1、BSI Standards Publication BS ISO 9928-1:2015 Cranes Crane operating manual Part 1: GeneralBS ISO 9928-1:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 9928-1:2015. The UK participation in its preparation was entrusted to Technical Committee MHE/3/11, Cr
2、ane safety and testing. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 201
3、5. Published by BSI Standards Limited 2015 ISBN 978 0 580 87794 0 ICS 53.020.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2015. Amendments/corrige
4、nda issued since publication Date T e x t a f f e c t e d ISO 2015 Cranes Crane operating manual Part 1: General Appareils de levage charge suspendue Manuel lusage des oprateurs Partie 1: Gnralits INTERNATIONAL STANDARD ISO 9928-1 Second edition 2015-06-15 Reference number ISO 9928-1:2015(E)BS ISO 9
5、928-1:2015ISO 9928-1:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, incl
6、uding photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland
7、Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgBS ISO 9928-1:2015ISO 9928-1:2015(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 4 Presentation of the manual . 1 4.1 General . 1 4.2 Preliminary information . 2 4.3 Number of books . 2 5 Contents
8、 of the operating manual 2 5.1 Technical data 2 5.2 Special safety advice . 2 5.2.1 Crane 2 5.2.2 Operating area . 3 5.2.3 Setting up of the crane 3 5.2.4 Securing of the crane 3 5.2.5 Working clothes and personal equipment. 3 5.3 Operators aids and controls . 3 5.4 Operators instructions 3 5.5 Load
9、 diagrams and load tables . 3 5.6 Safety devices . 3 5.7 Environmental conditions . 3 ISO 2015 All rights reserved iii Contents PageBS ISO 9928-1:2015ISO 9928-1:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO membe
10、r bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmenta
11、l and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance a
12、re described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is
13、 drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or
14、 on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity ass
15、essment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information. The committee responsible for this document is ISO/TC 96, Cranes, Subcommittee SC 5, Use, operation and maintenance. This se
16、cond edition cancels and replaces the first edition (ISO 9928-1:1990), of which it constitutes a minor revision. Notably, driving has been replaced by operating in the title and “driving” /”driver” by “operation/operator” throughout the text. ISO 9928 consists of the following parts, under the gener
17、al title Cranes Crane operating manual: Part 1: General Part 2: Mobile cranesiv ISO 2015 All rights reservedBS ISO 9928-1:2015INTERNATIONAL ST ANDARD ISO 9928-1:2015(E) Cranes Crane operating manual Part 1: General 1 Scope This part of ISO 9928 specifies general requirements for the contents of a cr
18、ane operating manual. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced documen
19、t (including any amendments) applies. ISO 4306 (all parts), Cranes Vocabulary ISO 80000-1, Quantities and units Part 1: General ISO 80000-4, Quantities and units Part 4: Mechanics 3 T erms a nd definiti ons For the purposes of this document, the terms and definitions given in ISO 4306-1 and the foll
20、owing apply. 3.1 crane operator person who operates the crane for the purpose of positioning loads Note 1 to entry: The term driver is then used to refer to that person who operates only those controls which move the crane from place to place. 4 Presentation of the manual 4.1 General A manual shall
21、be provided by the manufacturer which a) should be simple to understand and have adequate explanatory notes, b) shall incorporate the use of internationally recognized symbols, c) should be easy to use, compact and made of durable hardwearing material, and d) shall be compiled in the language agreed
22、 between the parties to the contract. The presentation of the manual is important. It is a working tool which should be both convenient and complete. The text should be simple and adapted to the individuals who will use it, with all information being explicit and comprehensive. Illustrations, diagra
23、ms, graphs and tables should be used with the purpose of avoiding risk of misunderstanding and in preference to written text. They should be clear, simple and be placed adjacent to the corresponding reference. ISO 2015 All rights reserved 1BS ISO 9928-1:2015ISO 9928-1:2015(E) The terms and definitio
24、ns (see ISO 4306), and the units and symbols (see ISO 80000-1 and ISO 80000-4) shall comply with the relevant International Standards. When the units specified on the equipment are different from those in common use, reference should be made in brackets or by means of a footnote. Only those items re
25、lative to the particular crane and its application shall be included. 4.2 Preliminary information The following information shall be given on the front or back cover, or on the first pages of the manual: a) the title of the manual; b) the reference number of the manual (if any); c) the designation (
26、type) of the crane: d) the type or series of crane (if any); e) the serial number or numbers of the crane or, where appropriate, the range of serial numbers covered; f) the name and full address of the manufacturer and/or agent; g) a table of contents; h) an index (optional); i) the basic characteri
27、stics of the crane. 4.3 Number of books The crane operating manual, along with other crane manuals (maintenance manual, user manual, etc.), may be published as one or more books. The choice of the size and grouping of the books should be suitable for the type of product, its normal application and p
28、ersonnel requirements. Where appropriate, cross-reference to other parts of the book should be made so that the same information is not repeated unnecessarily. 5 Contents of the operating manual 5.1 Technical data The manual shall include a) a drawing/sketch of the crane assembly with the number and
29、 designation of the main components; b) all technical data of importance for the operator to ensure safe transport, erection and dismantling, etc. of the crane. 5.2 Special safety advice The manual shall contain applicable safety advice, together with the appropriate safety symbol. Typical examples
30、are given in 5.2.1 to 5.2.5. 5.2.1 Crane “Switches and connectors shall not be opened until the power supply has been switched off.” “Do not use the emergency stop device in order to stop normal motion.”2 ISO 2015 All rights reservedBS ISO 9928-1:2015ISO 9928-1:2015(E) 5.2.2 Operating area “Install
31、fencing to prevent unauthorized people from entering the operating area of an automatically operated crane.” 5.2.3 Setting up of the crane “Do not use the crane before the outriggers are in position.” 5.2.4 Securing of the crane “Set the wheel brakes and ground anchors.” 5.2.5 Working clothes and pe
32、rsonal equipment “Always use a safety rope when working on the structure of the crane.” 5.3 Operators aids and controls The manual shall include a drawing/sketch of instruments, indicators, controls and diagnostic modules seen from the operators position and a description and explanation of their fu
33、nctions. 5.4 Operators instructions The instructions shall specify the duties of the operator prior to operation, during operation, and after finishing operations. Special instructions shall be given if the crane is to be transported before being put into use. 5.5 Load diagrams and load tables AII n
34、ecessary load diagrams and tables shall be included. 5.6 Safety devices A drawing/sketch of the crane with location of the devices shall be included. Where appropriate, enlarged drawings/sketches of devices should be shown. Instructions about any necessary setting of tripped safety devices required
35、to be carried out by the operator shall be included. 5.7 Environmental conditions Where appropriate, an indication of maximum allowable wind speed and extreme working temperature and other possible restrictions on the operation shall be given. ISO 2015 All rights reserved 3BS ISO 9928-1:2015ISO 9928
36、-1:2015(E) ISO 2015 All rights reserved IC S 53.020.20 Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standar
37、ds and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experie
38、nce and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Infor
39、mation on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publication
40、s, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscrip
41、tions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your d
42、esktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updat
43、ing service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you
44、 are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our British Standards and other publications
45、 are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and document
46、ation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publi
47、cation and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice c
48、an be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
