BS ISO 702-2-2007 en_7703 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Camlock type《机床.主轴头和工件卡盘的连接尺寸规格.凸轮锁紧型》.pdf
《BS ISO 702-2-2007 en_7703 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Camlock type《机床.主轴头和工件卡盘的连接尺寸规格.凸轮锁紧型》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 702-2-2007 en_7703 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Camlock type《机床.主轴头和工件卡盘的连接尺寸规格.凸轮锁紧型》.pdf(18页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS ISO 702-2:2007 Machine tools Connecting dimensions of spindle noses and work holding chucks Part 2: Camlock type ICS 25.060.20 Incorporating October 2009 corrigendum National foreword This British Standard is the UK implementation of ISO 702-2:2007, incorporating corrigendum Octo
2、ber 2009. The UK participation in its preparation was entrusted to Technical Committee MTE/1, Machine tools. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Use
3、rs are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. BS ISO 702-2:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2010 Amendments/corrigend
4、a issued since publication Date Comments 28 February 2010 Implementation of ISO corrigendum October 2009, igure 2 repl ced and Tables 1 and 8 modified ISBN 978 0 580 69577 3 F a Reference number ISO 702-2:2007(E)INTERNATIONAL STANDARD ISO 702-2 Second edition 2007-10-15 Machine tools Connecting dime
5、nsions of spindle noses and work holding chucks Part 2: Camlock type Machines-outils Dimensions dassemblage des nez de broches et des mandrins porte-pices Partie 2: Type Camlock BS ISO 702-2:2007 ii iii Contents Page Foreword iv 1 Scope . 1 2 Interchangeability . 1 3 Sizes for interchangeability . 2
6、 3.1 Spindle noses 2 3.2 Cams 4 3.3 Studs 6 3.4 Face plates 8 3.5 Accessories for spindle noses and face plates. 9 Bibliography . 11 BS ISO 702-2:2007iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The w
7、ork of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-govern
8、mental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The
9、 main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
10、 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 702-2 was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 8, Work hold
11、ing spindles and chucks. This second edition cancels and replaces the first edition (ISO 702-2:1975), of which all the clauses, tables and figures have been technically revised. ISO 702 consists of the following parts, under the general title Machine tools Connecting dimensions of spindle noses and
12、work holding chucks: Part 1: Conical connection Part 2: Camlock type Part 3: Bayonet type Part 4: Cylindrical connection BS ISO 702-2:2007 1 Machine tools Connecting dimensions of spindle noses and work holding chucks Part 2: Camlock type 1 Scope This part of ISO 702 specifies the sizes for intercha
13、ngeability of cylindrical spindle noses and corresponding connecting faces of face plates or work holding chucks. NOTE The “conical connection”, “bayonet type” and “cylindrical connection” are dealt with in ISO 702-1, ISO 702-3 and ISO 702-4, respectively. 2 Interchangeability In this part of ISO 70
14、2, all the dimensions and tolerances are expressed in millimetres. Although internal mounting components and assembly screws are not respectively interchangeable, as they may conform with either the metric or inch series, there is complete interchangeability between metric spindle noses and face pla
15、tes in inches and vice versa. BS ISO 702-2:20072 3 Sizes for interchangeability 3.1 Spindle noses Key 1 size No. 3 2 size No. 4 3 size Nos. 5 to 20 aReference line. Figure 1 Spindle noses BS ISO 702-2:2007 3 Table 1 Dimensions of spindle noses Size No. Dimension 3 4 5 6 8 11 15 20 nom. 53,975 63,513
16、 82,563 106,375 139,719 196,869 285,775 412,775 d 1 tol. +0,008 0 +0,008 0 +0,010 0 +0,010 0 +0,012 0 +0,014 0 +0,016 0 +0,020 0 d 265 82 114 172 258 380 d 370,6 82,6 104,8 133,4 171,4 235,0 330,2 463,6 d 492 117 146 181 225 298 403 546 d 5 +0,05 0 15,1 16,7 19,8 23,0 26,2 31,0 35,7 42,1 d 6H8 19 19
17、 22 26 29 32 35 42 d 7M8 M8 M6 M8 M8 M8 M10 M10 d 815,5 15,5 10,5 13,5 13,5 13,5 16,5 16,5 e 11 11 13 14 16 18 19 21 f min. 32 34 38 45 50 60 70 82 g 0,05 22,6 27,0 h 0,2 30 40 j 17,5 17,5 20,6 23,8 27,0 31,8 36,5 42,9 k 0,1 11,1 11,1 13,5 15,9 18,25 21,45 24,6 28,6 l+0,2 0 27,5 36 46 57 64 75 84 94
18、 m 7 9 9 9 11 11 w 0,1 0,15 0,15 0,15 0,15 0,15 0,15 0,15 x 0,2 0,2 0,2 0,2 0,2 0,2 0,2 0,2 18 18,6 15 36 14 55 13 46 12 18 10 30 8 35 7 05 NOTE General tolerance for untoleranced dimensions: 0,4 mm. BS ISO 702-2:20074 BS ISO 702-2:2007 3.2 Cams aReference line. Figure 2 Cams 5 Table 2 Dimensions of
19、 cams Size No. Dimension 3 4 5 6 8 11 15 20 a min. 13 17 22 25 28 32 37 43 b0 0,2 13,4 11,9 14,2 16,7 18,9 21,2 23,5 27,8 c 7 10 10 10 10 10 d+0,3 0 1,65 1,60 1,45 2,56 2,46 2,44 2,35 3,10 e+0,1 0 0,15 0,15 0 0,45 0,36 0,28 0,20 0,50 h0 0,1 26,5 35 45 56 63 73 82 92 i 0,1 2,2 2,2 3,0 4,2 5,3 8,7 6,0
20、 6,0 j 3,6 0,05 3,6 0,05 5,0 0,1 6,5 0,1 6,5 0,1 6,5 0,1 8,5 0,1 8,5 0,1 k e8 19 19 22 26 29 32 35 42 l 13 0,2 13 0,2 14 17 21 24 27 33 m 0,05 4,5 6 6 6 8 8 n 0,1 2,0 2,85 3,95 7,35 5,2 5,2 o 0,2 14,9 16,7 22,4 30,2 33,2 39,5 43,6 48,4 p 21,4 26,5 35,0 43,0 49,0 59,0 62,0 69,0 q D12 8 10 11 12 14 17
21、 17 22 r 7,5 9,5 11,1 12,7 14,2 16,7 19,0 22,2 s 13 15 15 15 15 15 t 8 9 11 12 14 16 16 20 u 1,2 1,2 Slope on v a1,60 1,90 1,90 2,64 2,64 2,64 2,64 3,18 15 10 10 10 10 15 15 15 15 15 15 20 20 20 20 20 NOTE General tolerance for untoleranced dimensions: 0,4 mm. aSee tolerance on dimensions d and e. B
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO70222007EN_7703MACHINETOOLSCONNECTINGDIMENSIONSOFSPINDLENOSESANDWORKHOLDINGCHUCKSCAMLOCKTYPE 机床

链接地址:http://www.mydoc123.com/p-391279.html