1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 603-18:2013 Bonded abrasive products Dimensions Part 18: Grinding wheels for flat glass edge grinding machinesBS ISO 603-18:2013 BRITISH STANDARD National foreword This
2、 British Standard is the UK implementation of ISO 603-18:2013. The UK participation in its preparation was entrusted to Technical Committee MTE/13, Grinding wheels, abrasive tools, paper and cloths, and powders. A list of organizations represented on this committee can be obtained on request to its
3、secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 72516 6 ICS 25.100.70 Compliance with a British Standa
4、rd cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013. Amendments issued since publication Date Text affectedBS ISO 603-18:2013 ISO 2013 Bonded abrasive products Dimensions Part 18:
5、Grinding wheels for flat glass edge grinding machines Produits abrasifs agglomrs Dimensions Partie 18: Meules pour machines meuler les bords de verre plat INTERNATIONAL STANDARD ISO 603-18 First edition 2013-01-15 Reference number ISO 603-18:2013(E)BS ISO 603-18:2013ISO 603-18:2013(E)ii ISO 2013 All
6、 rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO
7、 at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 603-18:2013ISO 603-18:2013(E) ISO 2013 All rights rese
8、rved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 Requirements 1 3.1 Shapes and dimensions . 1 3.2 Designation 6 3.3 Specifications 6BS ISO 603-18:2013ISO 603-18:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national st
9、andards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International o
10、rganizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules giv
11、en in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least
12、75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 603-18 was prepared by Technical Committee ISO/TC 29, S
13、mall tools, Subcommittee SC 5, Grinding wheels and abrasives. ISO 603 consists of the following parts, under the general title Bonded abrasive products Dimensions: Part 1: Grinding wheels for external cylindrical grinding between centres Part 2: Grinding wheels for centreless external cylindrical gr
14、inding Part 3: Grinding wheels for internal cylindrical grinding Part 4: Grinding wheels for surface grinding/peripheral grinding Part 5: Grinding wheels for surface grinding/face grinding Part 6: Grinding wheels for tool and tool room grinding Part 7: Grinding wheels for manually guided grinding Pa
15、rt 8: Grinding wheels for deburring and fettling/snagging Part 9: Grinding wheels for high-pressure grinding Part 10: Stones for honing and superfinishings Part 11: Hand finishing sticks Part 12: Grinding wheels for deburring and fettling on a straight grinder Part 13: Grinding wheels for deburring
16、and fettling on a vertical grinder Part 14: Grinding wheels for deburring and fettling/snagging on an angle grinder Part 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines Part 16: Grinding wheels for cutting-off on hand held power tools Part 17: Mounted wheels Part 18:
17、 Grinding wheels for flat glass edge grinding machinesiv ISO 2013 All rights reservedBS ISO 603-18:2013INTERNATIONAL ST ANDARD ISO 603-18:2013(E) Bonded abrasive products Dimensions Part 18: Grinding wheels for flat glass edge grinding machines 1 Scope This part of ISO 603 specifies the shapes, dime
18、nsions and limit deviations, in millimetres, of grinding wheels for flat glass edge grinding machines. This type of bonded abrasive wheel is intended to be used on stationary machines where the position of the grinding wheel is fixed and the workpiece is guided by hand or guided mechanically, or on
19、a stationary machine where the grinding wheel is guided mechanically and the workpiece is fixed. The common maximum operating speed, v s , for this type of bonded abrasive product is v s 50 m/s 2 Normative references The following documents, in whole or in part, are normatively referenced in this do
20、cument and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 525, Bonded abrasive products General requirements ISO 6103, Bonded abrasive products
21、Static balancing of grinding wheels Testing ISO 13942, Bonded abrasive products Limit deviations and run-out tolerances 3 Requirements 3.1 Shapes and dimensions 3.1.1 Straight wheel, type 1 See Figure 1 and Table 1. Figure 1 Straight wheel, type 1 ISO 2013 All rights reserved 1BS ISO 603-18:2013ISO
22、603-18:2013(E) Table 1 Straight wheels, type 1 Dimensions in millimetres D T H 100 10 22,00 100 15 22,00 100 20 22,00 100 25 22,00 100 30 22,00 120 10 22,00 120 15 22,00 120 20 22,00 120 25 22,00 120 30 22,00 150 15 22,00 150 20 22,00 150 25 22,00 150 30 22,00 200 20 60,00 200 25 60,00 200 30 60,00
23、200 15 90,00 200 20 90,00 200 25 90,00 200 30 90,00 200 40 90,00 250 20 50,00 250 25 50,00 250 30 50,00 3.1.2 Straight cup wheel, type 6 See Figure 2 and Table 2. Figure 2 Straight cup wheel, type 62 ISO 2013 All rights reservedBS ISO 603-18:2013ISO 603-18:2013(E) Table 2 Straight cup wheels, type 6
24、 Dimensions in millimetres D T H W E 100 30 50,00 20 7 100 35 50,00 20 7 100 40 11,00 20 8 100 40 50,00 20 7 100 45 11,00 20 8 100 45 50,00 20 8 125 35 22,00 20 10 130 35 22,00 22,5 10 130 35 50,00 22,5 10 130 35 70,00 22,5 10 130 39 11,00 22,5 10 130 40 50,00 22,5 10 150 30 50,00 22,5 12 150 30 70,
25、00 22,5 12 150 35 25,00 22,5 12 150 35 50,00 22,5 12 150 35 70,00 22,5 12 150 40 22,00 22,5 12 150 40 25,00 22,5 12 150 40 50,00 22,5 12 150 40 68,00 22,5 12 150 40 70,00 22,5 12 170 40 68,00 22,5 12 3.1.3 Disc wheel, cemented, type 35 See Figure 3 and Table 3. Figure 3 Disc wheel, cemented, type 35
26、 ISO 2013 All rights reserved 3BS ISO 603-18:2013ISO 603-18:2013(E) Table 3 Disc wheels, cemented, type 35 Dimensions in millimetres D T H 100 25 50,00 200 40 120,00 3.1.4 Straight wheel, type 1 with profile See Figure 4 and Table 4. NOTE This is a special profile, not defined in ISO 525. Figure 4 S
27、traight wheel, type 1 with profile4 ISO 2013 All rights reservedBS ISO 603-18:2013ISO 603-18:2013(E) Table 4 Straight wheels, type 1 with profile Dimensions in millimetres D T H Profile angle 140 4 22,00 12 140 5 22,00 12 140 6 22,00 12 140 8 22,00 12 140 10 22,00 12 150 4 22,00 12 150 5 22,00 12 15
28、0 6 22,00 12 150 8 22,00 12 150 10 22,00 12 150 4 60,00 12 150 5 60,00 12 150 6 60,00 12 150 8 60,00 12 150 10 60,00 12 160 4 90,00 12 160 5 90,00 12 160 6 90,00 12 160 8 90,00 12 160 10 90,00 12 200 6 60,00 12 200 8 60,00 12 200 10 60,00 12 200 6 90,00 12 200 8 90,00 12 200 10 90,00 12 220 6 60,00
29、12 220 8 60,00 12 220 10 60,00 12 NOTE Table 4 describes a special profile, which is not defined in ISO 525. ISO 2013 All rights reserved 5BS ISO 603-18:2013ISO 603-18:2013(E) 3.2 Designation A complete designation of a bonded abrasive product in accordance with this part of ISO 603 shall consist of
30、 the following information: a) designation of the bonded abrasive, grinding wheel for flat glass edge grinding machine; b) reference of this part of ISO 603, i.e. ISO 603-18; c) shape; d) type; e) dimensions D, T, H, W, E; f) . EXAMPLE A grinding wheel for flat glass edge grinding machine, Type 1, d
31、iameter D = 200 mm, thickness T = 20 mm, bore H = 90,00 mm, nature of abrasive AA, grit size 120, grade of hardness B, structure 5, bond type R and a maximum operating speed of 32 m/s is designated as follows: Grinding wheel for flat glass edge grinding machines ISO 603-18, 1 - 200 20 90 - AA120 B5R
32、 - 32 m/s 3.3 Specifications 3.3.1 Tolerances Limit deviations and run-out tolerances shall be in accordance with ISO 13942. 3.3.2 Unbalance Unbalance shall be in accordance with ISO 6103. 3.3.3 Marking Marking of grinding wheels for flat glass edge grinding machines shall be in accordance with ISO
33、525.6 ISO 2013 All rights reservedBS ISO 603-18:2013BS ISO 603-18:2013ISO 603-18:2013(E) ISO 2013 All rights reserved ICS 25.100.70 Price based on 6 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publ
34、ications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited. British Standards Institution (BSI) raising standards
35、worldwide BSI 389 Chiswick High Road London W4 4AL UK Te l + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 Fax +44 (0)20 8996 7001 Revisions British Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or
36、editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the in
37、side front cover. S i m i l a r y f o r P A S s , p l e a s e n o t i f y B S I C u s t o m e r S e r v i c e s . Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscriber
38、s automatically receive the latest editions of British Standards and PASs. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 7 6 6 9 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 Email: Buying standards Yo u m a y b u y P D F a n d h a rd c o p y v e r s i o n s o f s t a n d a rd s d i re c t l y u s i n g a credit card f
39、rom the BSI Shop on the website In addition all orders for BSI, international and foreign standards publications can be addressed to BSI Customer Services. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 Email: In response to orders for international standards, BSI w
40、ill supply the British Standard implementation of the relevant international standard, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Knowledge Centre. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 4
41、F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 5 Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0
42、0 2 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at Further information about British Standards is available on the BSI website at www.bsi- Copyright All the data, software and documentati
43、on set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication a
44、nd use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the f
45、ree use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 7 0 Email:
