1、PD ISO/TS 13399-71:2016 Cutting tool data representation and exchange Part 71: Graphical data layout Creation of documents for standardized data exchange: Graphical product information BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06PD ISO/TS 13399-71:2016 PUBLISHED
2、 DOCUMENT National foreword This Published Document is the UK implementation of ISO/TS 13399-71:2016. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obt
3、ained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 91035 7 ICS 25.100.01; 35.240.
4、50 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 July 2016. Amendments issued since publication Date Text affectedPD ISO/TS 13399-71:2016 ISO 2016 Cuttin
5、g tool data representation and exchange Part 71: Graphical data layout Creation of documents for standardized data exchange: Graphical product information Reprsentation et change des donnes relatives aux outils coupants Partie 71: Format des donnes graphiques Cration de documents pour lchange de don
6、nes normalises: Informations graphiques des produits TECHNICAL SPECIFICATION ISO/TS 13399-71 Reference number ISO/TS 13399-71:2016(E) First edition 2016-07-15PD ISO/TS 13399-71:2016ISO/TS 13399-71:2016(E)ii ISO 2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland
7、All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested
8、 from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgPD ISO/TS 13399-71:2016ISO/TS 13399-71:2016(E)Forewor
9、d iv Introduction vi 1 Scope . 1 2 Normative references 1 3 Fundamental system description 2 4 Definition of the dr a wing elements 2 4.1 Drawing frame . 2 4.2 Graphic of the cutting tool . 3 4.3 Manufacturer/supplier block . 3 4.4 Data table . 3 4.5 Mapping list . 3 5 Structure and layout of the dr
10、awing elements 3 5.1 Drawing frame . 3 5.2 Tool graphic . 3 5.3 Manufacturer/supplier block . 4 5.3.1 General 4 5.3.2 Data content and size of the fields 4 5.3.3 Design of the manufacturer block . 4 5.4 Data table for drawing header and bill of material . 5 5.5 Internal mapping list . 5 6 Functional
11、 description . 5 6.1 General . 5 6.2 Workflow for standard tools . 5 6.3 Workflow for custom solution tools . 6 Bibliography 8 ISO 2016 All rights reserved iii Contents PagePD ISO/TS 13399-71:2016ISO/TS 13399-71:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide
12、 federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that
13、committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this docume
14、nt and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives
15、, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development
16、 of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO speci
17、fic terms and expressions related to conformit y assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html. The committee responsible for this document is ISO/
18、TC 29, Small tools. ISO 13399 consists of the following parts, under the general title Cutting tool data representation and exchange: Part 1: Overview, fundamental principles and general information model Part 2: Reference dictionary for the cutting items Technical Specification Part 3: Reference di
19、ctionary for tool items Technical Specification Part 4: Reference dictionary for adaptive items Technical Specification Part 5: Reference dictionary for assembly items Technical Specification Part 50: Reference dictionary for reference systems and common concepts Technical Specification Part 60: Ref
20、erence dictionary for connection systems Technical Specification Part 70: Graphical data layout Layer settings for tool layout Technical Specification Part 71: Graphical data layout Creation of documents for the standardized data exchange Graphical product information Technical Specification Part 72
21、: Creation of documents for the standardized data exchange Definition of properties for drawing header and their XML-data exchange Technical Specification Part 150: Usage guidelines Technical Specification Part 201: Creation and exchange of 3D models Regular inserts Technical Specification Part 202:
22、 Creation and exchange of 3D models Irregular inserts Technical Specification Part 203: Creation and exchange of 3D models Replaceable inserts for drilling Technical Specificationiv ISO 2016 All rights reservedPD ISO/TS 13399-71:2016ISO/TS 13399-71:2016(E) Part 204: Creation and exchange of 3D model
23、s Inserts for reaming Technical Specification Part 301: Concept for the design of 3D models based on properties according to ISO/TS 13399-3: Modelling of thread-cutting taps, thread-forming taps and thread-cutting dies Technical Specification Part 302: Concept for the design of 3D models based on pr
24、operties according to ISO/TS 13399-3: Modelling of solid drills and countersinking tools Technical Specification Part 303: Creation and exchange of 3D models Solid end mills Technical Specification Part 304: Creation and exchange of 3D models Solid milling cutters with arbor hole Technical Specifica
25、tion Part 307: Creation and exchange of 3D models End mills for indexable inserts Technical Specification Part 308: Creation and exchange of 3D models Milling cutters with arbor hole for indexable inserts Technical Specification Part 309: Creation and exchange of 3D models Tool holders for indexable
26、 inserts Technical Specification Part 311: Creation and exchange of 3D models Solid reamers Technical Specification Part 312: Creation and exchange of 3D models Reamers for indexable inserts Technical Specification Part 401: Creation and exchange of 3D models Converting, extending and reducing adapt
27、ive items Technical Specification Part 403: Creation and exchange of 3D models Modelling of driven tool units Technical Specification Part 405: Creation and exchange of 3D models Collets Technical Specification Part 406: Creation and exchange of 3D models Modelling of connection interface Technical
28、Specification The following parts are under preparation: Part 80: Creation and exchange of 3D models Overview and principles Technical Specification Part 100: Definitions, principles and methods for reference dictionaries Technical Specification Part 305: Creation and exchange of 3D models Modular t
29、ooling systems with adjustable cartridges for boring Technical Specification Part 310: Creation and exchange of 3D models T urning tools with carbide tips Technical Specification Part 313: Creation and exchange of 3D models Creation and exchange of 3D models Burrs Technical Specification Part 314: C
30、reation and exchange of 3D models Creation and exchange of 3D models Cartridges for indexable inserts Technical Specification Part 315: Creation and exchange of 3D models Modelling of machine operated feed out tools T echnical Specification ISO 2016 All rights reserved vPD ISO/TS 13399-71:2016ISO/TS
31、 13399-71:2016(E) Introduction This part of ISO/TS 13399 defines the terms, properties and definitions of the drawing frame and drawing content of a computer-aided design. The purpose of this part of ISO/TS 13399 is to provide a common way of an electronic data exchange of graphical product informat
32、ion. However, the aim is the simplified communication during the phase of documentation namely on the basis of 2D drawings. Within the 2D drawing, the aim is to separate the proper product description (2D graphic) from the users specific presentation (drawing header). Most of the design orders are f
33、orced to use the individual drawing frames of the users. Therefore, a big portion of the design expenditure is used for the creation of the documentation and not for the proper problem solution. Drawings are the most important communicative devices of a producing company. Besides the description of
34、complex workpiece geometries, most cases are requests for correspondent documentation, e.g. to support NC-programming or production facilities. This part of ISO/TS 13399 defines a standardized data exchange format for documentation. Therefore, the effort for maintenance of the documentation is reduc
35、ed because the product drawing of the supplier or manufacturer is merged automatically into the individual drawing frames of the end users. This concept provides advantage for both supplier/manufacturer and end user, since the particular template is centrally maintained once only. To support a stand
36、ardized electronic product data exchange, the content of drawing headers have been examined by means of their common basic elements and the applicability. The identified data fields have been consolidated and may be used for a universal application because of a unified definition of their attributes
37、. Thus, in a defined use case, the graphical product description (2D graphic) and the descriptive data of the product (content of the drawing header) can be merged and filed as a complete drawing documentation.vi ISO 2016 All rights reservedPD ISO/TS 13399-71:2016TECHNICAL SPECIFICATION ISO/TS 13399
38、-71:2016(E) Cutting tool data representation and exchange Part 71: Graphical data layout Creation of documents for standardized data exchange: Graphical product information 1 Scope This part of ISO/TS 13399 determines the elements to be used for the creation of 2D documentation. The individual parts
39、 of documentation are drawing content, geometrical data, drawing frame and drawing header data as shown in Figure 1. The standardization of drawing formats, e.g. drawing frame, structure of the bill of material, are out of the scope of this part of ISO/TS 13399. Furthermore, it is intended to standa
40、rdize the data exchange of the product documentation. This part of ISO/TS 13399 specifies a common way for the basic principles for the creation of product documentation that contain the following: definitions and identifications of the elements of a product documentation; definitions and identifica
41、tions of the internal structure of the product documentation; definitions and identifications of those elements and features that are necessary to show the protection notices and the copyrights of the originator of the document. The following are outside the scope of this part of ISO/TS 13399: layer
42、 settings as defined in ISO/TS 13399-70; structure of the data exchange file using extensible mark-up language (XML); applications where these standard data may be stored or referenced; concept of the classification of cutting tool data and their properties; concept of the design of 2D drawings for
43、cutting tools; concept of the design of 3D models for cutting tools; application data for the use of those cutting tools; information about the reconditioning of cutting tools; information about additional application and usage data (e.g. coolant supply). 2 Normative references The following documen
44、ts, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/TS 13399-70, Cutting too
45、l data representation and Part 70: Graphical data layout Layer setting for tool layout ISO 2016 All rights reserved 1PD ISO/TS 13399-71:2016ISO/TS 13399-71:2016(E) ISO/TS 13399-72, Cutting tool data representation and exchange Part 72: Creation of documents for the standardized data exchange Definit
46、ion of properties for drawing header and their XML-data exchange 3 Fundamental system description The way of creating 2D cutting tool documentation and the necessary elements are given in Figure 1. In this part of ISO/TS 13399, the defined procedure for the creation of documentation is applicable fo
47、r standard and custom solution tools. In principle, cutting tool documentation consists of four main elements. These elements are shown in Figure 1. Figure 1 System for the creation of a 2D documentation 4 De finiti on of the dr a wing elements 4.1 Drawing frame The design of the drawing frame shall
48、 follow the definitions given in ISO/TS 13399-70. The drawing frame shall consists of the following: the definition of the content; the position of the custom-specific drawing header date, including the organizational data; the layout of the bill of material; the definition of the available drawing
49、area.2 ISO 2016 All rights reservedPD ISO/TS 13399-71:2016ISO/TS 13399-71:2016(E) 4.2 Graphic of the cutting tool The manufacturer shall create the cutting tool layout. The structure and design shall follow the rules according to ISO/TS 13399-70. The content of the drawing shall be positioned automatic
