1、 Reference number ISO 5019-6:2005(E) ISO 2005INTERNATIONAL STANDARD ISO 5019-6 Second edition 2005-10-01 Refractory bricks Dimensions Part 6: Basic bricks for oxygen steel-making converters Briques rfractaires Dimensions Partie 6: Briques basiques pour convertisseurs oxygne ISO 5019-6:2005(E) PDF di
2、sclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, partie
3、s accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to
4、 the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All
5、 rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country o
6、f the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reservedISO 5019-6:2005(E) ISO 2005 All rights reserved iii Foreword ISO (the International Org
7、anization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establi
8、shed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardizatio
9、n. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
10、Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such pat
11、ent rights. ISO 5019-6 was prepared by Technical Committee ISO/TC 33, Refractories. This second edition cancels and replaces the first edition (ISO 5019-6:1984), of which Table 1 has been extended to include sizes from 850 mm to 1 000 mm, in 50 mm increments, and from 1 000 mm to 1 200 mm, in 100 mm
12、 increments, maintaining the existing tapers. ISO 5019 consists of the following parts, under the general title Refractory bricks Dimensions: Part 1: Rectangular bricks Part 2: Arch bricks Part 3: Rectangular checker bricks for regenerative furnaces Part 4: Dome bricks for electric arc furnace roofs
13、 Part 5: Skewbacks Part 6: Basic bricks for oxygen steel-making converters ISO 5019-6:2005(E) iv ISO 2005 All rights reservedIntroduction This International Standard is intended to provide standardized sizes of bricks from which to construct the working/hot-face lining for basic oxygen steel-making
14、converters. It provides for 18 thicknesses of lining, ranging from a minimum of 250 mm to a maximum of 1 200 mm. For each lining thickness, there is a rectangular brick (i.e. a brick with zero taper) and bricks with either four rates of taper for the five smallest thicknesses, or five or six rates o
15、f taper for the remaining thicknesses. All the bricks have a constant median dimension of 150 mm. The course height is uniformly 100 mm. INTERNATIONAL STANDARD ISO 5019-6:2005(E) ISO 2005 All rights reserved 1 Refractory bricks Dimensions Part 6: Basic bricks for oxygen steel-making converters 1 Sco
16、pe This part of ISO 5019 specifies the dimensions of basic refractory bricks for use in oxygen steel-making converters. The calculated volume of each size of brick is shown, for information, in Table 1, and also the internal diameter of lining for which each size is suitable, if used alone. These di
17、ameters have been calculated with no allowance for joint thickness. 2 Dimensions The dimensions of basic bricks for use in oxygen steel-making converters shall be as shown in Table 1. The symbols designating the dimensions in Table 1 are shown in Figure 1. NOTE These symbols do not necessarily apply
18、 to tables and figures in other International Standards. 3 Brick designations Each brick size has a conventional designation, as shown in the first column of Table 1. Each designation consists of two groups of digits separated by a solidus (slash). The group of two digits before the solidus shows th
19、e brick length (or lining thickness), in centimetres. It corresponds to A/10. The group after the solidus shows the difference, C D, between the cold-face and hot-face dimensions in millimetres (i.e. the rate of taper). In the case of a rectangular brick, the second group is a single zero. 4 Toleran
20、ces Tolerances on the dimensions specified in Table 1 shall be the subject of agreement between the purchaser and the supplier. ISO 5019-6:2005(E) 2 ISO 2005 All rights reservedFigure 1 Brick for oxygen steel-making converters Table 1 Dimensions of basic bricks for oxygen steel-making converters Dim
21、ensions mm Internal diameter Volume Designation A B C/D m dm 325/60 180/120 1,000 25/30 165/135 2,250 25/16 158/142 4,438 25/8 154/146 9,125 25/0 250 100 150/150 3,75 30/70 185/115 0,986 30/40 170/130 1,950 30/20 160/140 4,200 30/8 154/146 10,950 30/0 300 100 150/150 4,50 35/80 190/110 0,963 35/40 1
22、70/130 2,275 35/20 160/140 4,900 35/8 154/146 12,775 35/0 350 100 150/150 5,25 ISO 5019-6:2005(E) ISO 2005 All rights reserved 3 Table 1 (continued) Dimensions mm Internal diameter Volume Designation A B C/D m dm 340/80 190/110 1,100 40/40 170/130 2,600 40/20 160/140 5,600 40/8 154/146 14,600 40/0 4
23、00 100 150/150 6,00 45/90 195/105 1,050 45/40 170/130 2,925 45/20 160/140 6,300 45/8 154/146 16,425 45/0 450 100 150/150 6,75 50/100 200/100 1,000 50/60 180/120 2,000 50/36 168/132 3,667 50/20 160/140 7,000 50/8 154/146 18,250 50/0 500 100 150/150 7,50 55/110 205/95 0,950 55/80 190/110 1,513 55/60 1
24、80/120 2,200 55/36 168/132 4,033 55/20 160/140 7,700 55/8 154/146 20,075 55/0 550 100 150/150 8,25 60/120 210/90 0,900 60/80 190/110 1,650 60/60 180/120 2,400 60/36 168/132 4,400 60/20 160/140 8,400 60/8 154/146 21,900 60/0 600 100 150/150 9,00 65/120 210/90 0,975 65/80 190/110 1,788 65/60 180/120 2
25、,600 65/36 168/132 4,767 65/20 160/140 9,100 65/8 154/146 23,725 65/0 650 100 150/150 9,75 ISO 5019-6:2005(E) 4 ISO 2005 All rights reservedTable 1 (continued) Dimensions mm Internal diameter Volume Designation A B C/D m dm 370/120 210/90 1,050 70/80 190/110 1,925 70/60 180/120 2,800 70/36 168/132 5
26、,133 70/20 160/140 9,800 70/8 154/146 25,550 70/0 700 100 150/150 10,50 75/120 210/90 1,125 75/80 190/110 2,063 75/60 180/120 3,000 75/36 168/132 5,500 75/20 160/140 10,500 75/8 154/146 27,375 75/0 750 100 150/150 11,25 80/120 210/90 1,200 80/80 190/110 2,200 80/60 180/120 3,200 80/36 168/132 5,867
27、80/20 160/140 11,200 80/8 154/146 29,200 80/0 800 100 150/150 12,00 85/120 210/90 1,275 85/80 190/110 2,338 85/60 180/120 3,400 85/36 168/132 6,233 85/20 160/140 11,900 85/8 154/146 31,025 85/0 850 100 150/150 12,75 90/120 210/90 1,350 90/80 190/110 2,475 90/60 180/120 3,600 90/36 168/132 6,600 90/2
28、0 160/140 12,600 90/8 154/146 32,850 90/0 900 100 150/150 13,50 ISO 5019-6:2005(E) ISO 2005 All rights reserved 5 Table 1 (continued) Dimensions mm Internal diameter Volume Designation A B C/D m dm 395/120 210/90 1,425 95/80 190/110 2,613 95/60 180/120 3,800 95/36 168/132 6,967 95/20 160/140 13,300
29、95/8 154/146 34,675 95/0 950 100 150/150 14,25 100/120 210/90 1,500 100/80 190/110 2,750 100/60 180/120 4,000 100/36 168/132 7,333 100/20 160/140 14,000 100/8 154/146 36,500 100/0 1000 100 150/150 15,00 110/120 210/90 1,650 110/80 190/110 3,025 110/60 180/120 4,400 110/36 168/132 8,067 110/20 160/140 15,400 110/8 154/146 40,150 110/0 1100 100 150/150 16,50 120/120 210/90 1,800 120/80 190/110 3,300 120/60 180/120 4,800 120/36 168/132 8,800 120/20 160/140 16,800 120/8 154/146 43,800 120/0 1200 100 150/150 18,00 ISO 5019-6:2005(E) ICS 81.080 Price based on 5 pages ISO 2005 All rights reserved
