1、BSI Standards Publication BS ISO 6361-3:2014 Wrought aluminium and aluminium alloys Sheets, strips and plates Part 3: Strips: Tolerances on shape and dimensionsBS ISO 6361-3:2014 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6361-3:2014. The UK participatio
2、n in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are respo
3、nsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 84686 1 ICS 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the St
4、andards Policy and Strategy Committee on 30 September 2014. Amendments/corrigenda issued since publication Date T e x t a f f e c t e d ISO 2014 Wrought aluminium and aluminium alloys Sheets, strips and plates Part 3: Strips: Tolerances on shape and dimensions Aluminium et alliages daluminium corroy
5、s Tles, bandes et tles paisses Partie 3: Bandes: Tolrances sur forme et dimensions INTERNATIONAL STANDARD ISO 6361-3 Third edition 2014-09-15 Reference number ISO 6361-3:2014(E)BS ISO 6361-3:2014ISO 6361-3:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserv
6、ed. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
7、at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 6361-3:2014ISO 6361-3:2014(E) ISO 2014 All rights reser
8、ved iii Contents Page Foreword iv 1 Scope . 1 2 Dimensional tolerances 1 2.1 Thickness . 1 2.2 Width . 3 3 Shape tolerances . 3 Bibliography 5BS ISO 6361-3:2014ISO 6361-3:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
9、(ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, g
10、overnmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further mai
11、ntenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). At
12、tention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduct
13、ion and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conf
14、ormity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information. The committee responsible for this document is ISO/TC 79, Light metals and their alloys, Subcommittee SC 6, Wroug
15、ht aluminium and aluminium alloys. This third edition cancels and replaces the second edition (ISO 6361-3:2011), which has been technically revised. ISO 6361 consists of the following parts, under the general title Wrought aluminium and aluminium alloys Sheets, strips and plates: Part 1: Technical c
16、onditions for inspection and delivery Part 2: Mechanical properties Part 3: Strips: Tolerances on shape and dimensions Part 4: Sheets and plates: Tolerances on shape and dimensions Part 5: Chemical compositioniv ISO 2014 All rights reservedBS ISO 6361-3:2014INTERNATIONAL ST ANDARD ISO 6361-3:2014(E)
17、 Wrought aluminium and aluminium alloys Sheets, strips and plates Part 3: Strips: Tolerances on shape and dimensions 1 Scope This part of ISO 6361 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy strip by cold-rolling for general engineering applications. It
18、 applies to products with thickness of over 0,15 mm up to, and including 16 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock), or to special products such as those that are corrugated or embossed. Technical conditions for inspecti
19、on and delivery of products covered by this part of ISO 6361 are specified in ISO 6361-1. 2 Dimensional tolerances 2.1 Thickness Thickness tolerances shall be in accordance with Tables 1 and 2. When the tolerance is specified as either all plus, or minus side, the value in Table 1, or in Table 2, sh
20、all be doubled. Tolerances for the products exceeding the range of specified thickness and width shall be agreed upon by the purchaser and the supplier. Table 1 Thickness tolerances Dimensions in millimetres Specified thickness Alloy number 1050, 1050A, 1070, 1070A, 1080, 1080A, 1085, 1100, 1200, 11
21、00A, 1230A, 3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011A, 8021, 8079 Specified width Over Up to and including Up to and including 450 Over 450, up to and including 900 Over 900, up to and including 1 400 Over 1 400, up to and including 1 800 Over 1 800, up to and in
22、cluding 2 300 Over 2 300, up to and including 2 600 Tolerance 0,15 0,20 0,03 0,03 0,05 0,20 0,25 0,03 0,04 0,05 0,25 0,45 0,04 0,04 0,05 0,06 0,45 0,70 0,04 0,05 0,06 0,08 0,70 0,90 0,05 0,05 0,06 0,09 0,13 ISO 2014 All rights reserved 1BS ISO 6361-3:2014ISO 6361-3:2014(E) Specified thickness Alloy
23、number 1050, 1050A, 1070, 1070A, 1080, 1080A, 1085, 1100, 1200, 1100A, 1230A, 3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011A, 8021, 8079 Specified width Over Up to and including Up to and including 450 Over 450, up to and including 900 Over 900, up to and including 1
24、400 Over 1 400, up to and including 1 800 Over 1 800, up to and including 2 300 Over 2 300, up to and including 2 600 Tolerance 0,90 1,1 0,05 0,06 0,08 0,10 0,13 1,1 1,7 0,06 0,08 0,10 0,13 0,15 1,7 1,9 0,06 0,08 0,10 0,15 0,20 1,9 2,4 0,08 0,08 0,10 0,15 0,20 2,4 2,7 0,09 0,10 0,13 0,18 0,23 2,7 3,
25、6 0,11 0,11 0,13 0,18 0,23 0,25 3,6 4,5 0,15 0,15 0,20 0,23 0,28 0,30 4,5 5,0 0,18 0,18 0,23 0,28 0,33 0,38 5,0 6,5 0,23 0,23 0,28 0,33 0,38 0,43 6,5 8,0 0,33 0,33 0,33 0,38 0,43 0,51 8,0 11 0,48 0,48 0,48 0,48 0,58 0,66 11 16 0,64 0,64 0,64 0,64 0,76 0,89 Table 2 Thickness tolerances Dimensions in
26、millimetres Specified thickness Alloy number 2014, 2014A, 2017, 2017A, 2219, 2024, 2124,2 618A, 3004, 3104, 5021, 5026, 5040, 5042, 5049, 5052, 5059, 5070, 5449, 5251, 5154, 5154A, 5254, 5383, 5454, 5754, 5456, 5082, 5182, 5083, 5086, 6016, 6025, 6061, 6082, 7204, 7010, 7020, 7021, 7022, 7050, 7075,
27、 7475, 7178 Specified width Over Up to and includ- ing Up to and includ- ing 450 Over 450, up to and includ- ing 900 Over 900, up to and includ- ing 1 200 Over 1 200, up to and includ- ing 1 400 Over 1 400, up to and includ- ing 1 500 Over 1 500, up to and includ- ing 1 700 Over 1 700, up to and inc
28、lud- ing 1 800 Over 1 800, up to and includ- ing 2 000 Over 2 000, up to and includ- ing 2 100 Over 2 100, up to and includ- ing 2 300 Over 2 300, up to and includ- ing 2 400 Over 2 400, up to and includ- ing 2 600 Tolerance 0,20 0,25 0,03 0,04 0,06 0,06 0,25 0,45 0,04 0,04 0,06 0,09 0,45 0,70 0,04
29、0,05 0,06 0,09 0,10 0,10 0,10 0,70 0,90 0,05 0,05 0,06 0,10 0,13 0,13 0,13 0,15 0,90 1,1 0,05 0,06 0,08 0,10 0,13 0,13 0,13 0,15 1,1 1,7 0,06 0,08 0,10 0,13 0,15 0,15 0,15 0,18 1,7 1,9 0,08 0,08 0,10 0,13 0,15 0,15 0,15 0,18 1,9 2,4 0,09 0,09 0,10 0,13 0,15 0,15 0,15 0,18 0,18 0,30 2,4 2,7 0,10 0,10
30、 0,13 0,13 0,18 0,18 0,18 0,20 0,20 0,41 2,7 3,2 0,11 0,11 0,13 0,13 0,18 0,18 0,18 0,20 0,20 0,41 0,46 0,51Table 1 (continued) 2 ISO 2014 All rights reservedBS ISO 6361-3:2014ISO 6361-3:2014(E) Specified thickness Alloy number 2014, 2014A, 2017, 2017A, 2219, 2024, 2124,2 618A, 3004, 3104, 5021, 502
31、6, 5040, 5042, 5049, 5052, 5059, 5070, 5449, 5251, 5154, 5154A, 5254, 5383, 5454, 5754, 5456, 5082, 5182, 5083, 5086, 6016, 6025, 6061, 6082, 7204, 7010, 7020, 7021, 7022, 7050, 7075, 7475, 7178 Specified width Over Up to and includ- ing Up to and includ- ing 450 Over 450, up to and includ- ing 900
32、Over 900, up to and includ- ing 1 200 Over 1 200, up to and includ- ing 1 400 Over 1 400, up to and includ- ing 1 500 Over 1 500, up to and includ- ing 1 700 Over 1 700, up to and includ- ing 1 800 Over 1 800, up to and includ- ing 2 000 Over 2 000, up to and includ- ing 2 100 Over 2 100, up to and
33、includ- ing 2 300 Over 2 300, up to and includ- ing 2 400 Over 2 400, up to and includ- ing 2 600 Tolerance 3,2 3,6 0,11 0,11 0,13 0,13 0,18 0,25 0,30 0,33 0,36 0,41 0,46 0,51 3,6 4,5 0,15 0,15 0,20 0,20 0,23 0,30 0,36 0,38 0,41 0,43 0,48 0,58 4,5 5,0 0,18 0,18 0,25 0,25 0,28 0,36 0,41 0,43 0,43 0,4
34、3 0,56 0,66 5,0 6,5 0,23 0,23 0,28 0,28 0,33 0,41 0,46 0,46 0,46 0,46 0,61 0,71 6,5 8,0 0,33 0,33 0,33 0,33 0,38 0,46 0,51 0,51 0,51 0,51 0,64 0,76 8,0 11 0,48 0,48 0,48 0,48 0,51 0,51 0,58 0,58 0,64 0,64 0,66 0,84 11 16 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,76 0,76 0,76 0,89 0,89 2.2 Width Width tol
35、erances shall be in accordance with Table 3. When the tolerance is specified as either all plus, or minus side, the value in Table 3 shall be doubled. Tolerances for the products exceeding the range of specified thickness and width shall be agreed upon by the purchaser and the supplier. Table 3 Widt
36、h tolerance for strip Dimensions in millimetres Specified thickness Specified width Over Up to and including Up to and including 150 Over 150, up to and including 300 Over 300, up to and including 600 Over 600, up to and including 1 200 Over 1 200, up to and including 1 500 Over 1 500, up to and inc
37、luding 2 600 Tolerance 0,15 3,2 0,3 0,4 0,8 1,2 1,6 3,2 3,2 5,0 0,3 0,5 0,8 1,6 2,4 5,0 6,3 0,4 0,8 1,2 2,4 3,2 3 Shape tolerances The lateral curvature is the depth of the arc for any 2 000 mm basis lengths (see Figure 1).Table 2 (continued) ISO 2014 All rights reserved 3BS ISO 6361-3:2014ISO 6361-
38、3:2014(E) Key a deviation from straightness (maximum value) b width c 2 000 mm Figure 1 Lateral curvature of strip When tested with the strip resting on a flat surface, against a straight edge, the lateral curvature shall not exceed the values given in Table 4 for a value of length L = 2 000 mm. The
39、 maximum value for the products exceeding the range of specified thickness and width shall be agreed upon between the purchaser and the supplier. Table 4 Lateral curvature tolerances for strip Dimensions in millimetres Specified thickness Specified width Over Up to and including 15 or over, up to an
40、d including 25 Over 25, up to and including 50 Over 50, up to and including 100 Over 100, up to and including 250 Over 250, up to and including 2 600 Maximum value (in any 2 000 length) 0,15 1,6 19 15 10 7 5 1,6 3,2 10 7 54 ISO 2014 All rights reservedBS ISO 6361-3:2014ISO 6361-3:2014(E) Bibliograph
41、y 1 ISO 6361-1, Wrought aluminium and aluminium alloys Sheets, strips and plates Part 1: Technical conditions for inspection and delivery ISO 2014 All rights reserved 5BS ISO 6361-3:2014ISO 6361-3:2014(E) ISO 2014 All rights reserved ICS 77.150.10 Price based on 5 pagesThis page deliberately left bl
42、ankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution
43、 (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been careful
44、ly assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out
45、 more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard c
46、opies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further i
47、nformation on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with
48、 standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit
