1、PUBLISHED DOCUMENT PD CEN/TR 15438:2007 Plastics piping systems Guidance for coding of products and their intended uses ICS 23.040.20 PD CEN/TR 15438:2007 This Published Document was published under the authority of the Standards Policy and Strategy Committee on 28 February 2007 BSI 2007 ISBN 978 0
2、580 50265 1 National foreword This Published Document was published by BSI. It is the UK implementation of CEN/TR 15438:2007. The UK participation in its preparation was entrusted to Technical Committee PRI/88, Plastics piping systems. A list of organizations represented on PRI/88 can be obtained on
3、 request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Amendments issued since publication Amd. No. Date CommentsTECHNICALREPORT RAPPORTTECHNIQUE TECHNISCHERBERICHT CEN/TR15438 January2007
4、 ICS23.040.20 EnglishVersion PlasticspipingsystemsGuidanceforcodingofproductsand theirintendeduses SystmesdecanalisationsenplastiquesGuidepourle codagedeproduitsetdeleursutilisationsprvues KunststoffRohrleitungssystemeAnleitungzurCodierung vonProduktenundderenVerwendungszwecke ThisTechnicalReportwas
5、approvedbyCENon16April2006.IthasbeendrawnupbytheTechnicalCommitteeCEN/TC155. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Bulgaria,Cyprus,CzechRepublic,Denmark,Estonia,Finland, France,Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland
6、,P ortugal, Romania,Slovakia,Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2007CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnati
7、onalMembers. Ref.No.CEN/TR15438:2007:E2 Contents Page Foreword 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Symbols and shortcuts, terms and definitions 5 3.1 General 5 3.2 Materials and products 5 3.3 Intended uses 6 3.4 Classes 8 Annex A (informative) Marking differences in GRP product st
8、andards 10 Bibliography 11 CEN/TR 15438:20073 Foreword This document (CEN/TR 15438:2007) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This document is drafted in the three official CEN languages. In the ta
9、bles of Clause 3 there is free space left for CEN Member bodies to add its own national language(s) to the symbols. CEN/TR 15438:20074 Introduction For PE pressure piping systems, since the late 1980s, it is common practice to use a code indicating the intended use. This information is put on the pi
10、pe, the label of a fitting or valve or the packaging. It may also be repeated in manufacturers technical files. With the introduction of harmonised European Standards related to the Construction Products Directive 1a lot of information shall accompany the CE marking symbol. Guidance Paper D 2gives r
11、ecommendations to the specification writers: “Use of “codified” formats: Where additional information on the declared performances of harmonised characteristics is required, or to define the product, its intended use or its end-use condition, specification writers should explore the possibilities of
12、 using abbreviated forms of presentation (defined symbols, standard designations, classes of convenience or pictograms). Where this is done, it is important that specification writers ensure the consistent applications of such “codified” formats across product families“. “Intended uses: Possible int
13、ended uses for the product(s) should be defined in the technical specification, together with appropriate reference terms, or symbols, to be used in the information accompanying the CE marking, if necessary. Products with more than one intended use will need to be accompanied by sufficient informati
14、on to cover all of them, but the technical specification should provide some flexibility in the presentation of this information, if appropriate“. CEN/TR 15438:20075 1 Scope This Technical Report gives guidance for the coding of products, their classification and intended uses for plastics piping sy
15、stems. It lays down reference terms and symbols to be used when establishing documentation accompanying the CE marking according to the European Directives. 2 Normative references The following referenced documents are indispensable for the application of this Technical Report. For dated references,
16、 only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 472, Plastics Vocabulary (ISO 472:1999). EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (I
17、SO 1043-1:2001). EN ISO 1043-2, Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materials (ISO 1043-2:2000). EN ISO 1043-3, Plastics Symbols and abbreviated terms Part 3: Plasticizers (ISO 1043-3:1996). EN ISO 1043-4, Plastics Symbols and abbreviated terms Part 4: Flame retard
18、ants (ISO 1043-4:1998). EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using test data from reaction to fire tests. ISO 12176-4, Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 4: Traceability coding. ISO/FDIS
19、 13950, Plastics pipes and fittings Automatic recognition systems for electrofusion joints (Intended as replacement for ISO/TR 13950:1997). 3 Symbols and shortcuts, terms and definitions 3.1 General Symbols, shortcuts, terms and definitions given in this Technical Report are primarily based on exist
20、ing standards as EN ISO 1043 parts 1 to 4, EN 13501-1, ISO 12176-4 and ISO/FDIS 13950, as well as on internal CEN/TC1553and ISO/TC1384Guidance papers and national standards5to which are only added new items necessary to respond to the need of CE marking rules. Additional information may be given in
21、specific product standards. 3.2 Materials and products Reference to material or product symbols or shortcuts can be found in the standards given in Table 1. NOTE It is intended that the CEN member body adds its own national language(s) to the tables given in this clause. CEN/TR 15438:20076 Table 1 M
22、aterial or product symbols or shortcuts Symbols or shortcuts for Standards en: Plastics in general (vocabulary) fr: Les plastiques en gnrale (vocabulaire) de: Kunststoffe im allgemeinen (Fremdwrterverzeichnis) EN ISO 472 en: Basic polymers fr: Polymres de base de: Basis-Polymere EN ISO 1043-1 en: Fi
23、llers and reinforcing materials fr: Charges et matriaux de renforcement de: Fllstoffe und Verstrkungsstoffe EN ISO 1043-2 en: Plasticizers fr: Plastifiants de: Weichmacher EN ISO 1043-3 en: Flame retardants fr: Ignifuges de: Flammschutzmittel EN ISO 1043-4 en: Reaction to fire classification fr: Cla
24、ssification raction au feu de: Klassifizierung des Brandverhaltens EN 13501-1 en: Traceability coding fr: Codage de la traabilit de: Rckverfolgbarkeits-Code ISO 12176-4 en: Pictograms for electrofusion elements fr: Pictogrammes pour lments lectrosoudables de: Piktogramme fr Elektro-Schweisselemente
25、ISO/FDIS 13950 3.3 Intended uses Table 2 gives the applicable term that should be used for the intended use. CEN/TR 15438:20077 Table 2 Intended uses Term a bDefinition GAS en: Supply of gaseous fuels fr: Distribution de combustibles gazeux de: Gasversorgung W en: Drinking water supply, pressure fr:
26、 Alimentation en eau potable, pression de: Trinkwasserversorgung, Druck P cen: Drainage and sewerage, pressure fr: Branchement et collecteurs dassainissement, sous pression de: Entwsserungs- und Abwasserrohrleitungen, Druck H cen: Hot water, pressure fr: Eau chaude, pression de: Warmwasser, Druck HW
27、 en: Hot (and cold) drinking water, pressure fr: Eau potable chaude (et froide), pression de: Trinkwasser warm (und kalt), Druck B en: Soil and waste discharge within the building structure, non-pressure fr: Evacuation des eaux-vannes et des eaux uses lintrieur de la structure des btiments, sans pre
28、ssion de: Abwasser innerhalb der Gebudestruktur, drucklos U en: Underground drainage and sewerage, non-pressure fr: Branchements et collecteur dassainissement enterrs, sans pression de: Erdverlegte Abwasserkanle und leitungen, drucklos UD en: Underground drainage and sewerage and under the building
29、structure, non-pressure fr: Branchements et collecteur dassainissement enterrs et sous la structure des btiments, sans pression de: Erdverlegte Abwasserkanle und leitungen und unter der Gebudestruktur, drucklos BD en: Soil and waste discharge within and under the building structure, non-pressure fr:
30、 Evacuation des eaux uses lintrieur et sous la structure des btiments, sans pression de: Abwasser innerhalb und unter der Gebudestruktur, drucklos R cen: Rainwater above ground, outside buildings fr: Eau pluviale hors sol, lxterieur du btiment de: Regenwasser ber Grund, ausserhalb des Gebudes C en:
31、Cable ducting fr: Protection de cbles de: Kabelschutz L en: Land drainage fr: Drainage du sol de: Bodenentwsserung I en: Irrigation fr: Irigation de: Bewsserung CEN/TR 15438:20078 Table 2 (concluded) FH en: Floor (ground) heating fr: Chauffage du sol de: Bodenheizung CO en: Cooling fr: Refroidisseme
32、nt de: Khlung RH en: Radiator connections fr: Connections radiateurs de: Radiator-Anbindungen JP en: Jacquet pipe fr: Tubes Jacquet de: Jacquet-Rohre VE en: Ventillation fr: Ventillation de: Lftung IS en: Industrial applications fr: Applications industrielles de: Industrielle Anwendung F en: Fire ex
33、tinction system fr: System dextinction du feu de: Feuerlschsystem aIf for a product more than one term applies, marking may be as follows: e.g. “GAS+W+P“ or “UD/BD“. bIn some Member States well established national coding according to national QMs are used. It is therefore recommended to give the re
34、lation between both terms in the technical file of the product. c For GRP products these terms may have a different meaning. For clarification see Annex A of this Technical Report3.4 Classes Table 3 gives the applicable term or symbol that should be used for the class under consideration. CEN/TR 154
35、38:20079 Table 3 Classes Term Definition PNaen: Nominal pressure fr: Pression nominale de: Nenndruck SNaen: Ring stiffness fr: Rigidit annulaire de: Ringsteifigkeit RFaen: Ring flexibility fr: Flxibilit annulaire de: Ringflexilbilitt HC aen: Hot water class fr: Classe deau chaude de: Warmwasser-Klas
36、se ben: Reaction to fire class fr: Classe comportement au feu de: Brandverhaltens-Klasse en: Impact resistance class (in cold environment) fr: Classe rsistance limpacte (dans un environnemet froide) de: Schlagfestigkeits-Klasse (in der Klte) IMP 23 C en: Impact resistance class (at 23C) fr: Classe r
37、sistance limpacte ( 23C) de: Schlagfestigkeits-Klasse (bei 23C) aThe term shall be followed by a figure/figures as given in the relevant product standard. bThe sign shall be followed by the classification as given in EN 13501-1. CEN/TR 15438:200710 Annex A (informative) Marking differences in GRP pr
38、oduct standards This Annex gives clarification on terms which may have a different meaning in the GRP product standards EN 1796 6and EN 14364 7 . Table AA.1 Meaning of terms in GRP standards Term Definition R en: Suitable for axial loading fr: Utilisable avec une charge axiale de: Brauchbar fr axial
39、e Belastung RA en: Suitable for axial loading and tested according to the Annex of the GRP standard fr: Utilisable avec une charge axiale et soumis essai selon lAnnexe de la norme PRV de: Brauchbar fr axiale Belastung und geprft gemss Anhang der GFK-Norm H en: Aboveground use fr: Utilisation hors so
40、l de: Gebrauch ber Grund P en: Use with potable water fr: Utilisable avec de leau potable de: Gebrauch mit Trinkwasser NOTE These terms could be aligned with this Technical Report once the GRP standards will undergo a revision CEN/TR 15438:200711 Bibliography 1 CPD, Council Directive 89/106/EEC of 2
41、1 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products. 2 Guidance Paper D, CE Marking under The Construction Products Directive. 3 CEN/TC155 N 987:1993, Internal Guide for CEN/TC155 Minimum required marking. 4 I
42、SO/TC138-IG2:1990, Internal Guide ISO/TC138 Plastics piping systems Minimum required marking of components. 5 DIN 2429-2, Symbolic representation of pipework components on engineering drawings Functional representation. The title shall be in German, unless an English version of this DIN exists. 6 EN
43、 1796, Plastics piping systems for water supply with or without pressure Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). 7 EN 14364, Plastics piping systems for drainage and sewerage with or without pressure - Glass- reinforced thermosetting plastics (GRP) ba
44、sed on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints. CEN/TR 15438:2007PD CEN/TR 15438:2007 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the
45、UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to impr
46、ove the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000.
47、 Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Servic
48、es. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Li
