1、 Reference number ISO 29467:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 29467 First edition 2008-11-01 Thermal insulating products for building applications Determination of squareness Produits isolants thermiques destins aux applications du btiment Dtermination de lquerrage ISO 29467:2008(E) PDF dis
2、claimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties
3、 accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to
4、the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PRO
5、TECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs
6、member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedISO 29467:2008(E) ISO 2008 All rights reserved iii Contents
7、 Page Foreword iv Introduction v 1 Scope . 1 2 Terms and definitions. 1 3 Principle. 2 4 Apparatus 2 5 Test specimens . 3 6 Procedure 3 7 Calculation and expression of results 4 8 Accuracy of measurement. 5 9 Test report . 5 ISO 29467:2008(E) iv ISO 2008 All rights reservedForeword ISO (the Internat
8、ional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has bee
9、n established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stand
10、ardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for
11、 voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all
12、 such patent rights. ISO 29467 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 1, Test and measurement methods. ISO 29467:2008(E) ISO 2008 All rights reserved v Introduction This International Standard comprises the origina
13、l EN 824:1994 prepared by Technical Committee CEN/TC 88, Thermal insulating materials and products, which has been amended by ISO/TC 163/SC 1 with reference to conditioning and testing conditions in tropical countries. This International Standard is one of a series of documents specifying test metho
14、ds, based on existing European Standards, that are being adopted by ISO. This “package” of standards includes the following group of interrelated documents. International Standard Respective EN standard ISO 29465, Thermal insulating products for building applications Determination of length and widt
15、h EN 822 ISO 29466, Thermal insulating products for building applications Determination of thickness EN 823 ISO 29467, Thermal insulating products for building applications Determination of squareness EN 824 ISO 29468, Thermal insulating products for building applications Determination of flatness E
16、N 825 ISO 29469, Thermal insulating products for building applications Determination of compression behaviour EN 826 ISO 29470, Thermal insulating products for building applications Determination of the apparent density EN 1602 ISO 29471, Thermal insulating products for building applications Determi
17、nation of dimensional stability under constant normal laboratory conditions (23C/50 % relative humidity) EN 1603 ISO 29472, Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 1604 ISO 29764, Thermal insu
18、lating products for building applications Determination of deformation under specified compressive load and temperature conditions EN 1605 ISO 29765, Thermal insulating products for building applications Determination of tensile strength perpendicular to faces EN 1607 ISO 29766, Thermal insulating p
19、roducts for building applications Determination of tensile strength parallel to faces EN 1608 ISO 29767, Thermal insulating products for building applications Determination of short- term water absorption by partial immersion EN 1609 ISO 29768, Thermal insulating products for building applications D
20、etermination of linear dimensions of test specimens EN 12085 ISO 29769, Thermal insulating products for building applications Determination of behaviour under point load EN 12430 ISO 29467:2008(E) vi ISO 2008 All rights reservedISO 29770, Thermal insulating products for building applications Determi
21、nation of thickness for floating-floor insulating products EN 12431 ISO 29771, Thermal insulating materials for building applications Determination of organic content EN 13820 ISO 29803, Thermal insulation products for building applications Determination of the resistance to impact of external therm
22、al insulation composite systems (ETICS) EN 13497 ISO 29804, Thermal insulation products for building applications Determination of the tensile bond strength of the adhesive and of the base coat to the thermal insulation material EN 13494 ISO 29805, Thermal insulation products for building applicatio
23、ns Determination of the mechanical properties of glass fibre meshes EN 13496 INTERNATIONAL STANDARD ISO 29467:2008(E) ISO 2008 All rights reserved 1 Thermal insulating products for building applications Determination of squareness 1 Scope This International Standard specifies the equipment and proce
24、dure for determining the deviation from squareness for length, width and/or thickness of full-size products. It is applicable to thermal insulating products. The method is normally applicable to products with straight edges. For products of other shape, e.g. profiled edges, the method can be adapted
25、 accordingly. 2 Terms and definitions For the purposes of this document, the following term and definition apply. 2.1 deviation from squareness distance from one limb of a perfect square (see Figures 1, 2 and 3) to the edge of the product at a given distance from a corner Figure 1 Example of the mea
26、surement of the length- and width-edge squareness and of thickness-edge squareness ISO 29467:2008(E) 2 ISO 2008 All rights reservedKey b length or width of the product depending on which corner is being controlled a bdeviation from squareness of the length or width c length of inner side of the squa
27、re Figure 2 Example of the measurement of length- and width-edge squareness Key d thickness of the product a ddeviation from squareness Figure 3 Example of the measurement of the thickness-edge squareness 3 Principle Apply a metal square to the product edges and measure the deviation between one lim
28、b of the metal square and the products edge (see Figure 1). 4 Apparatus 4.1 Flat surface. 4.2 Metal rule or metal tape, graduated in millimetres and permitting reading to 0,5 mm. 4.3 Metal square, with limbs at least 500 mm long with a deviation from squareness of not more than 0,1 mm when measured
29、at 500 mm from the corner. Any test equipment that provides the same result with at least the same accuracy may be used. ISO 29467:2008(E) ISO 2008 All rights reserved 3 5 Test specimens 5.1 Dimensions of test specimens The test specimens shall be the full-size product. 5.2 Number of test specimens
30、The number of test specimens shall be as specified in the relevant product standard. In the absence of a product standard, the number of test specimens may be agreed between parties. 5.3 Conditioning of test specimens The test specimens should be stored for at least 6 h at (23 5) C. In case of dispu
31、te, they shall be stored at (23 2) C and (50 5) % relative humidity for the time specified in the relevant product standard. In tropical countries, different conditioning and testing conditions can be relevant. In this case, the conditions shall be 27 C and 65 % RH and be stated clearly in the test
32、report. 6 Procedure 6.1 Determination of the squareness of the length and width edges 6.1.1 Test conditions The test should be carried out at (23 5) C. In case of dispute, it shall be carried out at (23 2) C and (50 5) % relative humidity. In tropical countries, different conditioning and testing co
33、nditions can be relevant. In this case, the conditions shall be 27 C and 65 % RH and be stated clearly in the test report. 6.1.2 Test procedure Lay the test specimen on a flat surface and measure the deviation from squareness of length and width as follows. a) Place the metal square along one of the
34、 sides of the test specimen with the right angle of the square aligned against the adjoining edge as shown in Figure 2. b) Measure the distance, a b , between the edge of the test specimen and the edge of the metal square, at a distance, c, from the corner, to the nearest 0,5 mm, where 1) for the te
35、st specimens with a side of less than 500 mm, c is the maximum width or length of the specimen, 2) for the test specimens with a side equal to or greater than 500 mm, c is the length of the inner side of the square (see Figure 2). c) Repeat for all corners of the test specimen having angles smaller
36、than or equal to 90. d) If there is any significant deviation from linearity of the edges in the length or the width, this shall be reported as the maximum deviation from linearity, a max , expressed in millimetres (see Figure 4). ISO 29467:2008(E) 4 ISO 2008 All rights reservedFigure 4 Example of t
37、he measurement of the deviation from linearity of an edge 6.2 Determination of the squareness of the thickness edge 6.2.1 Test conditions The test should be carried out at (23 5) C. In case of dispute it shall be carried out at (23 2) C and (50 5) % relative humidity. 6.2.2 Test procedure Lay the te
38、st specimen on a flat surface and measure the deviation from squareness of the thickness as follows. a) Place the metal square on the flat surface against one edge of the test specimen as shown in Figure 3. b) Measure the distance, a d , to the nearest 0,5 mm between the edge of the test specimen an
39、d the edge of the square at the point of the greatest deviation along the side. c) Repeat for all sides. d) Turn the test specimen over and repeat steps a) to c). e) Report the largest figure as the deviation from squareness of the thickness edge. 7 Calculation and expression of results 7.1 Calculat
40、ion of the deviation from the squareness of the length and width edges Calculate deviation from squareness, S b , using Equation (1): b b a S c = (1) where a bis the measured value, expressed in millimetres; c is the measured value, expressed in millimetres. Express the deviation from squareness, S
41、b , in millimetres per metre and round to the nearest millimetre per metre. ISO 29467:2008(E) ISO 2008 All rights reserved 5 7.2 Calculation of the deviation from squareness of the thickness edge Calculate deviation from squareness, S d , using Equation (2): S d= a d (2) where a dis the maximum meas
42、ured value, expressed in millimetres. Round the deviation, S d , to the nearest millimetre and report the thickness of the test specimen. 8 Accuracy of measurement NOTE It has not been possible to include a statement of the accuracy of the method in this edition of this International Standard, but i
43、t is intended to include such a statement when this International Standard is next revised. 9 Test report The test report shall include the following information: a) reference to this International Standard; b) product identification: 1) product name, factory, manufacturer or supplier, 2) production
44、 code number, 3) type of products, 4) packaging, 5) the form in which the product arrived at the laboratory, 6) other information as appropriate, e.g. nominal thickness, nominal density; c) test procedure: 1) pre-test history and sampling, e.g. from where and by whom, 2) conditioning, 3) any deviati
45、on from Clauses 5 and 6, 4) conditioning and testing conditions in tropical countries, if applicable, 5) date of testing, 6) general information relating to the test, 7) events that can have affected the results; NOTE It is expected that information about the apparatus and identity of the technician
46、 be available in the laboratory, but it is not necessary that it be recorded in the report. d) results: all individual values and the maximum value for deviation from squareness, expressed in millimetres per metre for the length and width; the deviation from squareness, expressed in millimetres for the thickness; and any deviation from linearity. See Figures 2 and 3. ISO 29467:2008(E) ICS 91.100.60 Price based on 5 pages ISO 2008 All rights reserved
