu Yuan *Member Emeritus Also included are the following nonvoting IEEE-SA S
41、tandards Board liaisons: Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Patrick Gibbons IEEE Standards Program Manager, Document Development Malia Zaman IEEE Standards Program Manager, Technical Program Development Copyright 2014 IEEE. All rights reserved. vii Copyright 20
42、14 IEEE. All rights reserved. viiiIntroduction This introduction is not part of IEEE Std 1210-2004/Cor 1-2014, IEEE Standard for Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and CableCorrigendu
43、m 1. This Corrigendum is to replace equations in 4.3 and 5.3 and to correct the legend in Table 4 in 4.5 of IEEE Std 1210-2004 Standard Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and Cable. Contents 4. Electrical property effects 2 5. Testing and test methods . 2 Copyr
44、ight 2014 IEEE. All rights reserved. ix Copyright 2014 IEEE. All rights reserved. 1IEEE Standard Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and Cable Corrigendum 1 IMPORTANT NOTICE: IEEE Standards documents are not intended to ensure safety, health, or environmental pr
45、otection, or ensure against interference with or from other devices or networks. Implementers of IEEE Standards documents are responsible for determining and complying with all appropriate safety, security, environmental, health, and interference protection practices and all applicable laws and regu
46、lations. This IEEE document is made available for use subject to important notices and legal disclaimers. These notices and disclaimers appear in all publications containing this document and may be found under the heading “Important Notice” or “Important Notices and Disclaimers Concerning IEEE Docu
47、ments.” They can also be obtained on request from IEEE or viewed at http:/standards.ieee.org/IPR/disclaimers.html. NOTEThe editing instructions contained in this corrigendum define how to merge the material contained therein into the existing base standard and its amendments to form the comprehensiv
48、e standard. The editing instructions are shown in bold italic. Four editing instructions are used: change, delete, insert, and replace. Change is used to make corrections in existing text or tables. The editing instruction specifies the location of the change and describes what is being changed by u
49、sing strikethrough (to remove old material) and underscore (to add new material). Delete removes existing material. Insert adds new material without disturbing the existing material. Insertions may require renumbering. If so, renumbering instructions are given in the editing instruction. Replace is used to make changes in figures or equations by removing the existing figure or equation and replacing it with a new one. Editing instructions, change markings, and this NOTE will not be carried over into future editions because the changes will be incorporated into the base
